The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Racing and high performance (trucks haulin more than hay)

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 07-31-2010, 03:20 PM   #1
gene_ensor
Registered User
 
gene_ensor's Avatar
 
Join Date: Oct 2005
Location: Rapid City South Dakota
Posts: 39
15 x 14 Rims 10" back spacing?

Hello again friends. Can someone provide a good source for low budget 15x14 rims with custom back spacing? Currently my axles are 6 lug 1969 vintage trailing arm. Any additional comments on clearances, best brake line re-route fix, and e-brake setup would be appreciated. I would also entertain some mockup rims prior to blowing the budget on a narrowed axle. Thanks.

Info collected via multiple threads:

Wheel mating surface to WMS 12 bolts
1967-1970 62" 6 bolt (conversion to 5 bolt CPP, ECE or Summit)
1971-1972 63.5" 5 bolt
1973-? unknown 5 bolt

User width rim / tire / back spacing
prostreetC-10 62" 15x14 18.5 8.75 bs
SCOTI 62" 15x14 18.5 9.50 bs
.............. 15x14 10.00 bs possible

Comment: Remove the rear bumpstop + bracket on the outside of the frame. Cut the bedfloor to clear & stretch those tubs! On a coil/trailing-arm truck you can fit a 15x14" wheel w/10" of back spacing & not hit the frame rail. The wheel tubs in the bed only need to be enlarged as big as the tire. I had Mickey Thompson 31x18.5x15's on widened/custom offset corvette ralleys w/the above spacing on my 67 short fleet w/a stock length truck 12bolt rear end. This all depends on the relationship between rear-end & trailing arms not being altered (no lowering blocks).

1968SWBBigBlock 62"? 15x14.5 8.75 bs

Comment: I am running a standard 1968 width axle, using 18.5" wide Hoosier pro street radials Floor of the bed is cut back flush with the frame rail Wheel tubs widened accordingly I changed the springs over to a non tapered style similar to what is on the front suspension - you will not have enough room for a tapered spring (if you do not mind I would suggest just welding on spring perch's and using coil over set closer to the center of the truck, adjustable for ride height and dampening) Wheels are -offset by 8.75" (I would only go 8.25" next time - I think I can push 1/2" + into the wheel well without issue but I am to close to the ebrake line and had to build brackets to pull them away from the wheels to keep them from rubbing

70C10 Custom 29x18.5x15 Hoosiers 3.5"bs

Comment: 1.5" clearance on the frame rails and 1" clearance on the outer fender lip.

QKENUF4U 63.5" 15x14 rims w/ 10" bs 31x18.5x15 tires

Comment: stock frame/suspension only problem i ran into was balancing the tires. The machines don’t have a long enough arm.. could balance on a bubble balancer though.
gene_ensor is offline   Reply With Quote
Reply

Bookmarks

Tags
backspacing, drag, prostreet


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:21 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com