|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
02-27-2013, 09:33 PM
|
#1 |
|
Registered User
 
Join Date: Feb 2011
Location: North Texas
Posts: 118
|
Throttle cable question - 72 C20 402 cu.in.
Will the factory throttle cable and carb bracket still function correctly with an Edelbrock Performer PN7164 aluminum intake installed? I noticed the carb will be sitting quite a bit higher on the Performer compared to the OEM cast iron intake.
Pics would be ideal. Thanks in advance.
__________________
Jeff Horsman 1972 C20 Highlander "C" 1966 Olds 442 L69 four speed 1971 Skylark (GS clone racecar) 494 stroker 1986 Buick T-Type |
|
|
|
02-27-2013, 09:39 PM
|
#2 |
|
Proprietor of Dale's Corner
Join Date: Nov 2012
Location: Vacaville , CA
Posts: 16,011
|
Re: Throttle cable question - 72 C20 402 cu.in.
Should be enough slack,
__________________
"Some Days Chickens And Some Days Feathers" Dale XNGH ECV Sam Brannan 1004 R.I.P. 67ChevyRedneck R.I.P. Grumpy Old Man |
|
|
|
|
02-27-2013, 10:06 PM
|
#3 | |
|
Registered User
Join Date: Feb 2011
Location: North Texas
Posts: 118
|
Re: Throttle cable question - 72 C20 402 cu.in.
Quote:
I do not want to make the swap and find out that it does not reach or is binding. My worse fear is to take it back off after it is in the truck. Not a fan of just rigging something either. Hopefully someone on the board has one of these installed on their big block.
__________________
Jeff Horsman 1972 C20 Highlander "C" 1966 Olds 442 L69 four speed 1971 Skylark (GS clone racecar) 494 stroker 1986 Buick T-Type |
|
|
|
|
|
03-03-2013, 10:01 AM
|
#4 |
|
Registered User
Join Date: Feb 2011
Location: North Texas
Posts: 118
|
Re: Throttle cable question - 72 C20 402 cu.in.
TTT...anyone?
__________________
Jeff Horsman 1972 C20 Highlander "C" 1966 Olds 442 L69 four speed 1971 Skylark (GS clone racecar) 494 stroker 1986 Buick T-Type |
|
|
|
|
03-03-2013, 10:03 AM
|
#5 |
|
Proprietor of Dale's Corner
Join Date: Nov 2012
Location: Vacaville , CA
Posts: 16,011
|
Re: Throttle cable question - 72 C20 402 cu.in.
I still say it willwork
Posted via Mobile Device
__________________
"Some Days Chickens And Some Days Feathers" Dale XNGH ECV Sam Brannan 1004 R.I.P. 67ChevyRedneck R.I.P. Grumpy Old Man |
|
|
|
|
03-03-2013, 11:01 AM
|
#6 |
|
2WD Jimmy
Join Date: Mar 2005
Location: Davis County, Utah
Posts: 2,564
|
Re: Throttle cable question - 72 C20 402 cu.in.
I have a BB in the stock location. I am running a Holley on an Edelbrock Air Gap manifold. The stock cable had to be shortened about 2 inches. I'm using the stock bracket, but I had to grind on it a little. I don't think anyone could tell any modifications were made to this setup in order to get it to fit.
Posted via Mobile Device |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
