PROJECT "As Seen In My Garage" - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Toxic Redline · 05-15-2011, 09:37 PM

Ok so i finally decided to do a build thread on here.

so a two years ago i bought a 1984 Chevrolet K20. 383 Stroker, Hooker Comp Headers, Edlebrock performer intake, 2 Inch body Lift, faded paint, minimal body cancer, 4x4, hi-flow water pump. I had always wanted a square body, my dad had some when i was younger but sold them before i was old enough to drive.

Soon after i got it and started body work

Toxic Redline · 05-15-2011, 09:42 PM

Next i started to do more body work and i primered the whole thing black for winter because i dont like body work in the cold

I put a 4 inch lift on for a total of 6 inches of lift. Then i started haveing clutch problems. i put a new clutch in and kept on ruining throwout bearings, after some research i found it needed a long shaft throw out bearing. I put one in and it worked. (tranny dropped 4 times by this point.

Toxic Redline · 05-15-2011, 09:47 PM

i traded for two new front fenders and started body work again. Then i started haveing motor issues. My harmonic dampner broke so i had to get a new one. those arent cheap. After that my timing kept on getting messed up, dont know why, then i started having issues with the rocker arms and heads,. i did not know what clearence they needed to be so before i ruined the whole motor i traded it for a 350 small block that would not need so much tlc and get better gas milage, by this point i decided i wanted a daily driver not a race truck.

Toxic Redline · 05-15-2011, 09:53 PM

that is my new motor and centerforce clutch. It took me awhile to get it together. (school and a little burned out) but i finally got her together and took her for a test drive...... and ruined a throwout bearing. so i got a new throwout bearing, and for some reason it is not working, i dont know what kind of tranny is in my truck but im done messing with it, so yesterday i pulled the body off my suburban (it had been rolled) and i am going to put that tranny in my truck, that way i know what exactly is in my truck and i dont have to play this dumb guessing game........

Toxic Redline · 05-15-2011, 09:55 PM

A side note dont buy the extended brake lines from Autozone because they dont stock them anymore and it takes them a month to tell you!!! fetching ridiculous!!

Toxic Redline · 05-18-2011, 11:39 AM

I've decided that i will use the transmission out of the burb because i will not have to play the guessing game and that tranny has the " Bulletproof" NP205 Transfer case that i have always wanted

Toxic Redline · 05-31-2011, 01:09 AM

pulled the tranny out of the burban and cleaned her all up and got her painted

30+ years of fossilized grease is now gone

looks pretty nice

Toxic Redline · 05-31-2011, 01:11 AM

after that i got the burb frame cut up and ready for the scrap yard

saving the axles and motor even though the motor needs a complete rebuild and almost everything,,,, might end up scrapping it for money

makman1297 · 05-31-2011, 01:57 AM

Looking good, i always liked the 3/4 tons better.

Toxic Redline · 06-02-2011, 07:36 PM

Got some 37" Wranglers just got done putting them on the rim, now to pay for balancing

jonesky2 · 06-10-2011, 10:04 PM

keep it up! I want to see this thing with the new shoes.

Toxic Redline · 06-13-2011, 05:25 PM

the new shoes not on yet cuz jones hasnt got me the hookup

Toxic Redline · 06-13-2011, 05:27 PM

Found a sweet tach instrument cluster

cant wait to get it in

Toxic Redline · 06-13-2011, 05:29 PM

it was all in one piece but im using some other guages for the amps and temp and the oil pressure

o and i set back the milage

now my truck has no miles on it

Toxic Redline · 06-17-2011, 09:19 PM

need a longer driveline!!

why do the junk yards bend all of them!!

Kapote · 04-13-2014, 01:38 AM

Ok we'll I'm formerly known as Toxic Redline but after being out of the country for two years I've started up my 84 project again' before I left I got rid of that 350 so it just didn't rot, so now I've been looking for a new motor but I ain't got no money, so I got a deal' a 64 dump truck that they put a crate 350 that has 70'000 on it now and I get it free I just have to put the trans in a different truck, so I dropped the trans and fired up the motor today needless to say IM PUMPED!!! Good to be back

Zane M · 04-13-2014, 10:25 AM

Looking forward to seeing some more progress.

rusty76 · 04-13-2014, 11:51 AM

I'll be watching along for the ride. Waitin on updates.......

Hankster · 04-13-2014, 09:52 PM

I'll be watching this one!

Kapote · 04-18-2014, 11:51 PM

Ok so the trans is out and motor is all loose except for the motor mounts hopefully I'll get the loader and pull the motor tomorrow !

**aotte1** · 04-19-2014, 09:29 AM

Very nice project, with lots of innovative work. Been to Ogden many times, great scenery, and better skiing, Powder Mountain

. Keep up the reports to us.
Do you have any " government liquidation" sales in your area, sometimes they have unique 4x4 stuff. We are driving a one ton 4x4 CUCV as HD truck which includes trail making through the woods, it is amazing how far you can go just crashing through the woods with it. Also have CUCV Blazer made from 6 parts blazers. They have cool things like M16 gun racks, black out lights, jerry can holders, spot lights, places for electronic gear, dual battery and alternator set-ups, and almost crash- proof bumpers.

Thanks for sharing your project with us. Please keep reporting.
Les

05-15-2011, 09:37 PM	#1
Toxic Redline Registered User Join Date: May 2010 Location: Ogden, Utah Posts: 219	PROJECT "As Seen In My Garage" Ok so i finally decided to do a build thread on here. so a two years ago i bought a 1984 Chevrolet K20. 383 Stroker, Hooker Comp Headers, Edlebrock performer intake, 2 Inch body Lift, faded paint, minimal body cancer, 4x4, hi-flow water pump. I had always wanted a square body, my dad had some when i was younger but sold them before i was old enough to drive. Soon after i got it and started body work Attached Images __________________ 84 K20 Long Box W.I.P 78 Burb - parts now [Rolled] 68 c20 dump bed WHEN IN DOUBT--- FLOOR IT

05-15-2011, 09:42 PM	#2
Toxic Redline Registered User Join Date: May 2010 Location: Ogden, Utah Posts: 219	Re: PROJECT "As Seen In My Garage" Next i started to do more body work and i primered the whole thing black for winter because i dont like body work in the cold I put a 4 inch lift on for a total of 6 inches of lift. Then i started haveing clutch problems. i put a new clutch in and kept on ruining throwout bearings, after some research i found it needed a long shaft throw out bearing. I put one in and it worked. (tranny dropped 4 times by this point. Attached Images __________________ 84 K20 Long Box W.I.P 78 Burb - parts now [Rolled] 68 c20 dump bed WHEN IN DOUBT--- FLOOR IT

05-15-2011, 09:47 PM	#3
Toxic Redline Registered User Join Date: May 2010 Location: Ogden, Utah Posts: 219	Re: PROJECT "As Seen In My Garage" i traded for two new front fenders and started body work again. Then i started haveing motor issues. My harmonic dampner broke so i had to get a new one. those arent cheap. After that my timing kept on getting messed up, dont know why, then i started having issues with the rocker arms and heads,. i did not know what clearence they needed to be so before i ruined the whole motor i traded it for a 350 small block that would not need so much tlc and get better gas milage, by this point i decided i wanted a daily driver not a race truck. Attached Images __________________ 84 K20 Long Box W.I.P 78 Burb - parts now [Rolled] 68 c20 dump bed WHEN IN DOUBT--- FLOOR IT

05-15-2011, 09:53 PM	#4
Toxic Redline Registered User Join Date: May 2010 Location: Ogden, Utah Posts: 219	Re: PROJECT "As Seen In My Garage" that is my new motor and centerforce clutch. It took me awhile to get it together. (school and a little burned out) but i finally got her together and took her for a test drive...... and ruined a throwout bearing. so i got a new throwout bearing, and for some reason it is not working, i dont know what kind of tranny is in my truck but im done messing with it, so yesterday i pulled the body off my suburban (it had been rolled) and i am going to put that tranny in my truck, that way i know what exactly is in my truck and i dont have to play this dumb guessing game........ Attached Images __________________ 84 K20 Long Box W.I.P 78 Burb - parts now [Rolled] 68 c20 dump bed WHEN IN DOUBT--- FLOOR IT

05-15-2011, 09:55 PM	#5
Toxic Redline Registered User Join Date: May 2010 Location: Ogden, Utah Posts: 219	Re: PROJECT "As Seen In My Garage" A side note dont buy the extended brake lines from Autozone because they dont stock them anymore and it takes them a month to tell you!!! fetching ridiculous!! __________________ 84 K20 Long Box W.I.P 78 Burb - parts now [Rolled] 68 c20 dump bed WHEN IN DOUBT--- FLOOR IT

05-18-2011, 11:39 AM	#6
Toxic Redline Registered User Join Date: May 2010 Location: Ogden, Utah Posts: 219	Re: PROJECT "As Seen In My Garage" I've decided that i will use the transmission out of the burb because i will not have to play the guessing game and that tranny has the " Bulletproof" NP205 Transfer case that i have always wanted __________________ 84 K20 Long Box W.I.P 78 Burb - parts now [Rolled] 68 c20 dump bed WHEN IN DOUBT--- FLOOR IT

05-31-2011, 01:09 AM	#7
Toxic Redline Registered User Join Date: May 2010 Location: Ogden, Utah Posts: 219	Re: PROJECT "As Seen In My Garage" pulled the tranny out of the burban and cleaned her all up and got her painted 30+ years of fossilized grease is now gone looks pretty nice Attached Images __________________ 84 K20 Long Box W.I.P 78 Burb - parts now [Rolled] 68 c20 dump bed WHEN IN DOUBT--- FLOOR IT

05-31-2011, 01:11 AM	#8
Toxic Redline Registered User Join Date: May 2010 Location: Ogden, Utah Posts: 219	Re: PROJECT "As Seen In My Garage" after that i got the burb frame cut up and ready for the scrap yard saving the axles and motor even though the motor needs a complete rebuild and almost everything,,,, might end up scrapping it for money __________________ 84 K20 Long Box W.I.P 78 Burb - parts now [Rolled] 68 c20 dump bed WHEN IN DOUBT--- FLOOR IT

05-31-2011, 01:57 AM	#9
makman1297 Registered User Join Date: Mar 2010 Location: Beaufort SC Posts: 583	Re: PROJECT "As Seen In My Garage" Looking good, i always liked the 3/4 tons better.

06-02-2011, 07:36 PM	#10
Toxic Redline Registered User Join Date: May 2010 Location: Ogden, Utah Posts: 219	Re: PROJECT "As Seen In My Garage" Got some 37" Wranglers just got done putting them on the rim, now to pay for balancing __________________ 84 K20 Long Box W.I.P 78 Burb - parts now [Rolled] 68 c20 dump bed WHEN IN DOUBT--- FLOOR IT

06-10-2011, 10:04 PM	#11
jonesky2 Registered User Join Date: Nov 2009 Location: Hooper Utah Posts: 224	Re: PROJECT "As Seen In My Garage" keep it up! I want to see this thing with the new shoes.

06-13-2011, 05:25 PM	#12
Toxic Redline Registered User Join Date: May 2010 Location: Ogden, Utah Posts: 219	Re: PROJECT "As Seen In My Garage" the new shoes not on yet cuz jones hasnt got me the hookup Attached Images __________________ 84 K20 Long Box W.I.P 78 Burb - parts now [Rolled] 68 c20 dump bed WHEN IN DOUBT--- FLOOR IT

06-13-2011, 05:27 PM	#13
Toxic Redline Registered User Join Date: May 2010 Location: Ogden, Utah Posts: 219	Re: PROJECT "As Seen In My Garage" Found a sweet tach instrument cluster cant wait to get it in Attached Images __________________ 84 K20 Long Box W.I.P 78 Burb - parts now [Rolled] 68 c20 dump bed WHEN IN DOUBT--- FLOOR IT

06-13-2011, 05:29 PM	#14
Toxic Redline Registered User Join Date: May 2010 Location: Ogden, Utah Posts: 219	Re: PROJECT "As Seen In My Garage" it was all in one piece but im using some other guages for the amps and temp and the oil pressure o and i set back the milage now my truck has no miles on it __________________ 84 K20 Long Box W.I.P 78 Burb - parts now [Rolled] 68 c20 dump bed WHEN IN DOUBT--- FLOOR IT

06-17-2011, 09:19 PM	#15
Toxic Redline Registered User Join Date: May 2010 Location: Ogden, Utah Posts: 219	Re: PROJECT "As Seen In My Garage" need a longer driveline!! why do the junk yards bend all of them!! __________________ 84 K20 Long Box W.I.P 78 Burb - parts now [Rolled] 68 c20 dump bed WHEN IN DOUBT--- FLOOR IT



Register or Log In To remove these advertisements.

04-13-2014, 01:38 AM	#16
Kapote Registered User Join Date: Dec 2013 Location: Ogden Utah Posts: 19	Re: PROJECT "As Seen In My Garage" Ok we'll I'm formerly known as Toxic Redline but after being out of the country for two years I've started up my 84 project again' before I left I got rid of that 350 so it just didn't rot, so now I've been looking for a new motor but I ain't got no money, so I got a deal' a 64 dump truck that they put a crate 350 that has 70'000 on it now and I get it free I just have to put the trans in a different truck, so I dropped the trans and fired up the motor today needless to say IM PUMPED!!! Good to be back Attached Images

04-13-2014, 10:25 AM	#17
Zane M Registered User Join Date: Dec 2006 Location: SLC, UT Posts: 706	Re: PROJECT "As Seen In My Garage" Looking forward to seeing some more progress.

04-13-2014, 11:51 AM	#18
rusty76 Registered User Join Date: Sep 2012 Location: Midway, NC Posts: 3,275	Re: PROJECT "As Seen In My Garage" I'll be watching along for the ride. Waitin on updates....... __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=581873 The low buck build threads. Check'em out! http://67-72chevytrucks.com/vboard/s...d.php?t=666022 My build thread Crossmembers CC

04-13-2014, 09:52 PM	#19
Hankster Registered User Join Date: Jan 2013 Location: Nacogdoches, Texas Posts: 895	Re: PROJECT "As Seen In My Garage" I'll be watching this one! __________________ Current Build 89 s10 ecsb 2wd 4.3/700r4 50k OG Miles Instagram- shaggin_s10 '86 Chevrolet C10 Custom Deluxe - Gen V 454 - 4l80e - welded 12 bolt (Build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=611611 ) SOLD

04-18-2014, 11:51 PM	#20
Kapote Registered User Join Date: Dec 2013 Location: Ogden Utah Posts: 19	Re: PROJECT "As Seen In My Garage" Ok so the trans is out and motor is all loose except for the motor mounts hopefully I'll get the loader and pull the motor tomorrow ! __________________ 1984 k20 "Project as seen in my garage". 1968 C20 -292 dump bed 1987 Burb, 350TBI 700R4, RedNRusty

04-19-2014, 09:29 AM	#21
aotte1 Registered User Join Date: Oct 2013 Location: lousiville Ky Posts: 2,649	Re: PROJECT "As Seen In My Garage" Very nice project, with lots of innovative work. Been to Ogden many times, great scenery, and better skiing, Powder Mountain. Keep up the reports to us. Do you have any " government liquidation" sales in your area, sometimes they have unique 4x4 stuff. We are driving a one ton 4x4 CUCV as HD truck which includes trail making through the woods, it is amazing how far you can go just crashing through the woods with it. Also have CUCV Blazer made from 6 parts blazers. They have cool things like M16 gun racks, black out lights, jerry can holders, spot lights, places for electronic gear, dual battery and alternator set-ups, and almost crash- proof bumpers. Thanks for sharing your project with us. Please keep reporting. Les

Register or Log In To remove these advertisements.