The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Paint & Bodywork

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 07-22-2020, 11:32 PM   #1
dag19
Registered User
 
dag19's Avatar
 
Join Date: Apr 2010
Location: Austin TX
Posts: 135
Order of Operations - Cab repair/sandblast

I would like a little expert insight on what the proper order of operations is when it comes to repairing the rusty cab corners, rocker panels, and floor sections. Should one sandblast the cab down to bare metal in order to see all the rust first? Or should one just get out the grinder, clean up all the paint, and start cutting out rust and replacing panels?

Ultimately, I would like to get the cab down to bare metal with a wet sandblast so I can prime and paint the interior. It might be 3 or 4 months time during this whole process. Let me know what route is best!
dag19 is offline   Reply With Quote
Old 07-23-2020, 09:35 AM   #2
Davidf
Registered User
 
Join Date: Nov 2014
Location: Austin
Posts: 749
Re: Order of Operations - Cab repair/sandblast

I am currently in the home stretch of doing all these repairs on my '71 long. I did not worry about removing any paint because I could see where it was rusting. I immediately started right in at removing the rusty rockers, inner rockers, hinge pillars and kick panels.

I removed the entire inner and outer rockers because they were completely gone. For the other areas I just removed as much material as necessary to get solid metal. So, A-pillar bottoms, kick panel bottoms, floor next to kick panel. And a few patches in the floor next to inner rockers as necessary. Oh, and B-pillar bottoms. Cab corners I patched up with homemade patches. I also made the kick panel bottoms by using cut out metal as a template/guide.

Then I sanded back the paint to a feather edge near the repairs, primed (x2), sealed, finish coat

Did the same to the door bottoms. Also, if superficial rust existed where I did not cut out metal, I used a phosphoric acid water mixture to neutralize the rust (then topcoated).

In the image you can see that I epoxy primed the cab floor (which I did not replace)...I simply used a scouring pad on my angle grinder to get rid of glue and other junk. Then I primed.

Currently prepping fenders (wings for those across the pond) for paint. Doors and cab interior are 100% done. FYI, I used Precision press on door seals and they are perfect and I do not have to slam the doors. I was careful to ensure the door was positioned in the door jamb uniformly before calling it good. This ensured the door seal was compressed even all around for good shutting doors.

Good luck.


Last edited by Davidf; 07-23-2020 at 09:41 AM.
Davidf is offline   Reply With Quote
Old 07-24-2020, 02:31 AM   #3
dag19
Registered User
 
dag19's Avatar
 
Join Date: Apr 2010
Location: Austin TX
Posts: 135
Re: Order of Operations - Cab repair/sandblast

Thanks for all the good info David, looks like you're on the right track! How long did it take you to get through your cab? Where did you get your door seals at?

Would it even be worth wet sandblasting my cab after I get the rust removed? Mainly for paint prep. I'm not sure how long it'd take for the surface rust to form again. I'm in a fairly dry climate here in western NE.
dag19 is offline   Reply With Quote
Old 07-24-2020, 08:45 AM   #4
mongocanfly
Post Whore

 
mongocanfly's Avatar
 
Join Date: May 2015
Location: Alabama
Posts: 14,663
Re: Order of Operations - Cab repair/sandblast

on mine I did it both ways...the areas that obviously needed replaced or worked on I did prior to sandblasting....
then the blaster will always reveal something you didn't or couldn't see before...
so what I did was ..
repair visible rot/cracks/broken welds/etc
sandblast
epoxy prime..
then fix the spots the blaster revealed
and epoxy prime again..
then do bodywork and epoxy over that
then high build and paint..
some of these steps were repeated several times..

make sure you use a blaster with body panel experience...as easily as they can clean a panel, they can also ruin it
__________________
Mongo...aka Greg

RIP Dad
RIP Jesse

1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598
Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334
Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563
2023 Chevy Z71..daily driver
mongocanfly is offline   Reply With Quote
Old 07-24-2020, 10:37 PM   #5
Peanut74
Registered User
 
Join Date: May 2018
Location: Prattville, AL
Posts: 611
Re: Order of Operations - Cab repair/sandblast

I blasted mine first so I could make sure I could see all the areas that needed work. I'm glad I did as there was a lot of bondo filled rust areas. You can see the order I did mine if you look at my thread "order of rust repair". I basically asked the same question you are.

Ditto, find a blaster that as experience with blasting automotive panels. Found out the hard way on my 89 Toyota pickup. He overheated the metal and I now have warped panel under the side window.
Peanut74 is offline   Reply With Quote
Old 07-25-2020, 05:08 PM   #6
LS short box
Registered User
 
Join Date: Jun 2015
Location: Carlos MN
Posts: 2,107
Re: Order of Operations - Cab repair/sandblast

I've done a few "frame off" restos and I've had good luck with removing all the old paint with air craft paint stripper on the big panels but staying away from all seams and edges. Then I use a DA sander and fiber disc on right angle die grinder to take off the rest. Around the edges I use my 30 pound pressure sand blaster. Parts like the door pillars and around the window openings.
I would be very nervous about anyone using a high pressure commercial grade sand blaster on any of the large panels.
LS short box is offline   Reply With Quote
Old 07-28-2020, 01:50 AM   #7
projectking
Registered User
 
projectking's Avatar
 
Join Date: Oct 2006
Location: Orland Park Il
Posts: 2,041
Re: Order of Operations - Cab repair/sandblast

I like to cut out the bad first to expose the areas behind for blasting and epoxy primer.
__________________
68 GMC C3500 Longhorn DRW
67 Chevy C10 LWB
90 Mustang Gt
90 Mustang Notchback
projectking is offline   Reply With Quote
Old 08-02-2020, 12:32 PM   #8
pdxhall
Senior Member
 
pdxhall's Avatar
 
Join Date: Mar 2011
Location: Tucson, Arizona
Posts: 2,082
Re: Order of Operations - Cab repair/sandblast

I repaired most of my cab before blasting. I then blasted the entire cab ..and epoxy primed. The fenders, hood, and other parts were blasted and then patched and epoxy primed. I use crushed glass as my blasting media. On large panels, I stripped by hand. I still have the doors to do. I will cut out the rust on the bottoms and then before patching I will blast the insides of the doors, then epoxy prime the inside of the doors before patching the bottom.
__________________
Sanity'66
http://67-72chevytrucks.com/vboard/s...d.php?t=515110
Long bed, Fleetside, Small back window

I've Done So Much, With So Little, For So Long, That Now I Can Do Anything With Nothing.
pdxhall is offline   Reply With Quote
Reply

Bookmarks

Tags
cab, rust repair, sandblast


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:05 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com