|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
08-24-2013, 09:10 PM
|
#1 |
|
Registered User
Join Date: Aug 2013
Location: waynesville georgia
Posts: 164
|
i have problems again clutch linkage question
i have v8 in my truck sbc and the bell crank also called z bar cracked (
 for those that don't know like me im talkin about bracket that bolts from frame to engine for clutch linkage) i have access to one off a straight 6 truck will it work
|
|
|
|
08-24-2013, 10:23 PM
|
#2 |
|
Registered User
Join Date: Jan 2013
Location: Mickleton, NJ
Posts: 1,776
|
Re: i have problems again clutch linkage question
It should. Only difference is in the brackets, z bars should all be the same.
__________________
Shawn 1970 Chevy C-10 SWB, 350, TKO 600 5 speed My build http://67-72chevytrucks.com/vboard/s...d.php?t=559881 |
|
|
|
|
08-24-2013, 10:30 PM
|
#3 |
|
Registered User
Join Date: Aug 2013
Location: Hiram Ohio
Posts: 619
|
Re: i have problems again clutch linkage question
they are the same
|
|
|
|
|
08-24-2013, 10:42 PM
|
#4 |
|
Watch out for your cornhole !
 
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
Re: i have problems again clutch linkage question
Six cylinder Z bars are longer between the frame and block pivot ball than small block ones by about 1/2 an inch.
Posted via Mobile Device |
|
|
|
|
08-24-2013, 11:45 PM
|
#5 |
|
Registered User
Join Date: Aug 2013
Location: waynesville georgia
Posts: 164
|
Re: i have problems again clutch linkage question
thinks was drivin home from work when clutch pedal quit pulled over in bad part of town and found it had cracked on the side so i didnt want to leave truck there so drove it home shifting it by rpms thats hard as hell doing that on a 3 speed truck on the column had to stop a few times shut it off and start again
|
|
|
|
|
08-25-2013, 06:55 AM
|
#6 |
|
Registered User
Join Date: Feb 2012
Location: Wisconsin
Posts: 144
|
Re: i have problems again clutch linkage question
I am doing a 6 cyl to 350 swap and am looking at a hydraulic clutch conversion.
|
|
|
|
|
08-25-2013, 09:34 AM
|
#7 |
|
2WD Jimmy
Join Date: Mar 2005
Location: Davis County, Utah
Posts: 2,563
|
Re: i have problems again clutch linkage question
[QUOTE=Tx Firefighter;6237130]Six cylinder Z bars are longer between the frame and block pivot ball than small block ones by about 1/2 an inch.
/QUOTE] And it would be suuper easy to cut that excess length off with a hacksaw. |
|
|
|
|
08-25-2013, 01:34 PM
|
#8 | |
|
Watch out for your cornhole !
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
Re: i have problems again clutch linkage question
[quote=Tom Vogel;6237563]
Quote:
Posted via Mobile Device |
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
