I'm out of whack somewhere... but where? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**KyleSeal** · 01-04-2017, 07:32 PM

New body mounts (energy suspension poly's) and I kept the original shims in place with new washers, but the cab seems to be high on the driver side, and the control arms seem to sit at different angles.... any way to adjust?

**KyleSeal** · 01-04-2017, 07:33 PM

First photo is passenger side arm and second is driver

**KyleSeal** · 01-04-2017, 07:35 PM

These arms seem to be at different angles...

**LockDoc** · 01-04-2017, 07:51 PM

-
Sounds like one of your front coil springs may be weak and sagging....

LockDoc

**KyleSeal** · 01-04-2017, 08:01 PM

Quote:

Originally Posted by LockDoc

-
Sounds like one of your front coil springs may be weak and sagging....

LockDoc

Which is strange cause they're brand new, with barley 100 miles on them.

demian5 · 01-04-2017, 08:10 PM

Looks like you need to do more research and measuring to see if and what is bent or installed incorrectly.

**LockDoc** · 01-04-2017, 08:17 PM

Quote:

Originally Posted by KyleSeal

Which is strange cause they're brand new, with barley 100 miles on them.

If you have a flat concrete floor measure both frame rails in the front, center, and rear of the truck and see what you come up with....

LockDoc

**KyleSeal** · 01-04-2017, 08:46 PM

I did notice however that my springs (when truck is jacked and no weight on suspension) my drivers spring I can move with my hand and passenger is movable but much tougher to move/wiggle. They're 3 inch CPP drop springs.

weq92f · 01-04-2017, 08:54 PM

Make sure the springs are seated properly into the notch in the lower control arm?

On a 68 1/2 ton, leaving one out of the notch caused that side to ride higher by about an inch.

-klb

01-04-2017, 07:32 PM	#1
KyleSeal Senior Member Join Date: Mar 2014 Location: Toano, VA Posts: 884	I'm out of whack somewhere... but where? New body mounts (energy suspension poly's) and I kept the original shims in place with new washers, but the cab seems to be high on the driver side, and the control arms seem to sit at different angles.... any way to adjust? Attached Images __________________ "Sometimes I do serve as a good bad example. Glad to be of service." My Build Thread (1967 C10, lowered, EFI, daily truck): http://67-72chevytrucks.com/vboard/s...d.php?t=830809

01-04-2017, 07:33 PM	#2
KyleSeal Senior Member Join Date: Mar 2014 Location: Toano, VA Posts: 884	Re: I'm out of whack somewhere... but where? First photo is passenger side arm and second is driver Attached Images __________________ "Sometimes I do serve as a good bad example. Glad to be of service." My Build Thread (1967 C10, lowered, EFI, daily truck): http://67-72chevytrucks.com/vboard/s...d.php?t=830809

01-04-2017, 07:35 PM	#3
KyleSeal Senior Member Join Date: Mar 2014 Location: Toano, VA Posts: 884	Re: I'm out of whack somewhere... but where? These arms seem to be at different angles... Attached Images __________________ "Sometimes I do serve as a good bad example. Glad to be of service." My Build Thread (1967 C10, lowered, EFI, daily truck): http://67-72chevytrucks.com/vboard/s...d.php?t=830809

01-04-2017, 07:51 PM	#4
LockDoc The Older Generation Join Date: Aug 2006 Location: Montezuma, Iowa Posts: 25,661	Re: I'm out of whack somewhere... but where? - Sounds like one of your front coil springs may be weak and sagging.... LockDoc __________________ Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 -

01-04-2017, 08:10 PM	#6
demian5 Registered User Join Date: Aug 2016 Location: Lake Forest, CA Posts: 2,177	Re: I'm out of whack somewhere... but where? Looks like you need to do more research and measuring to see if and what is bent or installed incorrectly. __________________ "Work hard, use your vacation days." 1970 C15 GMC Long Bed 1986 C20 Scottsdale 1983 K2500 Sierra Classic Suburban 6.2 Instagram: C10sofOC

01-04-2017, 08:46 PM	#8
KyleSeal Senior Member Join Date: Mar 2014 Location: Toano, VA Posts: 884	Re: I'm out of whack somewhere... but where? I did notice however that my springs (when truck is jacked and no weight on suspension) my drivers spring I can move with my hand and passenger is movable but much tougher to move/wiggle. They're 3 inch CPP drop springs. __________________ "Sometimes I do serve as a good bad example. Glad to be of service." My Build Thread (1967 C10, lowered, EFI, daily truck): http://67-72chevytrucks.com/vboard/s...d.php?t=830809

01-04-2017, 08:54 PM	#9
weq92f Registered User Join Date: Oct 2016 Location: Dallas Texas Posts: 3,164	Re: I'm out of whack somewhere... but where? Make sure the springs are seated properly into the notch in the lower control arm? On a 68 1/2 ton, leaving one out of the notch caused that side to ride higher by about an inch. -klb __________________ 67 C10 fleet fuel injected '70 402, 700r4, 3.73 posi 07 335 sport turbo 6sp 94 Trans Am GT LT1 6sp posi -- sold after 22yrs 99 540 sport V8 6sp -- sold 73 240z L24 4sp -- given to friend 68 C10 step 350/350 3.73 open -- sold



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.