WA Dash - Uncut, A/C and non $125 plus shipping

[randy500]

I just checked shipping for a member here to TX at $54 residential and $50 commercial. I have several of each. Will post pictures later.

[Mryan]

Interested in Non A/C

[randy500]

Originally Posted by Mryan

Interested in Non A/C

I have this one with 4 small holes in the radio area and another green one with dual tank switch hole to left of instrument cluster. This one is still in the vehicle and I could cut it out how you want. the other is cut out at the windshield pinch weld with 1/2 inch or so of the outside of the cab attached to the pinch weld.

[Mryan]

Damn, I hate to say this but just researched what it takes to remove a dash. I'm not sure that I am up for that kind of project yet. I will let you know. Thanks

[randy500]

Just so you know there are a couple ways of changing the dash panel.

1. You can cut the center dash out under the gauge panel and under the glove box door and at the top behind the dash pad. With this method you can leave in all the wiring and just remove the gauges dash pad and glove box door.

2. The left and right of the dash is bolted at the sides to the cab, you can remove the bolts and then cut it out behind the dash pad and tack it back in. This I think is the easiest except you probably will remove the steering column and wiring harness.

3. The most comprehensive way is to cut it out at the windshield pinch weld. This can be preferred if you have rust at the front of the dash and or pinch weld that needs to be repaired.

So there you have it!

[randy500]

I still have some of these...

[Last_Paladin]

Still have them for sale?

[randy500]

Originally Posted by Last_Paladin

Still have them for sale?

I do, what's ur zip and I will get you shipping cost

[randy500]

Pictures of currently on hand dashes. 2 dark olive non-a/c and med olive and blue a/c dashes, the blue one has aux fuel tank switch hole to left of instrument cluster

[desertnick69]

Randy500 not interested in the dash but I need the upper chrome on the pass side below the dash's. Is that for sale?

[randy500]

Originally Posted by desertnick69

Randy500 not interested in the dash but I need the upper chrome on the pass side below the dash's. Is that for sale?

Fender trim? I could sell you that. Problem is shipping cost, it's probably over $20 to ship and would need $20 for the piece since it takes so much time to remove make a box and ship it

[richard2717]

Randy
I would be interested in the med. olive ashtray & bracket if the paint is in good shape. Shipping to 21801

Richard

[randy500]

Originally Posted by richard2717

Randy
I would be interested in the med. olive ashtray & bracket if the paint is in good shape. Shipping to 21801

Richard

You can have it for the cost of shipping, here is a pic.

[randy500]

Richard, have you found that soft ray window I need?

[richard2717]

Originally Posted by randy500

Richard, have you found that soft ray window I need?

Randy
I have a few feelers out but nothing concrete on the window yet. Let me know what the shipping will be and I will get some paypal over to you for the ashtray. It looks fine for what I need. I am also looking for a med. olive cowl panel.
Richard

[randy500]

Shipping is small flat rate usps, about $6.50 or so. I Think I have a cowl panel. My PayPal is randy501@outlook.com

[randy500]

Very patina and repainted

[richard2717]

It is about what i am looking for. what you figure $$$$ to get it here? I don't think the ashtray will fit in a small flat rate either with the bracket. If the cowl is not too bad shipping and all we can just combine. I will pm my address

[randy500]

Ashtray fits ok

[desertnick69]

Originally Posted by desertnick69

Randy500 not interested in the dash but I need the upper chrome on the pass side below the dash's. Is that for sale?

Could I get a better pic of the chrome strip on that fender?

[randy500]

Originally Posted by desertnick69

Could I get a better pic of the chrome strip on that fender?

The one on the green fender is nicer, blue one has a push dent near the tip

[randy500]

I have these ones too...far right is pretty shiny still

[desertnick69]

Originally Posted by randy500

Fender trim? I could sell you that. Problem is shipping cost, it's probably over $20 to ship and would need $20 for the piece since it takes so much time to remove make a box and ship it

Randy500 Does that include "hardware"? Find the best looking one and let me know how muck to 85027. As far as the shipping just get a piece of pvc. pipe that the strip will fit in pad it at the ends cap it & ship!!

[randy500]

Originally Posted by desertnick69

Randy500 Does that include "hardware"? Find the best looking one and let me know how muck to 85027. As far as the shipping just get a piece of pvc. pipe that the strip will fit in pad it at the ends cap it & ship!!

It has all the clips and nuts. I will ship it in triangular folded cardboard with 1 x3 wood reinforcement, I have done it before that way. Send $40 to PayPal with description of part your buying. randy501@outlook.com is my PayPal or click on PayPal link below. Make sure you have an address in there, I will ship tomorrow

[richard2717]

PP sent for ash tray & Cowl

thanks
Richard