Highlander interior before and after - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**jocko** · 06-09-2014, 11:09 PM

Been workin on this turd for quite a while. But it's time to move, so I needed to button it up for the trip. Still awaiting seat belt retractor parts, but that's about it. Still need to bolt in the seat also (a little off center in the pic).

The previously mentioned noticeable gap in the driver's (and passenger) side outer cushion area where the back and bottom met turned out to be nothing more than a new seat foam issue. Took it all apart and examined it compared to the original GM foam and it was just not quite right in the lower seat back areas on the outer edges. Ended up going back to my original 72 foam and it took care of the issue. No visible gaps between the back/bottom now. Glad that got resolved. Found it a bit of a challenge to get all the plaid to line up in straight lines, but I'll live with what it ended up as.

Because of the pending move, had to put off the door rehab project - so, will fill the speaker holes and paint the doors at some point in the future, just wanted to make them semi-presentable for now. Redid the dash, added a tach and vac , and finally resolved my temp gauge/sender issues. All the gauges work, which is kinda nice for a change. And added in a factory am/fm that sounds pretty darn good through a single factory speaker. Nice and tinny, just like I like it

Added an AM/FM antenna and a splitter for that inevitable CB radio install thread... I wonder if there's even anyone to talk to on that thing anymore. have a few stuffed away in boxes that have never been used, and will be nice to stick it in without an extra CB antenna. But, that's for another day.

Now if I could just get my doors to shut after the new seal install... Ha. They're coming along. Hopeful they will loosen up a bit after sitting in the sun still.

Anyway, a special thanks to Tim at Truckseats - this was no easy task to get the highlander plaid with the scrollwork, appreciate your perseverance. Also thanks to Tom for the tach/vac tin and Brian Mac for his HUGE help on the temp sender issue I had. Also Wes over at Classic Heartbeat - thanks for several small parts and the dash bezel and lens and the perfect carpet - they are top quality, very pleased. LedZepp - Scott, was a pleasure to meet you, you probably wondered what ever became of the dash pad I bought from you when I picked up the green door... And Pete, thanks so much for reproducing the Main/Aux fuel tanks selector sticker - that made my day.

**70cst** · 06-09-2014, 11:16 PM

Very nice job.

**thelonerife** · 06-10-2014, 12:30 AM

I love it!

9teen69 · 06-10-2014, 12:35 AM

Looks clean...love the plaid!

**FirstOwner69** · 06-10-2014, 12:41 AM

Beautiful!

**Ol Blue K20** · 06-10-2014, 12:49 AM

Looks great Jocko....did I miss something, where you moving to....

**jocko** · 06-10-2014, 01:02 AM

THAT'S a great question - don't know for sure yet! But my time workin for uncle sam is comin to a close. Gotta go find a job. Trying to find something near Phoenix/Mesa, but pretty wide open for now.

YBNORML · 06-10-2014, 01:10 AM

Looking great! I just can't get enough of these interiors, it really finishes the trucks off nicely.

leftybass209 · 06-10-2014, 01:18 AM

That's a good look!

**leddzepp** · 06-10-2014, 01:24 AM

Mark- It was very nice meeting you as well. That interior is awesome! The seat just steals the show. Congrats on getting to move where you want and best of luck in finding a new job.

**Ol Blue K20** · 06-10-2014, 01:54 AM

Quote:

Originally Posted by jocko

THAT'S a great question - don't know for sure yet! But my time workin for uncle sam is comin to a close. Gotta go find a job. Trying to find something near Phoenix/Mesa, but pretty wide open for now.

Well I hope this "coming to a close" means a retirement and moving on to a more relaxed employment. ...Best of luck finding what ya want where ya want.

**jocko** · 06-10-2014, 02:41 AM

ha, no, just round 1 of retiring. which really just means a career change nowadays.

Bluechevy68 · 06-10-2014, 07:31 AM

now that is show quality!

**DeadheadNM** · 06-10-2014, 08:41 AM

Awesome work Mark! Glad you put the decal to use. How did you get the door panels clean - plain old elbow grease?

Lee H · 06-10-2014, 08:58 AM

Very nice! Question for you, any special reason you went with parchment VS black belts? I wrestled with that when I redid mine.

yfs200p · 06-10-2014, 09:36 AM

That looks very nice. That scroll in the center really makes the difference. I wasn't up for jumping through the hoops to get that done on mine, and kind of wish i had. Quite the improvement!

alsriv2 · 06-10-2014, 10:21 AM

Really like the clean lines and look of that interior. Great job on bringing back to life.

KEL · 06-10-2014, 11:38 AM

It really is amazing what a seat can do !

Lanman1972 · 06-10-2014, 11:43 AM

Just installed mine this weekend, Loving me some 70's Plaid! Dog matches perfect!

**jocko** · 06-10-2014, 12:02 PM

Quote:

Originally Posted by DeadheadNM

Awesome work Mark! Glad you put the decal to use. How did you get the door panels clean - plain old elbow grease?

Nope, not much elbow grease involved in that - the originals were even worse than they appear in the picture - very stained, etc. I replaced em with a better set!

I do plan to resto the originals when I get a chance, but they may be candidates for a redye or paint.

**jocko** · 06-10-2014, 12:14 PM

Quote:

Originally Posted by Lee H

Very nice! Question for you, any special reason you went with parchment VS black belts? I wrestled with that when I redid mine.

Lee, I went with parchment because it had the original parchment belts still on it when I bought it from the original owner. I've occasionally seen parchment with black, but have always thought that parchment belts were the norm with a parchment highlander seat. Hope I didn't screw the pooch, but that is what was on it and they were very "original" (i.e. pretty trashed)

Lee H · 06-10-2014, 12:20 PM

Quote:

Originally Posted by jocko

Lee, I went with parchment because it had the original parchment belts still on it when I bought it from the original owner. I've occasionally seen parchment with black, but have always thought that parchment belts were the norm with a parchment highlander seat. Hope I didn't screw the pooch, but that is what was on it and they were very "original" (i.e. pretty trashed)

Mark, I have always heard, and research indicates parchment or black belts are factory correct with parchment interior, I don't know about highlander. I went with black belts because the column, carpet and dash pad are black. I do have a very nice set of parchment belts, I'm going to put them on for awhile now that I've seen yours. Cheers, Lee

**jocko** · 06-10-2014, 12:42 PM

I think your belts look great in black Lee - parchment buckets with black houndstooth - a great look. I had to go double check my "highlander files" - here's what I found from original sales brochures for the highlander, but who knows what happened in the factory... Ha! Yours looks great with black, and white would probably look great also, especially since you have both black and white in your houndstooth inserts.

Lee H · 06-10-2014, 12:56 PM

After seeing the sales brochures it's clear parchment is the right choice! Black would not look right. Kudos.....

**leddzepp** · 06-10-2014, 01:48 PM

Truck could have come with either black or parchment seatbelts. Both look good, but black won't get dirty

06-09-2014, 11:09 PM	#1
jocko Senior Member Join Date: Oct 2009 Location: Godley, TX Posts: 17,975	Highlander interior before and after Been workin on this turd for quite a while. But it's time to move, so I needed to button it up for the trip. Still awaiting seat belt retractor parts, but that's about it. Still need to bolt in the seat also (a little off center in the pic). The previously mentioned noticeable gap in the driver's (and passenger) side outer cushion area where the back and bottom met turned out to be nothing more than a new seat foam issue. Took it all apart and examined it compared to the original GM foam and it was just not quite right in the lower seat back areas on the outer edges. Ended up going back to my original 72 foam and it took care of the issue. No visible gaps between the back/bottom now. Glad that got resolved. Found it a bit of a challenge to get all the plaid to line up in straight lines, but I'll live with what it ended up as. Because of the pending move, had to put off the door rehab project - so, will fill the speaker holes and paint the doors at some point in the future, just wanted to make them semi-presentable for now. Redid the dash, added a tach and vac , and finally resolved my temp gauge/sender issues. All the gauges work, which is kinda nice for a change. And added in a factory am/fm that sounds pretty darn good through a single factory speaker. Nice and tinny, just like I like it Added an AM/FM antenna and a splitter for that inevitable CB radio install thread... I wonder if there's even anyone to talk to on that thing anymore. have a few stuffed away in boxes that have never been used, and will be nice to stick it in without an extra CB antenna. But, that's for another day. Now if I could just get my doors to shut after the new seal install... Ha. They're coming along. Hopeful they will loosen up a bit after sitting in the sun still. Anyway, a special thanks to Tim at Truckseats - this was no easy task to get the highlander plaid with the scrollwork, appreciate your perseverance. Also thanks to Tom for the tach/vac tin and Brian Mac for his HUGE help on the temp sender issue I had. Also Wes over at Classic Heartbeat - thanks for several small parts and the dash bezel and lens and the perfect carpet - they are top quality, very pleased. LedZepp - Scott, was a pleasure to meet you, you probably wondered what ever became of the dash pad I bought from you when I picked up the green door... And Pete, thanks so much for reproducing the Main/Aux fuel tanks selector sticker - that made my day. Attached Images

06-09-2014, 11:16 PM	#2
70cst Senior Member Join Date: Feb 2001 Location: New Madison, Ohio Posts: 21,373	Re: Highlander interior before and after Very nice job. __________________ A husband can be right...or...A husband can be happy. 67-72 Chevy and GMC Trucks...The Classic Truck for the Classic Folk. 1970 CST Two tone green, 402BB, 400 Automatic, Tach, Buckets, AC, AM-FM, Tilt, GM CB, GM 8 Tract, LWB, etc JOHN 17:3...The better side of "LIFE" Remember: Everyday is a good day...Some are just gooder!

06-10-2014, 12:30 AM	#3
thelonerife Senior Member Join Date: Jul 2007 Location: Clarksville TN 37043 Posts: 8,702	Re: Highlander interior before and after I love it! __________________ Chuck 68swb Fleetside build ''Choncho'' http://67-72chevytrucks.com/vboard/s...d.php?t=374892 My trailer redo http://67-72chevytrucks.com/vboard/s...69#post5893869 Chuy my 59 bug http://67-72chevytrucks.com/vboard/s...d.php?t=653798 Putnam 87 GMC Shop truck http://67-72chevytrucks.com/vboard/s...d.php?t=707687

06-10-2014, 12:35 AM	#4
9teen69 Registered User Join Date: Sep 2002 Location: Austin, Texas Posts: 1,048	Re: Highlander interior before and after Looks clean...love the plaid! __________________ 72 Cheyenne SWB C10 (daily driver) (Super fake cause I just love the glovebox emblem) 70 Camaro RS (frame-off in pieces) 70 Camaro RS (daily driver backup) 69 Custom LWB C10 (son now drives)

06-10-2014, 12:41 AM	#5
FirstOwner69 Senior Member Join Date: May 2010 Location: Wisconsin & Arizona Posts: 4,852	Re: Highlander interior before and after Beautiful!

06-10-2014, 12:49 AM	#6
Ol Blue K20 Proprietor of Dale's Corner Join Date: Nov 2012 Location: Vacaville , CA Posts: 16,245	Re: Highlander interior before and after Looks great Jocko....did I miss something, where you moving to.... __________________ "Some Days Chickens And Some Days Feathers" Dale XNGH ECV Sam Brannan 1004 R.I.P. 67ChevyRedneck R.I.P. Grumpy Old Man R.I.P. FleetsidePaul

06-10-2014, 01:02 AM	#7
jocko Senior Member Join Date: Oct 2009 Location: Godley, TX Posts: 17,975	Re: Highlander interior before and after THAT'S a great question - don't know for sure yet! But my time workin for uncle sam is comin to a close. Gotta go find a job. Trying to find something near Phoenix/Mesa, but pretty wide open for now.

06-10-2014, 01:10 AM	#8
YBNORML Registered User Join Date: May 2010 Location: Edmonton, Alberta Posts: 3,844	Re: Highlander interior before and after Looking great! I just can't get enough of these interiors, it really finishes the trucks off nicely.

06-10-2014, 01:18 AM	#9
leftybass209 Registered User Join Date: Feb 2011 Location: Modesto, CA Posts: 2,189	Re: Highlander interior before and after That's a good look!

06-10-2014, 01:24 AM	#10
leddzepp Moderator Join Date: May 2007 Location: Southern Cal Posts: 20,031	Re: Highlander interior before and after Mark- It was very nice meeting you as well. That interior is awesome! The seat just steals the show. Congrats on getting to move where you want and best of luck in finding a new job. __________________ 1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed. 1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck. RIP ElJay RIP 67ChevyRedneck RIP Grumpy Old Man RIP FleetsidePaul

06-10-2014, 02:41 AM	#12
jocko Senior Member Join Date: Oct 2009 Location: Godley, TX Posts: 17,975	Re: Highlander interior before and after ha, no, just round 1 of retiring. which really just means a career change nowadays.

06-10-2014, 07:31 AM	#13
Bluechevy68 Registered User Join Date: Nov 2011 Location: London,KY Posts: 299	Re: Highlander interior before and after now that is show quality!

06-10-2014, 08:41 AM	#14
DeadheadNM Carpe manana Join Date: Dec 2010 Location: Eau Claire, WI Posts: 12,443	Re: Highlander interior before and after Awesome work Mark! Glad you put the decal to use. How did you get the door panels clean - plain old elbow grease? __________________ 1972 K5 CST Highlander Blazer: http://67-72chevytrucks.com/vboard/s...d.php?t=708547 1972 K20 Cheyenne Super: http://67-72chevytrucks.com/vboard/s...d.php?t=528308 Members met: ORANGBLAZ, 2003 silverado, MikeCofield, BB72CHEVKT, Duncan&Son, Sameyrasmea72, THENEWMEXICAN, HotRod C/10, brianthelion02, Sport/Truck, ryanroo, michael bustamante, Dirt's72, Already Gone, WestButteTruck, 57taskforce, Moreyel, painterljp, AASmedic, SoCoC10, Lumaestas, carbuff382, Chevyland

06-10-2014, 08:58 AM	#15
Lee H Registered User Join Date: Jun 2010 Location: Upland Ca Posts: 4,147	Re: Highlander interior before and after Very nice! Question for you, any special reason you went with parchment VS black belts? I wrestled with that when I redid mine. __________________ 1972 C10 SWB, Air, PS, PB, 350/350THM. Second owner. 1965 Corvette roadster, 44K miles, 327/365 SHP, 4 speed, side exhaust, knockoffs, teak, second owner (bought in 1970), Have ALL numbers matching components. My frame off restoration thread: http://67-72chevytrucks.com/vboard/s...d.php?t=556703

06-10-2014, 09:36 AM	#16
yfs200p E.H.F.D Engine #2 Join Date: Feb 2003 Location: East Hampton, NY Long Island Posts: 916	Re: Highlander interior before and after That looks very nice. That scroll in the center really makes the difference. I wasn't up for jumping through the hoops to get that done on mine, and kind of wish i had. Quite the improvement! __________________ -NICK '72 K10 SWB Fleetside. Avocado Highlander 350-4speed-NP205 Frame Off Re-Creation '89 GMC V3500 C/C Flatbed Plow Truck 454/SM465/Np205 '15 Chevy 2500HD CCSB High Country Duramax '22 Tahoe Premier Duramax



Register or Log In To remove these advertisements.

06-10-2014, 10:21 AM	#17
alsriv2 Registered User Join Date: Sep 2010 Location: Formerly MD and San Diego, now loving life in Arizona Posts: 1,636	Re: Highlander interior before and after Really like the clean lines and look of that interior. Great job on bringing back to life. __________________ Alan 2012 Ram 3500 Dually Crew Cab 6.7 Cummins 2014 Palomino Columbus 340RK 5th wheel '69 Chevy C10 396BB

06-10-2014, 11:38 AM	#18
KEL 72 GMC Join Date: Feb 2008 Location: Wells, Maine Posts: 534	Re: Highlander interior before and after It really is amazing what a seat can do ! __________________ KEL Members I have met : 2014.02.01: bruceman1968, Mr Handy, colgad, RenoKeene, CaptRMW

06-10-2014, 11:43 AM	#19
Lanman1972 Registered User Join Date: Dec 2013 Location: Omaha NE Posts: 620	Re: Highlander interior before and after Just installed mine this weekend, Loving me some 70's Plaid! Dog matches perfect! Attached Images

06-10-2014, 12:42 PM	#23
jocko Senior Member Join Date: Oct 2009 Location: Godley, TX Posts: 17,975	Re: Highlander interior before and after I think your belts look great in black Lee - parchment buckets with black houndstooth - a great look. I had to go double check my "highlander files" - here's what I found from original sales brochures for the highlander, but who knows what happened in the factory... Ha! Yours looks great with black, and white would probably look great also, especially since you have both black and white in your houndstooth inserts. Attached Images

06-10-2014, 12:56 PM	#24
Lee H Registered User Join Date: Jun 2010 Location: Upland Ca Posts: 4,147	Re: Highlander interior before and after After seeing the sales brochures it's clear parchment is the right choice! Black would not look right. Kudos..... __________________ 1972 C10 SWB, Air, PS, PB, 350/350THM. Second owner. 1965 Corvette roadster, 44K miles, 327/365 SHP, 4 speed, side exhaust, knockoffs, teak, second owner (bought in 1970), Have ALL numbers matching components. My frame off restoration thread: http://67-72chevytrucks.com/vboard/s...d.php?t=556703

06-10-2014, 01:48 PM	#25
leddzepp Moderator Join Date: May 2007 Location: Southern Cal Posts: 20,031	Re: Highlander interior before and after Truck could have come with either black or parchment seatbelts. Both look good, but black won't get dirty __________________ 1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed. 1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck. RIP ElJay RIP 67ChevyRedneck RIP Grumpy Old Man RIP FleetsidePaul

Register or Log In To remove these advertisements.