TX WTB: Spindle for Dana 44, 3/4ton 4x4/open knuckle - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**botmfedr1** · 09-08-2011, 05:19 PM

As the title says... i am helping a brother/truck owner find a drivers side, spindle for a Dana 44, open knuckle. I'm not an axle expert, so any help would be greatly appreciated.

shipping would be to 78550, money order is probably the best way for him to pay for it.

Let me know what you have.

thanks.
Mondo

*mrdana60* · 09-08-2011, 07:30 PM

i got one with the big bearings ?

**botmfedr1** · 09-08-2011, 09:26 PM

i know these pics probably wont help much, but i can't get any pics until tomorrow...

Name: spindle.jpg
Views: 102
Size: 76.2 KB

Name: spindle2.jpg
Views: 100
Size: 64.0 KB

**special-K** · 09-09-2011, 09:33 AM

So this is for a '70? I'm not sure if that spindle is the same as for discs used 71-1st design '72. I know it's necessary to give the axle number (front of long tube) with the '72s. Maybe someone else will know for sure if the first disc spindle is the same. My guess is yes.

junkcarguy · 09-25-2011, 09:18 PM

you need the hub not the spindle the hub holds the larger/outer part of the bearing the spindle is held on by 5 or 6 3/8th inch bolts its drum only or disk only for the hub i can get one here in co for 15.00+ ship if need be

09-08-2011, 05:19 PM	#1
botmfedr1 Senior Member Join Date: Feb 2008 Location: Harlingen, TX Posts: 1,097	WTB: Spindle for Dana 44, 3/4ton 4x4/open knuckle As the title says... i am helping a brother/truck owner find a drivers side, spindle for a Dana 44, open knuckle. I'm not an axle expert, so any help would be greatly appreciated. shipping would be to 78550, money order is probably the best way for him to pay for it. Let me know what you have. thanks. Mondo

09-08-2011, 07:30 PM	#2
mrdana60 Account Suspended Join Date: Sep 2010 Location: centre al Posts: 2,472	Re: WTB: Spindle for Dana 44, 3/4ton 4x4/open knuckle i got one with the big bearings ?

09-08-2011, 09:26 PM	#3
botmfedr1 Senior Member Join Date: Feb 2008 Location: Harlingen, TX Posts: 1,097	Re: WTB: Spindle for Dana 44, 3/4ton 4x4/open knuckle i know these pics probably wont help much, but i can't get any pics until tomorrow...

09-09-2011, 09:33 AM	#4
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,859	Re: WTB: Spindle for Dana 44, 3/4ton 4x4/open knuckle So this is for a '70? I'm not sure if that spindle is the same as for discs used 71-1st design '72. I know it's necessary to give the axle number (front of long tube) with the '72s. Maybe someone else will know for sure if the first disc spindle is the same. My guess is yes. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

09-25-2011, 09:18 PM	#5
junkcarguy Registered User Join Date: Sep 2011 Location: colorado springs colorado Posts: 49	Re: WTB: Spindle for Dana 44, 3/4ton 4x4/open knuckle you need the hub not the spindle the hub holds the larger/outer part of the bearing the spindle is held on by 5 or 6 3/8th inch bolts its drum only or disk only for the hub i can get one here in co for 15.00+ ship if need be



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.