Kooks 1 7/8 headers+ stage2 dropmember= WINNING - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Last_Paladin · 04-19-2012, 09:57 AM

Is there any chance you could measure from the center of the bolt on the Xmember gusset to the engine block on the DM engine mount? I got mine in today and they do not fit. Looks like I need to go up with the engine.

c10seconds · 04-25-2012, 12:54 AM

Quote:

Originally Posted by Last_Paladin

Is there any chance you could measure from the center of the bolt on the Xmember gusset to the engine block on the DM engine mount? I got mine in today and they do not fit. Looks like I need to go up with the engine.

Could you post a pic of what you are having issues with? Also my dropmember is the one that does not require the c-notches for the rack so it may be a little different including the motor mounts

Last_Paladin · 04-25-2012, 08:50 AM

Quote:

Originally Posted by c10seconds

Could you post a pic of what you are having issues with? Also my dropmember is the one that does not require the c-notches for the rack so it may be a little different including the motor mounts

I ordered some from Nathan. You're right, in that we're on different Dropmembers.

Last_Paladin · 05-19-2012, 11:01 AM

Mine are scant MM away from the frame rails.

paul66c10 · 07-19-2012, 08:51 AM

Did you ever get the steering linkage routed? wondering how this turned out im in the process of looking for headers for my 86 with a extreme dropmember and thinking these may work just wondering about the steering linkage.

c10seconds · 07-22-2012, 06:26 PM

Quote:

Originally Posted by paul66c10

Did you ever get the steering linkage routed? wondering how this turned out im in the process of looking for headers for my 86 with a extreme dropmember and thinking these may work just wondering about the steering linkage.

I havent got that figured out yet as I havent had much time to work on the truck. Its gonna be a tight fit but it will work out.

Revolution · 11-21-2012, 08:00 PM

Any more updates on these? I was wondering if I could see a shot from below. I am a kooks dealer and we are doing a 67 c10 for a customer he would be thrilled as would I if these work out for his 408

c10seconds · 11-30-2012, 04:43 AM

Quote:

Originally Posted by Revolution

Any more updates on these? I was wondering if I could see a shot from below. I am a kooks dealer and we are doing a 67 c10 for a customer he would be thrilled as would I if these work out for his 408

Sorry for the delay...
Here are a couple extra pics so you can get a better look at clearance. The collectors sit much higher with the trans xmember mounted

**Hart_Rod** · 11-30-2012, 03:29 PM

Quote:

Originally Posted by c10seconds

It is the mild dropmember and as far as I know, it leaves the motor in stock location.

For the guys with the extreme dropmember the DT 's didn't work because of the motor being raised. There are clearance issues at the firewall. They probably would have worked for me but I just decided on the kooks. The driver side collector is slightly lower than the passenger but I don't think it will be an issue.

I haven't checked to see if the stock inner fender will work. Would be great if they did but Ill have to check with Nate
Posted via Mobile Device

Which Doug Thorleys wouldn't work with the extreme DM, the small tubes or the big tubes?
Posted via Mobile Device

c10seconds · 11-30-2012, 03:39 PM

Quote:

Originally Posted by Hart_Rod

Which Doug Thorleys wouldn't work with the extreme DM, the small tubes or the big tubes?
Posted via Mobile Device

The big tube DT headers hit the firewall. You ready to buy some big brakes?

Posted via Mobile Device

**Hart_Rod** · 11-30-2012, 03:49 PM

Quote:

Originally Posted by c10seconds

The big tube DT headers hit the firewall. You ready to buy some big brakes?

Posted via Mobile Device

So the small tubes work OK? Man, I would love to have the brakes, BUT, I have 18s on the front of my truck, and I'm not putting $5k worth of brakes on my sons truck...

.
Posted via Mobile Device

Revolution · 11-30-2012, 05:23 PM

Thanks so much for the pictures. I am going to order a set from Kooks tomorrow for our customer they look great. If anyone on the thread needs or wants a set let me know I will gladly hook it up for anyone on the forum I am loving this build I have only done later silverados till now but I am loving this build.

smartass12 · 12-01-2012, 08:42 AM

I didnt see a clear answer (i am blind though) so do these kooks work with the extreme dropmembers??

c10seconds · 12-02-2012, 10:30 PM

Quote:

Originally Posted by Last_Paladin

Is there any chance you could measure from the center of the bolt on the Xmember gusset to the engine block on the DM engine mount? I got mine in today and they do not fit. Looks like I need to go up with the engine.

From this post I would say the kooks wont work with the extreme dropmember. But you could try sending last_paladin a message for more info.

c10seconds · 12-02-2012, 10:32 PM

Quote:

Originally Posted by Hart_Rod

So the small tubes work OK? Man, I would love to have the brakes, BUT, I have 18s on the front of my truck, and I'm not putting $5k worth of brakes on my sons truck...

.
Posted via Mobile Device

Im not sure about the small tube DT headers. If the big ones didnt fit then i dont see why the small ones would but you never know.

BigShoe24 · 12-02-2012, 10:39 PM

c10seconds, sweet ride dude. What wiring harness are you using?

Last_Paladin · 12-02-2012, 11:21 PM

Quote:

Originally Posted by c10seconds

Im not sure about the small tube DT headers. If the big ones fit then i dont see why the small ones wouldnt but you never know.

They didn't fit. I have the extreme. I ended up making some for my LS3 based motor. I also have custom engine stands from Nate, so I am a little taller.

c10seconds · 12-03-2012, 04:55 AM

Quote:

Originally Posted by BigShoe24

c10seconds, sweet ride dude. What wiring harness are you using?

Thanks! I got the harness from SSP wiring. Seems to be a good product with everything nicely wrapped and them being only about a 1.5 hour drive was a plus. There wont be very many wires exposed when its all tucked away. Especially with this little TVS on top

smartass12 · 12-03-2012, 09:57 AM

So it seems the pasesetters are the way to go for extreme?

**Hart_Rod** · 12-03-2012, 10:07 AM

Quote:

Originally Posted by c10seconds

Thanks! I got the harness from SSP wiring. Seems to be a good product with everything nicely wrapped and them being only about a 1.5 hour drive was a plus. There wont be very many wires exposed when its all tucked away. Especially with this little TVS on top

The "huffer" looks good! What do you have underneath it? (specs please,

) Also, what angle did you set your motor at?

slowcpe · 01-13-2015, 11:03 AM

Going to bring this back from the dead. I know I sent you a PM but also wanted to see if anyone else had success with the steering linkage and these headers. Or any other long tube for that matter.

Hillbilly Deluxe 65 · 02-27-2015, 06:17 PM

Quote:

Originally Posted by smartass12

So it seems the pasesetters are the way to go for extreme?

what part number pacesetters worked?
why dont the kooks work on the extreme dropmember?

Parishchief1 · 06-20-2016, 10:48 PM

I'm running a 67 with a mild pb dropmember and I'm looking to run these long tube headers has anyone got the steering linkage working??

04-19-2012, 09:57 AM	#26
Last_Paladin Registered User Join Date: Feb 2011 Location: Beverly, MA Posts: 472	Re: Kooks 1 7/8 headers+ stage2 dropmember= WINNING Is there any chance you could measure from the center of the bolt on the Xmember gusset to the engine block on the DM engine mount? I got mine in today and they do not fit. Looks like I need to go up with the engine.

05-19-2012, 11:01 AM	#29
Last_Paladin Registered User Join Date: Feb 2011 Location: Beverly, MA Posts: 472	Re: Kooks 1 7/8 headers+ stage2 dropmember= WINNING Mine are scant MM away from the frame rails.

07-19-2012, 08:51 AM	#30
paul66c10 Registered User Join Date: Oct 2005 Location: chesapeake, va Posts: 89	Re: Kooks 1 7/8 headers+ stage2 dropmember= WINNING Did you ever get the steering linkage routed? wondering how this turned out im in the process of looking for headers for my 86 with a extreme dropmember and thinking these may work just wondering about the steering linkage. __________________ 1986 gmc shortbed (right now its rough) porterbuilt dropmember front mmw flat plate uppers and lowers, soon to have porterbuilt rear dropmember, painted cherry red rallies, flat green primer in the works with a gloss white roof, 92 civic dx daily beater, 01 z06 new toy

11-21-2012, 08:00 PM	#32
Revolution Registered User Join Date: Oct 2010 Location: Nevada Posts: 3	Re: Kooks 1 7/8 headers+ stage2 dropmember= WINNING Any more updates on these? I was wondering if I could see a shot from below. I am a kooks dealer and we are doing a 67 c10 for a customer he would be thrilled as would I if these work out for his 408

11-30-2012, 05:23 PM	#37
Revolution Registered User Join Date: Oct 2010 Location: Nevada Posts: 3	Re: Kooks 1 7/8 headers+ stage2 dropmember= WINNING Thanks so much for the pictures. I am going to order a set from Kooks tomorrow for our customer they look great. If anyone on the thread needs or wants a set let me know I will gladly hook it up for anyone on the forum I am loving this build I have only done later silverados till now but I am loving this build.

12-01-2012, 08:42 AM	#38
smartass12 Registered User Join Date: Jan 2012 Location: orange county, california Posts: 363	Re: Kooks 1 7/8 headers+ stage2 dropmember= WINNING I didnt see a clear answer (i am blind though) so do these kooks work with the extreme dropmembers?? __________________ My 67 stepside build http://67-72chevytrucks.com/vboard/s...d.php?t=522760

12-02-2012, 10:39 PM	#41
BigShoe24 True Addiction Join Date: Nov 2005 Location: FTL Posts: 415	Re: Kooks 1 7/8 headers+ stage2 dropmember= WINNING c10seconds, sweet ride dude. What wiring harness are you using? __________________ RCC

12-03-2012, 09:57 AM	#44
smartass12 Registered User Join Date: Jan 2012 Location: orange county, california Posts: 363	Re: Kooks 1 7/8 headers+ stage2 dropmember= WINNING So it seems the pasesetters are the way to go for extreme? __________________ My 67 stepside build http://67-72chevytrucks.com/vboard/s...d.php?t=522760

01-13-2015, 11:03 AM	#46
slowcpe Registered User Join Date: Sep 2013 Location: Evansville, IN Posts: 1,774	Re: Kooks 1 7/8 headers+ stage2 dropmember= WINNING Going to bring this back from the dead. I know I sent you a PM but also wanted to see if anyone else had success with the steering linkage and these headers. Or any other long tube for that matter. __________________ Ryan 1967 Red Stepside..."Laymond" http://67-72chevytrucks.com/vboard/s...40#post6441840 1972 Medium Olive SWB-Chester http://67-72chevytrucks.com/vboard/s...d.php?t=759628 1967/71 Blue SWB C10..SOLD 1977 SWB K10..my grandpa's.....never should have sold

06-20-2016, 10:48 PM	#48
Parishchief1 Registered User Join Date: Mar 2014 Location: New orleans Posts: 28	Re: Kooks 1 7/8 headers+ stage2 dropmember= WINNING I'm running a 67 with a mild pb dropmember and I'm looking to run these long tube headers has anyone got the steering linkage working?? __________________ 67' C-10 PBFAB suspension,Accuair, Baer Pro+ 14" big brake kit F&R, Narrowed moser 12 bolt,Boyd Slayer 24x9's & 24x15's. 405 GANG500HP Ls "Da Green Beast"



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.