Need help on something! - The 1947 - Present Chevrolet & GMC Truck Message Board Network

62 Barnfind · 03-09-2012, 08:52 PM

When I removed my front end I thought that I would remember where everything went. Does anybody know where these brackets go? I also replaced my fenders. It is pushed up as far as it can go and the right door is rubbing. Everything is loose but I can't seem to adjust it right.

sigshooter · 03-09-2012, 10:12 PM

the triangle brackets with the two slotted holes side by side go on the top of the fender and seal the fender and Cowl area . The two longer brackets with bolt holes in each end go from the header panel or grille support to the rad support

62 Barnfind · 03-09-2012, 10:36 PM

Thanks,
Do you have any pics?

sigshooter · 03-09-2012, 11:15 PM

I can get ya some tomorrow..... wedge piece top back part of fender under the cowl corner, fits perfect to the shape of the cab..... Long piece about the frame horn area ( bumper mounting area ), from the header panel to bottom of rad support.. should be holes in each for this.

I will get ya pics tomorrow

**aerotruk63** · 03-10-2012, 08:09 AM

**aerotruk63** · 03-10-2012, 08:11 AM

Year specific, sorry.

62 Barnfind · 03-10-2012, 10:21 AM

Thanks!

rbar · 03-10-2012, 11:02 AM

As for the fender rubbing, if thats an aftermarket fender, it's likely the bolt holes and the rear mounting hole are not in the right spot, mine weren't. The fender was even 1/4" shorter than stock.
Posted via Mobile Device

sigshooter · 03-10-2012, 11:50 AM

As promised, here are the pics

long pieces should be no problem with the pics
wedge pieces will not have the holes in the top of the fender if your using new fenders

sigshooter · 03-10-2012, 11:58 AM

body mounts will make a HUGE difference in how your body gaps are. If you use new rad support mounts and old cab mounts or visa versa new cab mounts and old rad mounts. Even just old mounts all together. It looks like your fenders are closer at the bottom andwider at the top. This looks like collapsed front cab mounts, replace the mounts. You could even add shims to the front cab mounts to bring it up. Play around with this... use a jack and loosen the front cab mounts and raise it up and see what that does to your gap.

After looking again, it looks closer at the bottom ( hard to tell in the pic ) so work on the rad support mounts instead of the cab if this is the case.... Same procedure

03-09-2012, 08:52 PM	#1
62 Barnfind Registered User Join Date: Jan 2012 Location: Killeen, Tx Posts: 1,354	Need help on something! When I removed my front end I thought that I would remember where everything went. Does anybody know where these brackets go? I also replaced my fenders. It is pushed up as far as it can go and the right door is rubbing. Everything is loose but I can't seem to adjust it right.

03-09-2012, 10:12 PM	#2
sigshooter Registered User Join Date: Aug 2011 Location: Tahlequah, Ok Posts: 1,235	Re: Need help on something! the triangle brackets with the two slotted holes side by side go on the top of the fender and seal the fender and Cowl area . The two longer brackets with bolt holes in each end go from the header panel or grille support to the rad support __________________ 1965 long bed ( grandpas old truck ) 1964 long bed BBW Custom Cab 1966 Short stepside 1964 long bed 1965 long bed Custom Cab, factory air, V-8, powerglide

03-09-2012, 10:36 PM	#3
62 Barnfind Registered User Join Date: Jan 2012 Location: Killeen, Tx Posts: 1,354	Re: Need help on something! Thanks, Do you have any pics?

03-09-2012, 11:15 PM	#4
sigshooter Registered User Join Date: Aug 2011 Location: Tahlequah, Ok Posts: 1,235	Re: Need help on something! I can get ya some tomorrow..... wedge piece top back part of fender under the cowl corner, fits perfect to the shape of the cab..... Long piece about the frame horn area ( bumper mounting area ), from the header panel to bottom of rad support.. should be holes in each for this. I will get ya pics tomorrow __________________ 1965 long bed ( grandpas old truck ) 1964 long bed BBW Custom Cab 1966 Short stepside 1964 long bed 1965 long bed Custom Cab, factory air, V-8, powerglide

03-10-2012, 08:09 AM	#5
aerotruk63 Check The Champ, Demonstrator Join Date: Jun 2009 Location: Montreal,Quebec Posts: 6,627	Re: Need help on something!

03-10-2012, 08:11 AM	#6
aerotruk63 Check The Champ, Demonstrator Join Date: Jun 2009 Location: Montreal,Quebec Posts: 6,627	Re: Need help on something! Year specific, sorry.

03-10-2012, 10:21 AM	#7
62 Barnfind Registered User Join Date: Jan 2012 Location: Killeen, Tx Posts: 1,354	Re: Need help on something! Thanks!

03-10-2012, 11:02 AM	#8
rbar Registered User Join Date: Nov 2010 Location: Meridian, Idaho Posts: 422	Re: Need help on something! As for the fender rubbing, if thats an aftermarket fender, it's likely the bolt holes and the rear mounting hole are not in the right spot, mine weren't. The fender was even 1/4" shorter than stock. Posted via Mobile Device __________________ 1963 Chevy stepside 327 1965 Chevy swb 383 1996 Mystic Mustang Cobra 2009 Pontiac G8 GXP 415hp/415tq 6speed

03-10-2012, 11:50 AM	#9
sigshooter Registered User Join Date: Aug 2011 Location: Tahlequah, Ok Posts: 1,235	Re: Need help on something! As promised, here are the pics long pieces should be no problem with the pics wedge pieces will not have the holes in the top of the fender if your using new fenders Attached Images __________________ 1965 long bed ( grandpas old truck ) 1964 long bed BBW Custom Cab 1966 Short stepside 1964 long bed 1965 long bed Custom Cab, factory air, V-8, powerglide

03-10-2012, 11:58 AM	#10
sigshooter Registered User Join Date: Aug 2011 Location: Tahlequah, Ok Posts: 1,235	Re: Need help on something! body mounts will make a HUGE difference in how your body gaps are. If you use new rad support mounts and old cab mounts or visa versa new cab mounts and old rad mounts. Even just old mounts all together. It looks like your fenders are closer at the bottom andwider at the top. This looks like collapsed front cab mounts, replace the mounts. You could even add shims to the front cab mounts to bring it up. Play around with this... use a jack and loosen the front cab mounts and raise it up and see what that does to your gap. After looking again, it looks closer at the bottom ( hard to tell in the pic ) so work on the rad support mounts instead of the cab if this is the case.... Same procedure __________________ 1965 long bed ( grandpas old truck ) 1964 long bed BBW Custom Cab 1966 Short stepside 1964 long bed 1965 long bed Custom Cab, factory air, V-8, powerglide



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.