|
05-12-2004, 01:39 PM
|
#1 |
|
Registered User
Join Date: Jan 2002
Location: willis tx
Posts: 374
|
header ?
what headers do i need to use to get rid of the pipes hanging below cab there were some full lenght ones for some other car that fit and I can't remember?
|
|
|
|
05-12-2004, 02:54 PM
|
#2 |
|
Registered User
Join Date: Sep 2003
Location: Boise ID
Posts: 609
|
Small block or Big block???
__________________
"72" Red CORVETTE 4-speed 350 "70" Chevy Short Bed early stages of resto. Edel 600 cfm carb Weiand Stealth Intake HEI shorty Headers 4/2 Drop 295 50R 15 TOYO on 10 inch wide corvette rally rims at all 4 corners. "CHEVY RULES" 
|
|
|
|
|
05-12-2004, 05:06 PM
|
#3 |
|
Registered User
Join Date: Jan 2002
Location: willis tx
Posts: 374
|
sorry small block
|
|
|
|
|
05-12-2004, 05:11 PM
|
#4 |
|
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
My hookers hang, but the front cross member would smack before the headers would. I have damage there to prove it too.
|
|
|
|
|
05-12-2004, 07:25 PM
|
#5 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,403
|
2nd the Hookers, i have Hooker comps on the longhorn. with a 3/5 drop, those collectors dont have any "road rash". the collectors hang about 2 - 2 1/4" below the rails (at the flange).....& like Andy said, the front susp pcs would drag 1st
 crazyL
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
|
|
|
|
05-13-2004, 03:17 PM
|
#6 |
|
Registered User
Join Date: Mar 2000
Location: Olalla, WA
Posts: 705
|
I couldn't agree more about the Hookers fit. I have Hooker Super Comps in my stepside (2wd) and Compititions in my Blazer (4wd). Here are a few pics for you to look at for fitment. To tell you I have never had a header fit so nice until I put the hookers Super Comps in my stepside. (Sorry, just an excuse to show the engine)
__________________
This is only my opinion and it is subject to change. 70 GMC Short box stepside Blown 388 Stroker 72 K/5 Blazer 350/SM465/205 Last edited by chaptr2; 05-13-2004 at 03:20 PM. |
|
|
|
|
05-14-2004, 10:40 AM
|
#7 |
|
The oddest Todd around
Join Date: May 2004
Location: Miami, Florida
Posts: 1,418
|
good to see I can fit a supercharger under the hood.
is that a 3 inch cowl induction hood? |
|
|
|
|
05-14-2004, 11:48 AM
|
#8 |
|
Registered User
Join Date: Mar 2000
Location: Olalla, WA
Posts: 705
|
That is a 3 inch cowl hood, using a 5 inch air cleaner and a drop base air cleaner bottom.
__________________
This is only my opinion and it is subject to change. 70 GMC Short box stepside Blown 388 Stroker 72 K/5 Blazer 350/SM465/205 |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
