70 C10 disc brake conversion help needed - The 1947 - Present Chevrolet & GMC Truck Message Board Network

briscuba · 04-02-2014, 02:30 PM

Hi,
I have a stock 1970 CST/10 big block. Awesome motor, but heavy for braking! I need to put disc brakes on it.

I just picked up a front end clip from a "Heavy Half" 1995 blazer. I believe it is known as "Heavy Half" anyways, and does have the 6 lugs. The "A" arms look different, prob. won't work, but will the spindles and disc brakes?

Does anyone know if this clip can help me at all?

Thanks!

brad_man_72 · 04-02-2014, 03:44 PM

Probably not. After all of the machine work and custom parts it would be cheaper to buy a kit.
There's a faq section on disc brake swap questions showing the stuff that interchanges between 64-88

TwinsSpeedShop · 04-02-2014, 04:07 PM

Don't do it!! I used 88-98 spindles and there are alignment problems and after rebuilding all the parts that needed it, I wish I would have just bought the kit. You will brake even or come out ahead if you buy the kit and have far less headaches

**steelhorse** · 04-02-2014, 05:04 PM

If you want to use factory spindles you can use the 73-87 but they will take you to 5 lug. you will also need to use the ball joints and tie rod from they same years.

SS Tim · 04-02-2014, 05:04 PM

http://67-72chevytrucks.com/vboard/s...68&postcount=4

hugger6933 · 04-02-2014, 08:13 PM

You can use all gm stuff like the 6 lug rotors and spindles and the 68 lower control arms use the newer ball joints and tie rods and then the calipers and all of the stuff will work. But I have gathered all of these parts well just from not throwing junk away cause I have a 95 3/4 ton that I junked and had the whole front suspension. the problem is when you build the truck it all looks and fits together real good and everything gives you a warm and fuzzy feeling then when you get farther along on the project and get it on the road, take it to get a front end aliginment it can't be done it is too far out of spec to get close with shims. Nobody on here that I have heard of that has used this set up has been able to get the steering lined out that I know of, it may have happened while I was sleeping but I just think your better with some aftermarket of the shelf stuff.

briscuba · 04-06-2014, 04:07 PM

Thanks guys, really pleases with your responses and this forum. No need to reinvent the wheel when thousand have already gone through all of this.

Thanks again!
Brian

04-02-2014, 02:30 PM	#1
briscuba Registered User Join Date: Apr 2014 Location: Thousand Oaks, CA Posts: 118	70 C10 disc brake conversion help needed Hi, I have a stock 1970 CST/10 big block. Awesome motor, but heavy for braking! I need to put disc brakes on it. I just picked up a front end clip from a "Heavy Half" 1995 blazer. I believe it is known as "Heavy Half" anyways, and does have the 6 lugs. The "A" arms look different, prob. won't work, but will the spindles and disc brakes? Does anyone know if this clip can help me at all? Thanks!

04-02-2014, 03:44 PM	#2
brad_man_72 the boat guy Join Date: Jul 2007 Location: springfield mo Posts: 2,339	Re: 70 C10 disc brake conversion help needed Probably not. After all of the machine work and custom parts it would be cheaper to buy a kit. There's a faq section on disc brake swap questions showing the stuff that interchanges between 64-88 __________________ 67, swb, fleet, tach, throttle, 5.3, 4l60e, 3.73's, fuel cell, 5 lug, p.d.b., 4-6 drop. great little truck 66, stevens drag/ski 18' silouette, 350, 2.02 doublehump heads. comp extreme marine 278 cam, vette 7 fin valve covers, old polished edelbrock intake, velvetdrive, casale v-drive, adj cavitation plate. 28, model a rpu project,

04-02-2014, 04:07 PM	#3
TwinsSpeedShop Registered User Join Date: Mar 2014 Location: Easley SC Posts: 150	Re: 70 C10 disc brake conversion help needed Don't do it!! I used 88-98 spindles and there are alignment problems and after rebuilding all the parts that needed it, I wish I would have just bought the kit. You will brake even or come out ahead if you buy the kit and have far less headaches

04-02-2014, 05:04 PM	#4
steelhorse Senior Member Join Date: Apr 2008 Location: Franklinton NC Posts: 1,309	Re: 70 C10 disc brake conversion help needed If you want to use factory spindles you can use the 73-87 but they will take you to 5 lug. you will also need to use the ball joints and tie rod from they same years.

04-02-2014, 05:04 PM	#5
SS Tim Registered User Join Date: Aug 2010 Location: Edwards, CA Posts: 7,503	Re: 70 C10 disc brake conversion help needed http://67-72chevytrucks.com/vboard/s...68&postcount=4 __________________ Thanks, Tim * VIN/Model Decoders * Power Team Charts (engine/transmission/gear ratio) * Post Your Pickup SPID Blazer SPID Suburban/Panel SPID * RTFM ... Read The Factory Manuals... download 'em here Highlanders Do you have a 1972 Plaid Pickup? Plaid Blazer ** Plaid Suburban

04-02-2014, 08:13 PM	#6
hugger6933 Registered User Join Date: Oct 2008 Location: Marianna Arkansas Posts: 7,279	Re: 70 C10 disc brake conversion help needed You can use all gm stuff like the 6 lug rotors and spindles and the 68 lower control arms use the newer ball joints and tie rods and then the calipers and all of the stuff will work. But I have gathered all of these parts well just from not throwing junk away cause I have a 95 3/4 ton that I junked and had the whole front suspension. the problem is when you build the truck it all looks and fits together real good and everything gives you a warm and fuzzy feeling then when you get farther along on the project and get it on the road, take it to get a front end aliginment it can't be done it is too far out of spec to get close with shims. Nobody on here that I have heard of that has used this set up has been able to get the steering lined out that I know of, it may have happened while I was sleeping but I just think your better with some aftermarket of the shelf stuff.

04-06-2014, 04:07 PM	#7
briscuba Registered User Join Date: Apr 2014 Location: Thousand Oaks, CA Posts: 118	Re: 70 C10 disc brake conversion help needed Thanks guys, really pleases with your responses and this forum. No need to reinvent the wheel when thousand have already gone through all of this. Thanks again! Brian



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.