Slosh Tubz new company project "Square Peg" frame laying 1987 GMC Jimmy - Page 92 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**67cheby** · 10-11-2013, 06:10 PM

They are made by Sisco's Fab, waiting for the ones we are going to use to get here now

rip2174 · 10-11-2013, 07:39 PM

Hmm. Got a hold of them today. Says they only have them for 73-80. What kind of mods need to be made to make them work?

jtp67-72 · 10-11-2013, 10:13 PM

Quote:

Originally Posted by rip2174

Hmm. Got a hold of them today. Says they only have them for 73-80. What kind of mods need to be made to make them work?

That's the front end he's usin..........jim

**N2TRUX** · 10-13-2013, 12:19 PM

Quote:

Originally Posted by 67cheby

They are made by Sisco's Fab, waiting for the ones we are going to use to get here now

Mike I saw the hinges on their F/B page. It doesnt show or say much about them other than the few pics there. Do they use a strut or a prop? Can you show a pic of them mounted?

**screaminchevypickup** · 10-13-2013, 01:17 PM

Quote:

Originally Posted by N2TRUX

Mike I saw the hinges on their F/B page. It doesnt show or say much about them other than the few pics there. Do they use a strut or a prop? Can you show a pic of them mounted?

These are just the mock up set I have here at my shop but they just fold over on its pivot point and holds the hood open and they actually work pretty good..

**N2TRUX** · 10-14-2013, 02:14 PM

Quote:

Originally Posted by screaminchevypickup

These are just the mock up set I have here at my shop but they just fold over on its pivot point and holds the hood open and they actually work pretty good..

No fuss, no muss and it bolts in without cutting? Even better than using a strut since its cleaner and cheaper. Do you think it would be an issue with gusty winds causing them to close?

**67cheby** · 10-12-2013, 10:35 AM

That is correct , I am using the early front end and no mods they just bolt in the factory bolt holes

rip2174 · 10-12-2013, 10:43 AM

So an 87 cab. Older front clip. Don't the older hinges go down into the cowl part of the cab. The 81 and up hinges bolt directly to the fender. Im asking cause I have an 83 and trying to figure out my options for the hinges.

jlsanborn · 10-12-2013, 11:13 AM

The earlier ones bolt to the fenders too. They just use that big-o coil spring.

Low Elco · 10-12-2013, 01:06 PM

Dude, there's always Kickstarter. How many private cats can say they've had 2 inside cars at sema at the same time? Can ES kick in?

**screaminchevypickup** · 10-12-2013, 04:56 PM

Started polishing out pegs top today.. I think it'll work!

lowrodderchev · 10-12-2013, 07:55 PM

Quote:

Originally Posted by screaminchevypickup

Started polishing out pegs top today.. I think it'll work!

were is it? all I see is a pool of still water

**superflysteiny** · 10-13-2013, 12:31 AM

Quote:

Originally Posted by screaminchevypickup

Started polishing out pegs top today.. I think it'll work!

What paper did you stop with before you buffed it

**screaminchevypickup** · 10-13-2013, 01:13 PM

Quote:

Originally Posted by superflysteiny

What paper did you stop with before you buffed it

It was hard blocked with 1000 grit then on a medium block hit with 1500 and 2000 grit.. Then just to make buffing easier on a DA with a interface pad I run 3000 and 5000 grit over it..

mcbassin · 10-14-2013, 04:09 PM

Quote:

Originally Posted by screaminchevypickup

Started polishing out pegs top today.. I think it'll work!

That is samooth! Looks almost like black in the picture

Dinos63 · 10-14-2013, 07:02 PM

mike killer job brotha ! cant wait to see this bad boy

your wifes going to need a bodyguard when she drives it

Rusbuilt · 10-12-2013, 05:02 PM

Bling!! lol

babyblueoval · 10-12-2013, 06:26 PM

DAAYUUUMMM dude. That's amazing!!!

**oldman3** · 10-13-2013, 12:52 AM

That is so fine, great job...Jim

**screaminchevypickup** · 10-14-2013, 02:38 PM

Yes they are a bolt in hinge.. It would be really hard for the hold to blow shut because you have to give it a small lift to get it back past it's break over point..

**N2TRUX** · 10-14-2013, 03:24 PM

Sweet. Now if I can get the guys at Sisco's to respond I may have found a solution for my worn hinges.

**67cheby** · 10-15-2013, 09:32 AM

LOL, thanks Dino !

How about a little progress from last night we installed the Precision Products rebuilt wing windows and the Precision seals and gaskets ...TOP NOTCH !

Classic Parts of KC for the Side glasses (green tint)

Started laying out the wiring panel thanks to my wiring guru Brock Payton, Stephen Wright and Gary Angel, lots of top Notch wiring Painless Products, Dakota Digital, MSD Atomic Ingection

Stephen Wright installed the Specialty Power Window windshield wiper set up

BigDaddyV · 10-15-2013, 09:34 AM

Absolutely Gorgious! Killin it bro! Great Work!

**67cheby** · 10-15-2013, 09:34 AM

and Brock Payton rocking the KICKER install !

I have tons of pictures of the Interior from Stitch Interiors (Chuck Bench) but cant figure out how to load them , as soon as I can get some with my camera I will get them loaded he is KILLING the interior !

BigDaddyV · 10-15-2013, 09:35 AM

Agreed! Chuck is the Man! And those Subs sit perfectly in that corner!

10-11-2013, 06:10 PM	#1
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: Slosh Tubz new company project "Square Peg" frame laying 1987 GMC Jimmy They are made by Sisco's Fab, waiting for the ones we are going to use to get here now __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

10-11-2013, 07:39 PM	#2
rip2174 Registered User Join Date: Apr 2013 Location: wilmington nc Posts: 492	Re: Slosh Tubz new company project "Square Peg" frame laying 1987 GMC Jimmy Hmm. Got a hold of them today. Says they only have them for 73-80. What kind of mods need to be made to make them work?

10-12-2013, 10:35 AM	#7
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: Slosh Tubz new company project "Square Peg" frame laying 1987 GMC Jimmy That is correct , I am using the early front end and no mods they just bolt in the factory bolt holes __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

10-12-2013, 10:43 AM	#8
rip2174 Registered User Join Date: Apr 2013 Location: wilmington nc Posts: 492	Re: Slosh Tubz new company project "Square Peg" frame laying 1987 GMC Jimmy So an 87 cab. Older front clip. Don't the older hinges go down into the cowl part of the cab. The 81 and up hinges bolt directly to the fender. Im asking cause I have an 83 and trying to figure out my options for the hinges.

10-12-2013, 11:13 AM	#9
jlsanborn Registered User Join Date: Jun 2011 Location: Spokane, WA Posts: 2,367	Re: Slosh Tubz new company project "Square Peg" frame laying 1987 GMC Jimmy The earlier ones bolt to the fenders too. They just use that big-o coil spring. __________________ '77 K30 3+3 - "The Crummy" http://67-72chevytrucks.com/vboard/s...d.php?t=640134 '67 C10 L/SWB - Soon to be daily driver! http://67-72chevytrucks.com/vboard/s...d.php?t=471776

10-12-2013, 01:06 PM	#10
Low Elco Registered User Join Date: Apr 2003 Location: Indep, MO Posts: 5,893	Re: Slosh Tubz new company project "Square Peg" frame laying 1987 GMC Jimmy Dude, there's always Kickstarter. How many private cats can say they've had 2 inside cars at sema at the same time? Can ES kick in? __________________ Boppa's Old Yeller Truck Build, Old Yeller's New Heart! Project Buzz Bomb Flyin' Low!

10-12-2013, 04:56 PM	#11
screaminchevypickup Laid Back Join Date: Apr 2010 Location: mcloud ok Posts: 2,658	Re: Slosh Tubz new company project "Square Peg" frame laying 1987 GMC Jimmy Started polishing out pegs top today.. I think it'll work! Attached Images __________________ 72 chevy swb Direct dealers for.. Vintage Air, Porterbuilt, Billet Specialties,Budnik wheels ,eddie motorsports, raceline wheels, intro wheels, Dakota Digital, precision, unisteer, Trimparts, and many many more... Laid Back Recreations.. Full restoration shop and full paint and body.. Kyle http://67-72chevytrucks.com/vboard/s...d.php?t=574629

10-14-2013, 07:02 PM	#16
Dinos63 chevy only Join Date: Sep 2006 Location: Phoenix, AZ Posts: 6,619	Re: Slosh Tubz new company project "Square Peg" frame laying 1987 GMC Jimmy mike killer job brotha ! cant wait to see this bad boy your wifes going to need a bodyguard when she drives it __________________ CHEVY ONLY... Nothin Else !

10-12-2013, 05:02 PM	#17
Rusbuilt Registered User Join Date: Mar 2012 Location: Knoxville, TN Posts: 5,381	Re: Slosh Tubz new company project "Square Peg" frame laying 1987 GMC Jimmy Bling!! lol __________________ -Rus PLEASE HELP WITH PROJECT UNDERHAULINPaypal donations accepted @ rus1785@yahoo.com Rusbuilt's garage 1968 Chevy C-30 Darcy SOLD Rusbuilt shop truck *SOLD*

10-12-2013, 06:26 PM	#18
babyblueoval Registered User Join Date: Apr 2006 Location: Arkansas Posts: 835	Re: Slosh Tubz new company project "Square Peg" frame laying 1987 GMC Jimmy DAAYUUUMMM dude. That's amazing!!! __________________ Jim '71 Blazer-Porterbuilt Dropmember C4/LS1/6L80E '57 VW beetle - Oct. 2006 Hot VW's pg. 87 - 350hp intercooled, turbocharged, EFI 2.3liter and 5spd in the works '87 BMW 325i - daily driver

10-13-2013, 12:52 AM	#19
oldman3 Senior Member Join Date: Mar 2011 Location: West Plains, Missouri Posts: 7,555	Re: Slosh Tubz new company project "Square Peg" frame laying 1987 GMC Jimmy That is so fine, great job...Jim __________________ my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=459839 Jimbo's long bed step build:http://67-72chevytrucks.com/vboard/s...t=464626<br />

10-14-2013, 02:38 PM	#20
screaminchevypickup Laid Back Join Date: Apr 2010 Location: mcloud ok Posts: 2,658	Re: Slosh Tubz new company project "Square Peg" frame laying 1987 GMC Jimmy Yes they are a bolt in hinge.. It would be really hard for the hold to blow shut because you have to give it a small lift to get it back past it's break over point.. __________________ 72 chevy swb Direct dealers for.. Vintage Air, Porterbuilt, Billet Specialties,Budnik wheels ,eddie motorsports, raceline wheels, intro wheels, Dakota Digital, precision, unisteer, Trimparts, and many many more... Laid Back Recreations.. Full restoration shop and full paint and body.. Kyle http://67-72chevytrucks.com/vboard/s...d.php?t=574629

10-14-2013, 03:24 PM	#21
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,023	Re: Slosh Tubz new company project "Square Peg" frame laying 1987 GMC Jimmy Sweet. Now if I can get the guys at Sisco's to respond I may have found a solution for my worn hinges. __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra"

10-15-2013, 09:32 AM	#22
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: Slosh Tubz new company project "Square Peg" frame laying 1987 GMC Jimmy LOL, thanks Dino ! How about a little progress from last night we installed the Precision Products rebuilt wing windows and the Precision seals and gaskets ...TOP NOTCH ! Classic Parts of KC for the Side glasses (green tint) Started laying out the wiring panel thanks to my wiring guru Brock Payton, Stephen Wright and Gary Angel, lots of top Notch wiring Painless Products, Dakota Digital, MSD Atomic Ingection Stephen Wright installed the Specialty Power Window windshield wiper set up Attached Images __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

10-15-2013, 09:34 AM	#23
BigDaddyV Registered User Join Date: Mar 2013 Location: Grand Island, Ne. Posts: 1,110	Re: Slosh Tubz new company project "Square Peg" frame laying 1987 GMC Jimmy Absolutely Gorgious! Killin it bro! Great Work! __________________ *J. Vess, 6'6", Gearhead, Welder, Fabricator, Nutcase* 1955 Chevy Stepside "Dudley" My daily http://www.67-72chevytrucks.com/vboa...d.php?t=760288 1972 Chevy C10, Project "Chevro~Layed out" Nether Storm Build Thread http://67-72chevytrucks.com/vboard/s...23#post6007523



Register or Log In To remove these advertisements.

10-15-2013, 09:35 AM	#25
BigDaddyV Registered User Join Date: Mar 2013 Location: Grand Island, Ne. Posts: 1,110	Re: Slosh Tubz new company project "Square Peg" frame laying 1987 GMC Jimmy Agreed! Chuck is the Man! And those Subs sit perfectly in that corner! __________________ *J. Vess, 6'6", Gearhead, Welder, Fabricator, Nutcase* 1955 Chevy Stepside "Dudley" My daily http://www.67-72chevytrucks.com/vboa...d.php?t=760288 1972 Chevy C10, Project "Chevro~Layed out" Nether Storm Build Thread http://67-72chevytrucks.com/vboard/s...23#post6007523

Register or Log In To remove these advertisements.