![]() |
![]() |
#1 |
New Member
![]() Join Date: Aug 2022
Location: Milton TN
Posts: 13
|
Taillight trim
Trying to replace the trim around the tailights on a 67. Bought the new trim and clips from LMC but for the life of me I don’t see how these clips can be used. They were included with the order but I think they’re too big for the hole and the trim itself.
Is there a different clip for these? |
![]() |
![]() |
![]() |
#2 |
Always on the hunt...
![]() Join Date: Sep 2006
Location: Portland, OR.
Posts: 5,603
|
Re: Taillight trim
Have a look at post #22/#23 of the below linked thread on this subject, it shows the 69-72 style tail light bezels but the 67-68 tail light trim used the same push in clips. Mel
![]() https://www.67-72chevytrucks.com/vbo...d.php?t=698982
__________________
***For any return/past customers & friends*** Before sending of any funds, please wait for a confirmed total and instructions for sending as our payment account info has been changed as of Jan. 2023. Thanks... |
![]() |
![]() |
![]() |
#3 |
Always on the hunt...
![]() Join Date: Sep 2006
Location: Portland, OR.
Posts: 5,603
|
Re: Taillight trim
Also, if you you decide against using/fighting the repro clips, we recently pulled some GM NOS tail light bezel mounting clips out for another member and currently have a couple of extra sets available ready to ship, see post #68 in below linked thread if interested. Mel
![]() http://67-72chevytrucks.com/vboard/s...=698537&page=3 .
__________________
***For any return/past customers & friends*** Before sending of any funds, please wait for a confirmed total and instructions for sending as our payment account info has been changed as of Jan. 2023. Thanks... |
![]() |
![]() |
![]() |
#4 |
New Member
![]() Join Date: Aug 2022
Location: Milton TN
Posts: 13
|
Re: Taillight trim
Thanks, I’ll PM you later.
|
![]() |
![]() |
![]() |
#5 |
Senior Member
![]() Join Date: Mar 2015
Location: washington
Posts: 2,234
|
Re: Taillight trim
I highly recommend the OEM clips.
I didn't have access to OEM when I installed mine. Some suggestions; Confirm you can install the clips, into the hole, before attaching them to the aluminum. You don't have to push them in all the way. If you do they may be difficult to remove. A slight dab of grease on the clip will help more than you would think. If the clips you received don't seem correct try another vendor, they are not all the same. If fact they vary a lot in design. The first design I used were junk. Sorry I don't remember the source of the one that actually functioned. Don't push too hard on the aluminum to install. I got frustrated and dented the aluminum bezel. They dent easily. I had to purchase replacement bezel. Another option is using double stick tape. That is the method most modern trim is attached. I have never used this option but it may be worth a try. Other have used it. Cheers |
![]() |
![]() |
![]() |
#6 |
Senior Member
![]() Join Date: Feb 2022
Location: Ca
Posts: 496
|
Re: Taillight trim
I thought it would be a 15 minute job to snap those clips in and mount the trim. After hours of beating myself up thinking I am an idiot, unable to figure out the clips, I realized that I needed to turn in such a way that the spring arm of the clip required to be bent/compressed in a manner not obvious. It felt as though it was over compressed to a point of bending but they hold exceptionably well. And of course a month later I bang a shovel into one offloading some compost.
|
![]() |
![]() |
![]() |
#7 | |
New Member
![]() Join Date: Aug 2022
Location: Milton TN
Posts: 13
|
Re: Taillight trim
Quote:
I hate the idea of double sided tape. |
|
![]() |
![]() |
![]() |
#8 |
Senior Member
![]() Join Date: Mar 2015
Location: washington
Posts: 2,234
|
Re: Taillight trim
In the past I have had to trim the clips with a Dremel. Better than enlarging the holes. I have done that also, but it didn't work out as well as trimming the clips. With all the work to re-pop the clips you would think they could do it a little closer to the originals. But no joy. It's like, "it looks like a clip, lets go with that."
Cheers. Last edited by Accelo; 02-16-2023 at 12:25 PM. |
![]() |
![]() |
![]() |
Bookmarks |
|
|