![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
![]() Join Date: Dec 2012
Location: Chandler AZ
Posts: 1,149
|
What to be done for stripped/frozen door panel screws?
I am in the process of replacing the door panels for my little truck. 2 of the pressed in nuts for the door panel screws, which are technically bolts, have dropped out of the door.
Are there cage nuts that I could put in? I don't weld, (it is on my bucket list) so I can't put square nuts behind and tack in place. What would be an easy effective, way to proceed please?
__________________
1970 Longhorn, Front Disc, 350/4 bolt, 882 heads, HEI, Edelbrock, 700R4, HO-52/4.11. 1996 Corvette, Collector Roadster, LT4, 396, 450RWHP, 6sp, 4.11/Dana44/posi 5 point roll bar And let us not grow weary of doing good, for in due season we will reap, if we do not give up. Gal 6:9 |
![]() |
![]() |
![]() |
#2 |
I am a Referee of life.
Join Date: Jun 2000
Location: Greensboro N.C.
Posts: 13,993
|
Re: What to be done for stripped/frozen door panel screws?
IIRC I used cage nuts. It's been a while since I had the panels off but I haven't had any problem. I think I used ones that clip over the edge and reach the hole.Hope this helps. They may be J nuts.
__________________
The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil" |
![]() |
![]() |
![]() |
#3 |
member #16
![]() Join Date: Dec 1999
Location: Yuba City Ca.
Posts: 3,618
|
Re: What to be done for stripped/frozen door panel screws?
Wes at classicheartbeat has the caged nuts.
http://www.classicheartbeat.com/nuts_&_bolts1.htm
__________________
john http://67-72chevytrucks.com/vboard/showgroups.php board vendors ![]() http://www.flickr.com/photos/1745471...7602865984234/ |
![]() |
![]() |
![]() |
#4 |
Registered User
![]() Join Date: Dec 2012
Location: Chandler AZ
Posts: 1,149
|
Re: What to be done for stripped/frozen door panel screws?
thanks guys. I figured it would be something like that. I do have the screws already. I'll bring them to the Ace store and get the capture nuts.
__________________
1970 Longhorn, Front Disc, 350/4 bolt, 882 heads, HEI, Edelbrock, 700R4, HO-52/4.11. 1996 Corvette, Collector Roadster, LT4, 396, 450RWHP, 6sp, 4.11/Dana44/posi 5 point roll bar And let us not grow weary of doing good, for in due season we will reap, if we do not give up. Gal 6:9 |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Oct 2008
Location: Marianna Arkansas
Posts: 7,269
|
Re: What to be done for stripped/frozen door panel screws?
Plastic license plate clips the kind that snap into the bumper, will do well in a pinch for those metal little suckers. That would be the 99 cent solution, but they are probably a couple bucks now. I don't look to often at prices of stuff by the time I need it I need it.
|
![]() |
![]() |
![]() |
#6 | |
The Older Generation
![]() ![]() ![]() Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,487
|
Re: What to be done for stripped/frozen door panel screws?
Quote:
This is what I used for mine.... LockDoc
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - |
|
![]() |
![]() |
![]() |
Bookmarks |
|
|