big block headers - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**jpgl** · 08-03-2019, 06:13 PM

i am putting together a lowered 1970 chev truck i want to know which big block headers are the best for the price and fit well .

**68bowtie** · 08-03-2019, 06:28 PM

Sanderson BB8’s are claimed to be the best but not the cheapest.

merlin3 · 08-04-2019, 05:57 PM

I also have Sanderson headers they fit great, high quality.

68Gold/white · 08-04-2019, 07:55 PM

jp, I am assuming you want some headers that fit a pickup, and that don't hang below the frame, much???
I don't have an answer but others may...

**jpgl** · 08-05-2019, 03:00 AM

yes i am checking with others before i buy we have poor streets where i live not made for lowered trucks lol ...has any one used patriot headers ?

hdff · 08-06-2019, 09:55 PM

I used hedman mid length on mine. They were coated and fit and look good. Collector is at the frame pointing down, pipe attached and bends parallel to the ground. Sound good too!!!

aerotest · 08-06-2019, 10:30 PM

I have Doug’s headers. Fit ok....not great. Quality is good. The collector alignment is poor so it’s tricky to line up the exhaust.

BCOWANWHEELS · 08-06-2019, 10:50 PM

Look at dorman repop factory iron bbc hi po cast iron manifolds off a vette.

**Steeveedee** · 08-06-2019, 11:40 PM

Quote:

Originally Posted by BCOWANWHEELS

Look at dorman repop factory iron bbc hi po cast iron manifolds off a vette.

Did you use these on a BBC engine in a truck? If/when I replace the engine in my truck I'd rather get manifolds that flow well instead of hearing noisy header "pinging".

BCOWANWHEELS · 08-07-2019, 12:07 AM

If they fit in a car engine bay they will easily fit a truck and they flow great especially with some die grinder work plus they wont heat up the floor. All headers leak.........changing plugs stinks too not to mention starters

Mike C · 08-07-2019, 07:24 AM

I have a set of the big block ‘vette manifolds bolted to my motor on the stand right now. They MIGHT fit in a truck. My plan is to run them even if I have to slightly trim the frame and angle mill and spot face the bolt holes on the manifolds. I think passenger side is where clearance issues will be, but I will find out....

Whenever I can make the swap happen, I’ll post a thread. But they don’t hug the motor as tightly as the passenger car/truck manifolds.

**Steeveedee** · 08-07-2019, 10:25 AM

I'll not be doing any engine replacement any time soon, unless it blows up. I'd like to see the results when you do get to it!

72Cheyenne454 · 08-07-2019, 09:13 PM

I used Patriot Clippster Headers H8013-1, purchased from Summit racing. I've had them now for close to 10yrs with no quality issues.

The only issue I had was during installation and one side... can't remember if it was the drivers or passenger side, but one header tube was contacting my 1972 only factory clamshell style engine mount. I had to trim the clamshell slightly to clear the header, but it wasn't a big deal.

If you're using 71 and earlier big or small block mounts you shouldn't have any issue, but I'm not positive.

https://www.summitracing.com/parts/p...13-1/overview/

Some pictures from when I installed them -

72Cheyenne454 · 08-07-2019, 09:21 PM

A few more pics. My exhaust is completely tucked up above the frame rails.

weq92f · 08-07-2019, 11:32 PM

.
I went with the Hedman elite full length headers for the early big block Chevelle, Camaro... etc..

Ruscal · 08-08-2019, 12:29 AM

I moved my bbc back and down, so didn't know which headers would work. I took a chance and ordered American Racing headers for late sixties Chevelles. They are full length, and use 2" primary tubes. I had to do a little grinding on the passenger upper frame rail for clearance. The primary tubes tucked behind the lower A arm suspension, since the engine was relocated back about 4". (got lucky) I fabricated my own motor mount stands, so no issues there. The headers came with some ball type couplers for the collectors which I cut off and tigged on SS V clamps. The collectors hang about 2" below the frame because my engine is dropped about 1". The truck is static dropped for a nice stance, and I have not touched the headers yet on speed bumps. So far working well. Headers are stainless steel raw mill finish. I gave them a little Scotchbrite stroking.
Russ

68is4me · 08-08-2019, 09:29 AM

Quote:

Originally Posted by BCOWANWHEELS

If they fit in a car engine bay they will easily fit a truck and they flow great especially with some die grinder work plus they wont heat up the floor. All headers leak.........changing plugs stinks too not to mention starters

I don't think the vette ones fit. I think Randy500 tried and had a write up about that, I believe they hit the engine mounts.

68is4me · 08-08-2019, 09:32 AM

I am running Sanderson's and fit great. So far no leaks, and I just change plugs last night with no problems.

08-03-2019, 06:13 PM	#1
jpgl Junior Member Join Date: May 2016 Location: Regina, Saskatchewan Posts: 83	big block headers i am putting together a lowered 1970 chev truck i want to know which big block headers are the best for the price and fit well .

08-03-2019, 06:28 PM	#2
68bowtie Senior Member Join Date: Jan 2007 Location: Turlock, CA Posts: 8,553	Re: big block headers Sanderson BB8’s are claimed to be the best but not the cheapest. __________________ Please help my sister in law with her battle with cancer https://gofund.me/902f6fce Survivor "Lil’ Mint" (67 c10 40k mile light green original paint) Project "C10 Fever" (68 factory black 396 swb) Project "Little Sister" (70 c10 blue original paint refresh) Project "Blue Bomb" (70 c30 blue original paint refresh) SOLD Project "Vitamin C" (71 c10 orange original paint refresh) SOLD

08-04-2019, 05:57 PM	#3
merlin3 Registered User Join Date: Aug 2012 Location: nantucket,ma Posts: 230	Re: big block headers I also have Sanderson headers they fit great, high quality.

08-04-2019, 07:55 PM	#4
68Gold/white Registered User Join Date: Sep 2011 Location: Ark City, Kansas Posts: 3,319	Re: big block headers jp, I am assuming you want some headers that fit a pickup, and that don't hang below the frame, much??? I don't have an answer but others may...

08-05-2019, 03:00 AM	#5
jpgl Junior Member Join Date: May 2016 Location: Regina, Saskatchewan Posts: 83	Re: big block headers yes i am checking with others before i buy we have poor streets where i live not made for lowered trucks lol ...has any one used patriot headers ?

08-06-2019, 09:55 PM	#6
hdff Registered User Join Date: Apr 2007 Location: pasadena,TEXAS Posts: 880	Re: big block headers I used hedman mid length on mine. They were coated and fit and look good. Collector is at the frame pointing down, pipe attached and bends parallel to the ground. Sound good too!!! __________________ 1971 Cheyenne SWB 402BB, 700R4, 3.73 posi, PS, PB, A/C, Tilt, Tach "Wanda" Don't argue with idiots, People watching may not be able to tell the difference... There's someone in my head........But it's not me...... cheap tricks thread great info here!! http://67-72chevytrucks.com/vboard/s...d.php?t=489394

08-06-2019, 10:30 PM	#7
aerotest Registered User Join Date: Jan 2018 Location: TN Posts: 104	Re: big block headers I have Doug’s headers. Fit ok....not great. Quality is good. The collector alignment is poor so it’s tricky to line up the exhaust. __________________ 1969 C10 Suburban Custom (Factory 396/TH400, survivor with no rust)

08-06-2019, 10:50 PM	#8
BCOWANWHEELS Registered User Join Date: Nov 2006 Location: KINGSPORT,TN. Posts: 3,035	Re: big block headers Look at dorman repop factory iron bbc hi po cast iron manifolds off a vette. __________________ I BELIEVE IN JOHN 3:16

08-07-2019, 12:07 AM	#10
BCOWANWHEELS Registered User Join Date: Nov 2006 Location: KINGSPORT,TN. Posts: 3,035	Re: big block headers If they fit in a car engine bay they will easily fit a truck and they flow great especially with some die grinder work plus they wont heat up the floor. All headers leak.........changing plugs stinks too not to mention starters __________________ I BELIEVE IN JOHN 3:16

08-07-2019, 07:24 AM	#11
Mike C Registered User Join Date: Dec 1999 Location: Austin, TX, USA Posts: 7,715	Re: big block headers I have a set of the big block ‘vette manifolds bolted to my motor on the stand right now. They MIGHT fit in a truck. My plan is to run them even if I have to slightly trim the frame and angle mill and spot face the bolt holes on the manifolds. I think passenger side is where clearance issues will be, but I will find out.... Whenever I can make the swap happen, I’ll post a thread. But they don’t hug the motor as tightly as the passenger car/truck manifolds. __________________ 44 Willys MB 52 M38A1 64 Corvette Coupe 68 Camaro 'vert LT1 & TH700 69 Z/28 355 12.6's @110 69 Chevy Short Step 4 1/2"/7" drop 72 Jimmy 4WD 4spd 4" & 35's 02 GMC 2500HD 4x4 Duramax

08-07-2019, 10:25 AM	#12
Steeveedee Who Changed This? Join Date: Jan 2013 Location: Simi Valley, CA Posts: 10,280	Re: big block headers I'll not be doing any engine replacement any time soon, unless it blows up. I'd like to see the results when you do get to it! __________________ ~Steven '70 Chevy 3/4T Longhorn CST 402/400/3.56 Custom Camper Simi Valley, CA

08-07-2019, 09:13 PM	#13
72Cheyenne454 Registered User Join Date: Apr 2007 Location: San Diego Posts: 453	Re: big block headers I used Patriot Clippster Headers H8013-1, purchased from Summit racing. I've had them now for close to 10yrs with no quality issues. The only issue I had was during installation and one side... can't remember if it was the drivers or passenger side, but one header tube was contacting my 1972 only factory clamshell style engine mount. I had to trim the clamshell slightly to clear the header, but it wasn't a big deal. If you're using 71 and earlier big or small block mounts you shouldn't have any issue, but I'm not positive. https://www.summitracing.com/parts/p...13-1/overview/ Some pictures from when I installed them - Attached Images Last edited by 72Cheyenne454; 08-07-2019 at 09:22 PM.

08-07-2019, 09:21 PM	#14
72Cheyenne454 Registered User Join Date: Apr 2007 Location: San Diego Posts: 453	Re: big block headers A few more pics. My exhaust is completely tucked up above the frame rails. Attached Images

08-07-2019, 11:32 PM	#15
weq92f Registered User Join Date: Oct 2016 Location: Dallas Texas Posts: 3,016	Re: big block headers . I went with the Hedman elite full length headers for the early big block Chevelle, Camaro... etc.. Attached Images __________________ 67 C10 fleet fuel injected '70 402, 700r4, 3.73 posi 07 335 sport turbo 6sp 94 Trans Am GT LT1 6sp posi -- sold after 22yrs 99 540 sport V8 6sp -- sold 73 240z L24 4sp -- given to friend 68 C10 step 350/350 3.73 open -- sold

08-08-2019, 12:29 AM	#16
Ruscal Registered User Join Date: Jun 2013 Location: Carlsbad, California Posts: 165	Re: big block headers I moved my bbc back and down, so didn't know which headers would work. I took a chance and ordered American Racing headers for late sixties Chevelles. They are full length, and use 2" primary tubes. I had to do a little grinding on the passenger upper frame rail for clearance. The primary tubes tucked behind the lower A arm suspension, since the engine was relocated back about 4". (got lucky) I fabricated my own motor mount stands, so no issues there. The headers came with some ball type couplers for the collectors which I cut off and tigged on SS V clamps. The collectors hang about 2" below the frame because my engine is dropped about 1". The truck is static dropped for a nice stance, and I have not touched the headers yet on speed bumps. So far working well. Headers are stainless steel raw mill finish. I gave them a little Scotchbrite stroking. Russ __________________ RC



Register or Log In To remove these advertisements.

08-08-2019, 09:32 AM	#18
68is4me Registered User Join Date: Jun 2014 Location: lakefield,mn Posts: 566	Re: big block headers I am running Sanderson's and fit great. So far no leaks, and I just change plugs last night with no problems. __________________ 68 c10 swb stepper 68 c10 swb stepper 67 c10 lwb 06 gmc duramax

Register or Log In To remove these advertisements.