WY Near perfect Blazer floor

[sharpie1972]

Near perfect complete Blazer floor from a low mile 71. A few torch kisses that will be covered by bolts. No rust or damage. Probably best to pick up, but I will crate and deliver to the freight depot with shipping paid by buyer. I will also be travelling east to Fargo, ND and then north into Minnesota in July and can transport that far for fuel costs. $650. Thanks, Sharpie SOLD

[sharpie1972]

More pics

[sharpie1972]

Also have very clean set of wheel tubs out of this one $100. Buyer pays shipping. Wheel tubs SOLD to SWYFOR5 Thanks, Sharpie

[1949gmc]

Those are GREAT pieces, my friend. Leave it to you to have such nice stuff!

[JimmyFloyd]

you have no idea how much I need that. Too bad you are so far away. Wonder what shipping would actually cost to 13790

[bigdon-70blazer]

Can you please get me some high resolution pics of the remnant of the jacking instructions decal?

[sharpie1972]

I'll see what I can do. Maybe I can mail you whats left if I can remove it in one piece. Thanks, Sharpie

[swyfor5]

Sharpie, I'll take those wheel tubs! PM me shipped price to 49665, and I'll get it right out to you.

[sharpie1972]

Sounds good, You'll like em! I'll get an exact shipping quote tomorrow. PM me your address again. Thanks, Sharpie

[swyfor5]

Man, I am drooling over that floor! Too bad we are so far apart! Someone closer better snatch that one up. Sharpie, you got the goods!

[sharpie1972]

Hey Bryan, meet me in Fargo and save shipping on the wheel wells! This Blazer had 12k on it when it was wrecked. This floor is beyond description, somebody is going to be very happy..... OK, I'll get the shipping quote and send the low mile wheel wells your way. Thanks again to a gracious repeat customer! Sharpie

[swyfor5]

Thank's for the offer, but work, work, work, here. That is a really nice looking floor, I feel lucky just to pick up the tubs, nice price too! By the way dropping the 1 ton axles in my K5 soon, and swapping in that NP205 t-case I picked up from ya a while back! Thank's a lot!

[swyfor5]

Hey Sharpie, off topic, but looking to replace some of my front floorboards, do you have any good floor steel I could weld in? Mainly drivers side, but both sides are pretty rotted out. Thank's, Bryan.

[sharpie1972]

Hi Bryan, not cutting up any cabs with minty floors at the moment. I'll let you know if I get a "tree victim" though. Let me know when the tubs arrive! Later, Sharpie

[Liddy71]

is the back cross member the same as a truck

[sharpie1972]

Good question. The Blazer floor are pretty unique but that area does look the same as a truck. Sharpie

[swyfor5]

Hey, Sharpie, Tubs arrived today, and as alway's, I am a happy man! They are sweet! Thank you SIR! Very nice shipping setup, also! Man, I couldn't be happier with these! SUPER! Thank's for the message about the floors, let me know if you find some metal I can use here, Thank's again, Bryan!

[sharpie1972]

Glad they arrived safely! Later, Sharpie

[swyfor5]

Sharpie, put me first in line for that floor! I'm just concerned with shipping costs, as funds are tight right now. I can't believe someone hasen't jumped on this. I love the tubs, and tore my whole rear end area apart today, and it is needing a lot more than I thought. Any ideas on shipping costs? Thank's, Bryan.

[69-72]

Happen to have a single wall top that could make its way to Fargo?

[sharpie1972]

Hi Bryan, I can research freight costs, I would build a sturdy crate for the floor. I will try to get an accurate weight on it. I'm guessing in the $400-500 range for freight, might be less if we could find a board member or transporter coming your way with room. I know a transporter out of Indiana that I will check on. Thanks, Sharpie

69-72: I've got a beatiful single wall top that would love to go on a road trip! Pics attached. $700 delivered to Fargo. Thanks, Sharpie

[sharpie1972]

a few more

[69-72]

Originally Posted by Liddy71

is the back cross member the same as a truck

I have converted a LWB truck bed to a Blazer bed and yes the back cross member is the same as a truck, expect if the Blazer is a 72 then there were two cut outs that the frame passes over. Easily fixed if you are handy with metal working.

[swyfor5]

Thank's Sharpie. I might have jumped the gun a little, like I said, funds are tight right now. Let me know what you come up with, but if you get any buy it now offers, I understand fully. Don't let me stop you from selling sooner. Thank's, Bryan.

[sharpie1972]

Hi Bryan, no problem. Sharpie