Brave or crazy? crewcab build

[oilyrag80]

Got some more work on the bpillar done. latch area and upper part done, now I need to work on back side where the door seal rubber goes. Also at the bottom where it meets the rocker.

[oilyrag80]

Originally Posted by jbclassix

use 2 doors... it makes it easier. I used 2 doors to do the 4th on my suburban... my brothers truck will be made from 3 doors by the time I am done with fab.

I picked up a front driver side truck door still need a pass side door.
I should get two of each just to be safe!

[thelimoscott]

Any progress brother???

[thelimoscott]

Loving it!!! I've wanted to try it myself!!
Apologize for the any progress reply, didn't see the latest and greatest updates.
I'm a rookie to this site...

[oilyrag80]

Got some more work done today I worked on the rocker for the 4th door.
I used two new rockers to make one.I also worked on the back side of the b pillar I used the rear of the pass side b pillar off another sub. I flipped it upside down to fit also worked on upper door channel I used the same method on this area. Everthing is roughed in I wanted to get more done but it got late and I ran out of argon.

[Rusbuilt]

Lookin good though!!!

[ddubbs]

Man I have been keeping a eye on your build. Man luv what your doing. Great ideas and like the fourth door. Subscribed!!!!!
Posted via Mobile Device

[oilyrag80]

Originally Posted by Rusbuilt

Lookin good though!!!

Originally Posted by ddubbs

Man I have been keeping a eye on your build. Man luv what your doing. Great ideas and like the fourth door. Subscribed!!!!!
Posted via Mobile Device

Thanks for the feed back glad to know your following along.
Hopefully I can start work on the door soon

[oilyrag80]

Time for some door pics, after lots of measuring its time to cut up a super clean rust free arizona door. This door was coated with under coating on the inside so I had to strip some off so it would sit flush.

[oilyrag80]

Heres some more pics

[jbclassix]

This is the fun part!
Posted via Mobile Device

[Rusbuilt]

Oh man you are making it look easy!

[frostbyte]

Sweet, Your making great progress. Looks awesome.

[67cheby]

Killing it man !
Posted via Mobile Device

[Dinos63]

great job!!

[jbclassix]

Do you have your hinges attached in that picture?

[oilyrag80]

Originally Posted by jbclassix

Do you have your hinges attached in that picture?

No they are not door is just sitting there, its just held in by the latch.
It was getting late and I just had to check it out before I was done for the day.
The door fits in the hole but is nowhere near lining up, still have a little trimming
to do and alot of adjusting.

[oilyrag80]

Ok, I could not wait until the weekend I had to know if this was going to work.
I got home from work drilled a few holes, now I have a swinging 4th door.
Still needs alot of work and adjustment but it works and fits pretty good as well.

[Rusbuilt]

Wow bro! Looks great!

[jbclassix]

Did you move the hinges closer together like on the 3rd door?
Posted via Mobile Device

[oilyrag80]

Originally Posted by jbclassix

Did you move the hinges closer together like on the 3rd door?
Posted via Mobile Device

No I did not see any reason too, the hinge sits flush on b pillar and it clears the inner latch. I thought I'd give it a shot, seems to work ok.

[bodydropped68]

Looking awesome !!!!!!!!!!!!!!!
Posted via Mobile Device

[oilyrag80]

Originally Posted by jbclassix

Did you move the hinges closer together like on the 3rd door?
Posted via Mobile Device

Here is a pic of upper hinge before I drilled holes

[lolife99]

Amazing work!

[Xeen]

Impressive work man.