|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
11-16-2012, 04:43 PM
|
#1 |
|
Registered User
Join Date: Sep 2009
Location: east tennessee
Posts: 158
|
Which block hugger headers aree you using?
Looks like I am going to have to use block hugger headers on my 5.3 AD with C4 front end. I have 3 sets of manifolds and C5 worked until I ran my brake lines now they are to close for my likeing. What is a good fitting brand to use?
|
|
|
|
11-16-2012, 07:42 PM
|
#2 |
|
Senior Member
Join Date: May 2009
Location: Fort Worth, TX
Posts: 6,370
|
Re: Which block hugger headers aree you using?
Why not just reroute the brake lines?
|
|
|
|
|
11-16-2012, 08:12 PM
|
#3 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,403
|
Re: Which block hugger headers aree you using?
2nd that, but we all know that a pic is worth 1000 words
 crazyl
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
|
|
|
|
11-16-2012, 10:55 PM
|
#4 |
|
1965 Chevy C10, 2005 4.8L/4l60
 
Join Date: Aug 2004
Location: DFW Texas
Posts: 8,540
|
Re: Which block hugger headers aree you using?
I used Sanderson CSLS1 shorties
Posted via Mobile Device
__________________
Clyde65 Rebuild of Clyde http://67-72chevytrucks.com/vboard/s...84#post8338184 69 Aristocrat Lo Liner build http://67-72chevytrucks.com/vboard/s...84#post7561684  support our troops! |
|
|
|
|
11-17-2012, 12:20 PM
|
#5 | |
|
Registered User
Join Date: Sep 2009
Location: east tennessee
Posts: 158
|
Re: Which block hugger headers aree you using?
Quote:
|
|
|
|
|
|
11-18-2012, 08:48 PM
|
#6 |
|
Registered User
Join Date: Sep 2012
Location: Milwaukie OR
Posts: 135
|
Re: Which block hugger headers aree you using?
I used Hooker block huggers, They are a universal application header for no specific vehicle, with tight clearance set ups. Center dump, and they come out parallel and slightly pointed in at the top of the oil pan. Only about $240, I used them because I was concerned with the stock z-bar clutch linkage that I decided to stay with. They come very close to the back of the starter, but will work fine. I still am awaiting exhaust from there on out.
|
|
|
|
|
11-21-2012, 10:32 PM
|
#7 |
|
Registered User
Join Date: Sep 2012
Location: Milwaukie OR
Posts: 135
|
Re: Which block hugger headers aree you using?
Hooker #2312
|
|
|
|
|
11-22-2012, 12:19 PM
|
#8 |
|
Registered User
Join Date: Sep 2005
Location: sc
Posts: 1,203
|
Re: Which block hugger headers aree you using?
I will match that ebay price of $240 shipped if interested.
__________________
71 Cheyenne C10 LWB cam'd 6.0/T56 Swap |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
