The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1947 - 1959 Chevrolet & GMC Pickups Message Board > Projects and Builds

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 07-13-2019, 12:00 AM   #1
Jason 56
Registered User
 
Join Date: Nov 2018
Location: Ishpeming, mi
Posts: 625
Re: My 56 build

Got a start on the rocker panel. I added a piece of angle to it so I could line it up with the quarter panel. As you can see in the last picture I warped the crap out of it. Figured with the angle I could be a little more aggressive... wrong! I put some relief cuts in the top and managed to straighten it out. Just have to do the other side. Had to change direction because some of the bare metal was starting to rust in the humidity. So I spent 8 hours today getting as much prepped for paint. Looks good in primer. Also started getting parts in for my door latches. I’m going to use corvette C6 door hardware... we’ll see how that goes.
Attached Images
     
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=780018 Jason’s 56 build
Jason 56 is offline   Reply With Quote
Old 08-01-2019, 10:42 PM   #2
Jason 56
Registered User
 
Join Date: Nov 2018
Location: Ishpeming, mi
Posts: 625
Re: My 56 build

Managed to finish the rockers last week. They turned out pretty well!
Attached Images
    
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=780018 Jason’s 56 build
Jason 56 is offline   Reply With Quote
Old 08-01-2019, 10:56 PM   #3
Jason 56
Registered User
 
Join Date: Nov 2018
Location: Ishpeming, mi
Posts: 625
Re: My 56 build

Now on the the door entry system. This is where some of the custom metal work begins. Got the latch mounted and a good start on the pocket to hold the release button. Now I have to notch the b-post to match the pocket so the door seal has a place to mount. Then the notch behind the door for your hand to fit into. That’s what I have drawn out in the last picture. So far so good!
Attached Images
    
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=780018 Jason’s 56 build
Jason 56 is offline   Reply With Quote
Old 08-02-2019, 07:34 AM   #4
Mains52
Registered User
 
Join Date: Jun 2016
Location: Knoxville, Illinois
Posts: 335
Re: My 56 build

Your metal work has been great!! do you have your own metal break? Ive been thinking about buying a small one.
Mains52 is offline   Reply With Quote
Old 08-02-2019, 11:33 PM   #5
Jason 56
Registered User
 
Join Date: Nov 2018
Location: Ishpeming, mi
Posts: 625
Re: My 56 build

Quote:
Originally Posted by Mains52 View Post
Your metal work has been great!! do you have your own metal break? Ive been thinking about buying a small one.
Thanks for the compliment. No break, just using a 4” vise for small stuff. The firewall and steps I brought to a local metal shop.
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=780018 Jason’s 56 build
Jason 56 is offline   Reply With Quote
Old 08-02-2019, 08:58 AM   #6
mongocanfly
Post Whore

 
mongocanfly's Avatar
 
Join Date: May 2015
Location: Alabama
Posts: 14,663
Re: My 56 build

Slick work..,!!....door handle will be a cool mod...
__________________
Mongo...aka Greg

RIP Dad
RIP Jesse

1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598
Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334
Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563
2023 Chevy Z71..daily driver
mongocanfly is offline   Reply With Quote
Old 08-02-2019, 10:32 AM   #7
dsraven
Registered User
 
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,213
Re: My 56 build

they seem kinda spendy but they do last a long time compared to some other stuff. less messy than stripper. like anything though, watch the heat build up on the bigger panels. no worse than a wire wheel and they don't poke wire into your coveralls.....
dsraven is offline   Reply With Quote
Old 08-02-2019, 10:34 AM   #8
dsraven
Registered User
 
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,213
Re: My 56 build

these bristle discs work great too

https://www.eastwood.com/bristle-dis...QaAhBWEALw_wcB
dsraven is offline   Reply With Quote
Old 08-02-2019, 11:45 PM   #9
Jason 56
Registered User
 
Join Date: Nov 2018
Location: Ishpeming, mi
Posts: 625
Re: My 56 build

Quote:
Originally Posted by mongocanfly View Post
Slick work..,!!....door handle will be a cool mod...
Thanks Mongo. I’m hoping they turn work well. Not sure how to build the dish shape for the indent in the body. Figured I’ll grab my hammer n figure it out as I’ve done so far
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=780018 Jason’s 56 build
Jason 56 is offline   Reply With Quote
Old 08-02-2019, 10:30 AM   #10
dsraven
Registered User
 
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,213
Re: My 56 build

these clean and strip discs work great for paint and rust removal. wear glasses and gloves for sure though (found out the hard way with the gloves, if I would only leave those guards in place, lol). available with a drill style arbour or a roloc style as well. bodyshop supply places should have them. I just tried a couple sizes, 4 1/2" electric disc grinder and also air angle die grinder, and they work awesome. strips down to metal in a hurry and not much metal damage/scratches. epoxy primer over top and the scratches fill easy.

https://www.youtube.com/watch?v=Qgvp2ok0PlI
dsraven is offline   Reply With Quote
Old 08-12-2019, 10:09 AM   #11
joedoh
Senior Member
 
joedoh's Avatar
 
Join Date: May 2007
Location: Doodah Kansas
Posts: 7,774
Re: My 56 build

super clean sheetmetal work!
__________________
the mass of men live lives of quiet desperation


if there is a problem, I can have it.

new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393
joedoh is offline   Reply With Quote
Old 08-13-2019, 11:40 PM   #12
Jason 56
Registered User
 
Join Date: Nov 2018
Location: Ishpeming, mi
Posts: 625
Re: My 56 build

Got most of the right side done today. The filler panel in the B-post was the hardest part. Ended up beating the crap out of it to get the right shape. I managed to get it tacked in. You can see the striker in the last 2 pictures. Now to repeat B-post filler panel on the left. Then on to the filler panels on the doors. Hopefully those will be easier
Attached Images
     
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=780018 Jason’s 56 build
Jason 56 is offline   Reply With Quote
Old 08-17-2019, 11:07 PM   #13
Jason 56
Registered User
 
Join Date: Nov 2018
Location: Ishpeming, mi
Posts: 625
Re: My 56 build

A few pictures of the finished B-posts and the door filler panels. Finished the right door panel and just have to weld the left. Then I have to build in the channel that the striker will travel through the door. That shouldn’t be too hard. So far so good
Attached Images
     
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=780018 Jason’s 56 build
Jason 56 is offline   Reply With Quote
Old 08-18-2019, 11:08 AM   #14
Gregski
Post Whore
 
Gregski's Avatar
 
Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,849
Re: My 56 build

wow you really took that cab down to nothing - mad fab skillz
Gregski is offline   Reply With Quote
Old 08-18-2019, 10:50 PM   #15
Jason 56
Registered User
 
Join Date: Nov 2018
Location: Ishpeming, mi
Posts: 625
Re: My 56 build

Finished the fabrication on the C6 door entry system. Just the striker channels left and a door seal lip. You can see the lip drawn out in the second picture. Going to wait on those because I have to replace both lower inner door panels and lower hinge mounts. Want to get the doors to the point of final hang so everything lines up. Moved on to inner valance above the windshield. Found a mouse nest throughout the entire length. Explains why it rusted! Need to clean the tar off the roof and por-15 everything before I weld the panel back in. So I got the left front fender started.
Attached Images
     
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=780018 Jason’s 56 build
Jason 56 is offline   Reply With Quote
Old 08-18-2019, 10:55 PM   #16
Jason 56
Registered User
 
Join Date: Nov 2018
Location: Ishpeming, mi
Posts: 625
Re: My 56 build

Quote:
Originally Posted by Gregski View Post
wow you really took that cab down to nothing - mad fab skillz
Thanks, I didn’t intend on that when I started. It was worse than I thought. In the end the whole lower 12” of the cab has been replaced. I eventually ran out of stuff to replace
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=780018 Jason’s 56 build
Jason 56 is offline   Reply With Quote
Old 08-23-2019, 11:59 PM   #17
Jason 56
Registered User
 
Join Date: Nov 2018
Location: Ishpeming, mi
Posts: 625
Re: My 56 build

A few more pictures of progress. Finished welding the left front fender. Just need to finish making the headlight mount. As you may notice I’m doing away with the blinkers. Going with headlights that have the blinkers built into them. Also put some POR-15 on the ceiling before I weld in the valance. Then the doors come off to replace the lower section on each.
Attached Images
     
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=780018 Jason’s 56 build
Jason 56 is offline   Reply With Quote
Old 08-24-2019, 12:42 AM   #18
dsraven
Registered User
 
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,213
Re: My 56 build

isn't that eyebrow panel available now? not sure about the inside part. it is part of the inner roof panel.

http://www.bowtiebits.com/store/stor...Category_ID=70
dsraven is offline   Reply With Quote
Old 08-24-2019, 09:30 AM   #19
Jason 56
Registered User
 
Join Date: Nov 2018
Location: Ishpeming, mi
Posts: 625
Re: My 56 build

I bought the eyebrow replacement panel. You can get the piece I’m making, but it costs $100. It only comes with the front panel replacement piece. You won’t see it so I made it instead. That bow tie bits site looks to have lots of hard to find items... thanks for the link
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=780018 Jason’s 56 build

Last edited by Jason 56; 08-24-2019 at 09:47 AM.
Jason 56 is offline   Reply With Quote
Old 09-06-2019, 06:47 PM   #20
BC Toy chest
Registered User
 
BC Toy chest's Avatar
 
Join Date: Nov 2010
Location: SoCal
Posts: 914
Re: My 56 build

Fantastic work can't wait to see it when done, Sweet RYDE!!
__________________
I'm not tail-gating, I'm drafting.

http://67-72chevytrucks.com/vboard/s...d.php?t=432758
BC Toy chest is offline   Reply With Quote
Old 09-06-2019, 11:21 PM   #21
Jason 56
Registered User
 
Join Date: Nov 2018
Location: Ishpeming, mi
Posts: 625
Re: My 56 build

Quote:
Originally Posted by BC Toy chest View Post
Fantastic work can't wait to see it when done, Sweet RYDE!!
Thanks BC!
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=780018 Jason’s 56 build
Jason 56 is offline   Reply With Quote
Old 09-06-2019, 11:40 PM   #22
Jason 56
Registered User
 
Join Date: Nov 2018
Location: Ishpeming, mi
Posts: 625
Re: My 56 build

Got both doors started. Tedious job. Lots of alignment issues to take into consideration! Going to coat the inside with POR-15 while I have them open. Also Got the roof and most of the box stripped. Next is the interior and hood so I can prime everything
Attached Images
   
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=780018 Jason’s 56 build
Jason 56 is offline   Reply With Quote
Old 11-13-2019, 12:47 AM   #23
Jason 56
Registered User
 
Join Date: Nov 2018
Location: Ishpeming, mi
Posts: 625
Re: My 56 build

So back to the doors. They were pissing me off so I took a short break to ponder the situation. Also, It was hunting season and time to get everything ready for winter. Just checked the outdoor thermometer and it’s reading 0 tonight. So back to the truck. I couldn’t get the lower replacement panel to flow into the original door skin. I ended up cutting 15” off the door skin and starting over with a sheet of 16 ga. So far so good! I also tore the box apart to start that next.
Attached Images
     
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=780018 Jason’s 56 build
Jason 56 is offline   Reply With Quote
Old 11-13-2019, 11:18 PM   #24
duramax55
Registered User
 
Join Date: Nov 2017
Location: Aubigny
Posts: 212
Re: My 56 build

Jason 56 are you going to roll edges over? wont that be hard to do with 16 gauge steel??
duramax55 is offline   Reply With Quote
Old 11-14-2019, 12:07 AM   #25
Jason 56
Registered User
 
Join Date: Nov 2018
Location: Ishpeming, mi
Posts: 625
Re: My 56 build

Definitely... once I have it tack welded in place
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=780018 Jason’s 56 build
Jason 56 is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:08 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com