1972 Highlander (Forum Truck) - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**HeloCrewChief** · 12-25-2021, 05:27 PM

I've been slammed busy at work and was out of the state for work for a bit. Moving along but, still slower than I would like. I'm almost ready to install inner fenders, core support, grille, bumpers, and hood. Doing a few final checks to make sure I have everything buttoned up on the engine before I install those parts. I wanted to do some day 2 hickey items like differential covers etc. but, I may hold off until the truck is done before spending money on those. I found some subdued differential covers, transmission pan, and flywheel cover I've liked using on other trucks. I also did a new engine compartment wiring harness. Bluetooth radio is in. Front carpet, console, sill plates etc. Driveshafts are in. New heater core and all the HVAC tubing. I had the emissions lines in the back remade by Williams Oil Filter in Tacoma, WA. Hood hinges rebuilt by Wilson Antique Auto Parts. Tilt column, console, and instrument cluster rebuilt by Randy here in Tacoma. Used the van shifter arm as it fits better with the 15" wheel. Exhaust manifolds were coated by Performance Coatings in Auburn, WA. Lots of other little details I'm forgetting. It is scary how close I'm getting. I always seem to drag my feet at the end because I enjoy the building aspect most.

**HeloCrewChief** · 12-25-2021, 05:35 PM

The door panels are original. I was able to clean them up with SEM soap and no need to dye them. I got my upholstery in from SMS. I ordered the front and rear covers back in the spring and got them last month. Need to get those installed once I get my seat foam in from ACI. It is a challenger building anything with the delays right now.

**HeloCrewChief** · 12-25-2021, 05:42 PM

Some more pictures

**HeloCrewChief** · 12-25-2021, 05:43 PM

some more pictures

**Ol Blue K20** · 12-25-2021, 06:05 PM

Quote:

Originally Posted by HeloCrewChief

some more pictures

Looks great!

**HeloCrewChief** · 01-15-2022, 08:46 PM

Quote:

Originally Posted by Ol Blue K20

Looks great!

Thanks Dale. Your Dually went to a good home. I let it go to another truck guy. He flew in and drove it home to Texas. Even picked up a C10 project along the way and towed it home. Once I calculated paint and all the other things I wanted to do to it, I figured it was best to send it down the road to a guy that had the time. Too many projects on my plate.
Posted via Mobile Device

**HeloCrewChief** · 01-15-2022, 08:52 PM

Got the roll bar in. It’s a motor city K5 piece and I’m happy with the look and quality. I was shorted 4 mounting bolts but, a quick run to the hardware store will solve that. The CST rear panels are in. Wasn’t too bad locating all the brackets back into position since the holes had to be located and drilled since the reproduction bedsides/ floor don’t have them. Next challenge will be the seat mounting and spare tire carrier. I also painted the dash top as the windshield is going in soon.
Posted via Mobile Device

**Orange71shorty** · 01-15-2022, 10:01 PM

Quote:

Originally Posted by HeloCrewChief

Got the roll bar in. It’s a motor city K5 piece and I’m happy with the look and quality. I was shorted 4 mounting bolts but, a quick run to the hardware store will solve that. The CST rear panels are in. Wasn’t too bad locating all the brackets back into position since the holes had to be located and drilled since the reproduction bedsides/ floor don’t have them. Next challenge will be the seat mounting and spare tire carrier. I also painted the dash top as the windshield is going in soon.
Posted via Mobile Device

Where did you source the rear CST panels, and are you happy with the quality?

**HeloCrewChief** · 01-15-2022, 10:12 PM

I think I got them from Brothers a while back. I believe the brand is PUI. The fit was about as good as reproduction parts fit. They’re much puffier than original but, most reproduction door panels I’ve used are puffier than originals. I've used Chevelle, Nova, and Camaro PUI door panels and they are all overstuffed. I think Legendary interiors makes the nicest stuff but, not sure if they make the CST panels. Not many options though as finding originals is not going to happen.

**Ol Blue K20** · 01-15-2022, 10:23 PM

Quote:

Originally Posted by HeloCrewChief

Got the roll bar in. It’s a motor city K5 piece and I’m happy with the look and quality. I was shorted 4 mounting bolts but, a quick run to the hardware store will solve that. The CST rear panels are in. Wasn’t too bad locating all the brackets back into position since the holes had to be located and drilled since the reproduction bedsides/ floor don’t have them. Next challenge will be the seat mounting and spare tire carrier. I also painted the dash top as the windshield is going in soon.
Posted via Mobile Device

Thanks for letting me know. It deserves to be loved!

**Orange71shorty** · 01-15-2022, 11:59 PM

Quote:

Originally Posted by HeloCrewChief

I think I got them from Brothers a while back. I believe the brand is PUI. The fit was about as good as reproduction parts fit. They’re much puffier than original but, most reproduction door panels I’ve used are puffier than originals. I've used Chevelle, Nova, and Camaro PUI door panels and they are all overstuffed. I think Legendary interiors makes the nicest stuff but, not sure if they make the CST panels. Not many options though as finding originals is not going to happen.

Thanks, the rig is looking awesome

**HeloCrewChief** · 01-18-2022, 05:46 PM

Condenser and some of the A/C hoses and lines are in. Also the windshield and wipers are on.

**IronCanine** · 01-18-2022, 06:10 PM

Looking good! Love the progress, love the build (and love the shop).

**Ol Blue K20** · 01-18-2022, 10:05 PM

Quote:

Originally Posted by IronCanine

Looking good! Love the progress, love the build (and love the shop).

I agree with all points!

**BigBird05** · 01-24-2022, 12:44 PM

In all of your photos do you have one that shows the bottom ( drain ) part of the A/C housing?

**HeloCrewChief** · 01-24-2022, 04:38 PM

Quote:

Originally Posted by BigBird05

In all of your photos do you have one that shows the bottom ( drain ) part of the A/C housing?

BigBird,

This is the only picture I could find. Not the best.

**BigBird05** · 01-24-2022, 04:40 PM

Thanks

Bmdully · 01-29-2022, 12:39 AM

Gotta asked Oliver, where did you find hose clamps to match the paint? Looking at the picture of the fuel tank.

**HeloCrewChief** · 02-02-2022, 02:16 PM

Quote:

Originally Posted by Bmdully

Gotta asked Oliver, where did you find hose clamps to match the paint? Looking at the picture of the fuel tank.

Brandon, not too sue what you are seeing. Guessing it must be some sort of reflection. The gas tank straps are originals that I powder coated. Clamps are just regular worm gear style from NAPA. Hope all is well. I have a buddy building a 70' K10 Suburban now. Sure do miss that K20. It drove so well. Have a feeling I wont love how squirly these Blazers are.

**HeloCrewChief** · 02-02-2022, 02:18 PM

Brandon,

Just looked back through my pictures. I see what you are talking about now. I got those clamps at Mclendons in their hardware section. Just a weird OCD thing but, trying to match up all the clamps and clips in the correct colors they were originally. I've had to paint some to match as well.

**YellowK5** · 02-02-2022, 08:04 PM

Really nice looking Blazer..great work

Bmdully · 02-04-2022, 01:07 AM

Well it’s looking great buddy. We need to organize some WA cruise when she’s finished.

**HeloCrewChief** · 04-13-2022, 11:12 AM

Back seat, carpet, spare tire in. Just need to source a spare tire bolt.

**DeadheadNM** · 04-13-2022, 01:17 PM

Boom! Nice CB too...

**Ol Blue K20** · 04-13-2022, 09:41 PM

It's looking great Oliver! I love it!

12-25-2021, 05:27 PM	#51
HeloCrewChief Senior Member Join Date: Aug 2010 Location: North Alabama Posts: 1,039	Re: 1972 Highlander (Forum Truck) I've been slammed busy at work and was out of the state for work for a bit. Moving along but, still slower than I would like. I'm almost ready to install inner fenders, core support, grille, bumpers, and hood. Doing a few final checks to make sure I have everything buttoned up on the engine before I install those parts. I wanted to do some day 2 hickey items like differential covers etc. but, I may hold off until the truck is done before spending money on those. I found some subdued differential covers, transmission pan, and flywheel cover I've liked using on other trucks. I also did a new engine compartment wiring harness. Bluetooth radio is in. Front carpet, console, sill plates etc. Driveshafts are in. New heater core and all the HVAC tubing. I had the emissions lines in the back remade by Williams Oil Filter in Tacoma, WA. Hood hinges rebuilt by Wilson Antique Auto Parts. Tilt column, console, and instrument cluster rebuilt by Randy here in Tacoma. Used the van shifter arm as it fits better with the 15" wheel. Exhaust manifolds were coated by Performance Coatings in Auburn, WA. Lots of other little details I'm forgetting. It is scary how close I'm getting. I always seem to drag my feet at the end because I enjoy the building aspect most. Attached Images __________________ 1970 C10 to K20 conversion 1974 GMC Jimmy 1968 50th Anniversary Short Bed 1968 Chevelle 1964 Comet Caliente 1990 W250 Cummins

12-25-2021, 05:35 PM	#52
HeloCrewChief Senior Member Join Date: Aug 2010 Location: North Alabama Posts: 1,039	Re: 1972 Highlander (Forum Truck) The door panels are original. I was able to clean them up with SEM soap and no need to dye them. I got my upholstery in from SMS. I ordered the front and rear covers back in the spring and got them last month. Need to get those installed once I get my seat foam in from ACI. It is a challenger building anything with the delays right now. Attached Images __________________ 1970 C10 to K20 conversion 1974 GMC Jimmy 1968 50th Anniversary Short Bed 1968 Chevelle 1964 Comet Caliente 1990 W250 Cummins

12-25-2021, 05:42 PM	#53
HeloCrewChief Senior Member Join Date: Aug 2010 Location: North Alabama Posts: 1,039	Re: 1972 Highlander (Forum Truck) Some more pictures Attached Images __________________ 1970 C10 to K20 conversion 1974 GMC Jimmy 1968 50th Anniversary Short Bed 1968 Chevelle 1964 Comet Caliente 1990 W250 Cummins

12-25-2021, 05:43 PM	#54
HeloCrewChief Senior Member Join Date: Aug 2010 Location: North Alabama Posts: 1,039	Re: 1972 Highlander (Forum Truck) some more pictures Attached Images __________________ 1970 C10 to K20 conversion 1974 GMC Jimmy 1968 50th Anniversary Short Bed 1968 Chevelle 1964 Comet Caliente 1990 W250 Cummins

01-15-2022, 08:52 PM	#57
HeloCrewChief Senior Member Join Date: Aug 2010 Location: North Alabama Posts: 1,039	Got the roll bar in. It’s a motor city K5 piece and I’m happy with the look and quality. I was shorted 4 mounting bolts but, a quick run to the hardware store will solve that. The CST rear panels are in. Wasn’t too bad locating all the brackets back into position since the holes had to be located and drilled since the reproduction bedsides/ floor don’t have them. Next challenge will be the seat mounting and spare tire carrier. I also painted the dash top as the windshield is going in soon. Posted via Mobile Device Attached Images

01-15-2022, 10:12 PM	#59
HeloCrewChief Senior Member Join Date: Aug 2010 Location: North Alabama Posts: 1,039	Re: 1972 Highlander (Forum Truck) I think I got them from Brothers a while back. I believe the brand is PUI. The fit was about as good as reproduction parts fit. They’re much puffier than original but, most reproduction door panels I’ve used are puffier than originals. I've used Chevelle, Nova, and Camaro PUI door panels and they are all overstuffed. I think Legendary interiors makes the nicest stuff but, not sure if they make the CST panels. Not many options though as finding originals is not going to happen. __________________ 1970 C10 to K20 conversion 1974 GMC Jimmy 1968 50th Anniversary Short Bed 1968 Chevelle 1964 Comet Caliente 1990 W250 Cummins Last edited by HeloCrewChief; 01-15-2022 at 11:14 PM.

01-18-2022, 05:46 PM	#62
HeloCrewChief Senior Member Join Date: Aug 2010 Location: North Alabama Posts: 1,039	Re: 1972 Highlander (Forum Truck) Condenser and some of the A/C hoses and lines are in. Also the windshield and wipers are on. Attached Images __________________ 1970 C10 to K20 conversion 1974 GMC Jimmy 1968 50th Anniversary Short Bed 1968 Chevelle 1964 Comet Caliente 1990 W250 Cummins

01-18-2022, 06:10 PM	#63
IronCanine I'm trying.... Join Date: Oct 2013 Location: Athens, GA Posts: 2,550	Re: 1972 Highlander (Forum Truck) Looking good! Love the progress, love the build (and love the shop). __________________ 1970 Blazer http://67-72chevytrucks.com/vboard/s...d.php?t=645076 1969 K10 SWB CST http://67-72chevytrucks.com/vboard/s...52#post8520352 1971 K20 Z84 https://67-72chevytrucks.com/vboard/...90#post9047290 1946 B.F. Avery Model A Tractor http://67-72chevytrucks.com/vboard/s...55#post8292555 "Sometimes I wonder if zander208 was even real..."

01-24-2022, 12:44 PM	#65
BigBird05 Senior Member Join Date: Aug 2019 Location: Cheraw Posts: 1,305	Re: 1972 Highlander (Forum Truck) In all of your photos do you have one that shows the bottom ( drain ) part of the A/C housing?

01-24-2022, 04:40 PM	#67
BigBird05 Senior Member Join Date: Aug 2019 Location: Cheraw Posts: 1,305	Re: 1972 Highlander (Forum Truck) Thanks

01-29-2022, 12:39 AM	#68
Bmdully Registered User Join Date: Dec 2013 Location: Seattle, wa Posts: 31	Re: 1972 Highlander (Forum Truck) Gotta asked Oliver, where did you find hose clamps to match the paint? Looking at the picture of the fuel tank.

02-02-2022, 02:18 PM	#70
HeloCrewChief Senior Member Join Date: Aug 2010 Location: North Alabama Posts: 1,039	Re: 1972 Highlander (Forum Truck) Brandon, Just looked back through my pictures. I see what you are talking about now. I got those clamps at Mclendons in their hardware section. Just a weird OCD thing but, trying to match up all the clamps and clips in the correct colors they were originally. I've had to paint some to match as well. __________________ 1970 C10 to K20 conversion 1974 GMC Jimmy 1968 50th Anniversary Short Bed 1968 Chevelle 1964 Comet Caliente 1990 W250 Cummins

02-02-2022, 08:04 PM	#71
YellowK5 Active Member Join Date: Jun 2021 Location: Rancho Cucamonga California Posts: 170	Re: 1972 Highlander (Forum Truck) Really nice looking Blazer..great work

02-04-2022, 01:07 AM	#72
Bmdully Registered User Join Date: Dec 2013 Location: Seattle, wa Posts: 31	Re: 1972 Highlander (Forum Truck) Well it’s looking great buddy. We need to organize some WA cruise when she’s finished.

04-13-2022, 11:12 AM	#73
HeloCrewChief Senior Member Join Date: Aug 2010 Location: North Alabama Posts: 1,039	Re: 1972 Highlander (Forum Truck) Back seat, carpet, spare tire in. Just need to source a spare tire bolt. Attached Images __________________ 1970 C10 to K20 conversion 1974 GMC Jimmy 1968 50th Anniversary Short Bed 1968 Chevelle 1964 Comet Caliente 1990 W250 Cummins



Register or Log In To remove these advertisements.

04-13-2022, 01:17 PM	#74
DeadheadNM Carpe manana Join Date: Dec 2010 Location: Eau Claire, WI Posts: 12,336	Re: 1972 Highlander (Forum Truck) Boom! Nice CB too... __________________ 1972 K5 CST Highlander Blazer: http://67-72chevytrucks.com/vboard/s...d.php?t=708547 1972 K20 Cheyenne Super: http://67-72chevytrucks.com/vboard/s...d.php?t=528308 Members met: ORANGBLAZ, 2003 silverado, MikeCofield, BB72CHEVKT, Duncan&Son, Sameyrasmea72, THENEWMEXICAN, HotRod C/10, brianthelion02, Sport/Truck, ryanroo, michael bustamante, Dirt's72, Already Gone, WestButteTruck, 57taskforce, Moreyel, painterljp, AASmedic, SoCoC10, Lumaestas, carbuff382, Chevyland

04-13-2022, 09:41 PM	#75
Ol Blue K20 Proprietor of Dale's Corner Join Date: Nov 2012 Location: Vacaville , CA Posts: 15,922	Re: 1972 Highlander (Forum Truck) It's looking great Oliver! I love it! __________________ "Some Days Chickens And Some Days Feathers" Dale XNGH ECV Sam Brannan 1004 R.I.P. 67ChevyRedneck R.I.P. Grumpy Old Man

Register or Log In To remove these advertisements.