Bolt-in LOW HUMP??? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Chevy4Life** · 07-20-2003, 12:55 AM

My 67' has a HIGH HUMP cab. I want to convert it to a low hump, and recently read that SOME 2wd blazers had a bolt-in LOW HUMP, does that hump fit the trucks?

**FRENCHBLUE72** · 07-20-2003, 01:14 AM

Why do you want to convert??? It make's it easy for tranny work.
Just my 2 cent's worth.

**Chevy4Life** · 07-20-2003, 01:31 AM

I just like the flatter floor, and it will get some kind of bench seat so the more leg room the better.

**Chevy4Life** · 07-20-2003, 01:34 AM

Also, if it means cutting out the high hump and welding in a low hump I may just keep it the way it is. But if I could just bolt-in a low hump and find one I will definately do that.

crazy longhorn · 07-20-2003, 09:29 AM

I dont think you will find a bolt in low hump, all i have seen were a pc of the floor. You may be able to set up a bolt in low hump, if you cut the hump from a donor cab + a little extra floor to trim to fit. just trim to fit, & drill the holes? Good luck,crazyL

jay-dawg · 07-20-2003, 01:17 PM

my thoughts exactly

07-20-2003, 12:55 AM	#1
Chevy4Life Senior Member Join Date: Feb 2003 Location: Las Vegas, NV Posts: 750	Bolt-in LOW HUMP??? My 67' has a HIGH HUMP cab. I want to convert it to a low hump, and recently read that SOME 2wd blazers had a bolt-in LOW HUMP, does that hump fit the trucks?

07-20-2003, 01:14 AM	#2
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,604	Why do you want to convert??? It make's it easy for tranny work. Just my 2 cent's worth. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

07-20-2003, 09:29 AM	#5
crazy longhorn Fabricate till you "puke" Join Date: Jun 2002 Location: Ill Posts: 9,403	I dont think you will find a bolt in low hump, all i have seen were a pc of the floor. You may be able to set up a bolt in low hump, if you cut the hump from a donor cab + a little extra floor to trim to fit. just trim to fit, & drill the holes? Good luck,crazyL __________________ 69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears....

07-20-2003, 01:17 PM	#6
jay-dawg chevelito Join Date: Jun 2001 Location: Honolulu, HI USA Posts: 1,609	my thoughts exactly __________________ New deadline...when my son can drive. Aloha from Honolulu, HI

07-20-2003, 01:31 AM	#3
Chevy4Life Senior Member Join Date: Feb 2003 Location: Las Vegas, NV Posts: 750	I just like the flatter floor, and it will get some kind of bench seat so the more leg room the better.

07-20-2003, 01:34 AM	#4
Chevy4Life Senior Member Join Date: Feb 2003 Location: Las Vegas, NV Posts: 750	Also, if it means cutting out the high hump and welding in a low hump I may just keep it the way it is. But if I could just bolt-in a low hump and find one I will definately do that.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.