Can I lower the ECE 4/6 drop kit further? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

thallman · 01-25-2021, 01:40 AM

I have the ECE 4/6 drop kit currently, however, I was wanting to go lower in the front. I was wondering if I could swap out lowering springs to achieve this? It came with 1.5" drop springs, but I saw where Performance Online has drop springs in 2", 3", and 4" drops. If I bought the 4" drop springs that would theoretically get me from a 4" drop in the front to a 6.5" drop in the front. Is it that simple or is there more to it?

Thanks.

Tx Firefighter · 01-25-2021, 07:14 AM

Yes, you can replace the current ECE 1.5 springs with something more aggressive. I'd really urge you not to go below a 3 inch spring though. That's 5.5 total drop and that's quite a lot. Beyond that you might look into options like crossmember mods or even a dropmember setup.

SCOTI · 01-25-2021, 10:35 AM

x2.

The shorter the coil spring, the less travel there is & the closer the contact points up front come to the road surface.

Measure your lower a-arm @ it's current lowest spot.
Measure the lower a-arm mounting shaft pivot points.

How far is it off the road surface now?

thallman · 01-25-2021, 11:58 AM

Thanks for the quick reply. I will go for the 3" lowering springs then. I was thinking about a PB dropmember, however, I think the 3" lowering springs will give me a good stance, and will be a lot less work given it the rest of the ECE kit is already installed.

Thanks again.

thallman · 01-25-2021, 11:59 AM

Quote:

Originally Posted by SCOTI

x2.

The shorter the coil spring, the less travel there is & the closer the contact points up front come to the road surface.

Measure your lower a-arm @ it's current lowest spot.
Measure the lower a-arm mounting shaft pivot points.

How far is it off the road surface now?

I'm not sure, it is on an uneven surface at the moment.

SCOTI · 01-25-2021, 12:13 PM

Quote:

Originally Posted by thallman

I'm not sure, it is on an uneven surface at the moment.

Then measure the closer of the sides. That's what you'll be dealing w/when driving (roads are never always flat).

I've always had lowered trucks/cars. They suck to drive when they're lowered in such a way that compromises the 'ability to drive'. Constantly bottoming out. A-arms impacting uneven road surfaces. Tires buzzing the sheet metal.

Driving something low but still has clearance should be the goal.

01-25-2021, 01:40 AM	#1
thallman Registered User Join Date: Dec 2012 Location: Stigler, OK Posts: 3	Can I lower the ECE 4/6 drop kit further? I have the ECE 4/6 drop kit currently, however, I was wanting to go lower in the front. I was wondering if I could swap out lowering springs to achieve this? It came with 1.5" drop springs, but I saw where Performance Online has drop springs in 2", 3", and 4" drops. If I bought the 4" drop springs that would theoretically get me from a 4" drop in the front to a 6.5" drop in the front. Is it that simple or is there more to it? Thanks.

01-25-2021, 07:14 AM	#2
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Re: Can I lower the ECE 4/6 drop kit further? Yes, you can replace the current ECE 1.5 springs with something more aggressive. I'd really urge you not to go below a 3 inch spring though. That's 5.5 total drop and that's quite a lot. Beyond that you might look into options like crossmember mods or even a dropmember setup. __________________ I'm on the Instagram- @Gearhead_Kevin

01-25-2021, 10:35 AM	#3
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,041	Re: Can I lower the ECE 4/6 drop kit further? x2. The shorter the coil spring, the less travel there is & the closer the contact points up front come to the road surface. Measure your lower a-arm @ it's current lowest spot. Measure the lower a-arm mounting shaft pivot points. How far is it off the road surface now? __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

01-25-2021, 11:58 AM	#4
thallman Registered User Join Date: Dec 2012 Location: Stigler, OK Posts: 3	Re: Can I lower the ECE 4/6 drop kit further? Thanks for the quick reply. I will go for the 3" lowering springs then. I was thinking about a PB dropmember, however, I think the 3" lowering springs will give me a good stance, and will be a lot less work given it the rest of the ECE kit is already installed. Thanks again.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.