|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
01-30-2024, 05:34 PM
|
#1 |
|
Registered User
Join Date: Jan 2021
Location: ft worth texas
Posts: 37
|
63 C10 CNotch CPP (no instructions about Panhard Bar???)
Installing a CNotch kit on my 63C 10. I’m to the point where I’m going to cut out the notch for the C notch but my Panhard bar mounting from the factory is in the way I don’t see any instructions on what to do with the Panhard mounting point. Certainly someone is running into this before. Can you give me some advice?
Last edited by ViatminC10; 01-30-2024 at 05:39 PM. |
|
|
|
01-31-2024, 12:01 PM
|
#2 |
|
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,031
|
Re: 63 C10 CNotch CPP (no instructions about Panhard Bar???)
I would:
Mark the overlapping area w/a sharpie. Drill a 3/8" hole @ the inside corner of the 90° area you need to trim. Cut each side to the drilled hole & clean up the edges. The drilled hole @ the 90° section will prevent any cracking @ the notch.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
|
|
|
02-01-2024, 08:09 AM
|
#3 |
|
Registered User
Join Date: Jan 2021
Location: ft worth texas
Posts: 37
|
Re: 63 C10 CNotch CPP (no instructions about Panhard Bar???)
I ended up removing all 5 rivets that hold the pan hard bar mount to frame, removing the mount, trimming the C notch to clear, red rolling pan hard mounting holes. Plan on adding some weld beads when finished.
Hopefully this helps someone else. |
|
|
|
|
02-01-2024, 11:35 AM
|
#4 |
|
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,031
|
Re: 63 C10 CNotch CPP (no instructions about Panhard Bar???)
There 'ya go.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
|
|
|
|
02-01-2024, 02:06 PM
|
#5 |
|
Registered User
Join Date: Jan 2021
Location: ft worth texas
Posts: 37
|
Re: 63 C10 CNotch CPP (no instructions about Panhard Bar???)
Took the shocks loose and jacked up the rear differential to see how the travel would be after the installation.
Here’s a couple pictures ( not sure why they come in rotated?) l |
|
|
|
|
02-02-2024, 02:37 PM
|
#6 |
|
Registered User
Join Date: Jan 2021
Location: ft worth texas
Posts: 37
|
Re: 63 C10 CNotch CPP (no instructions about Panhard Bar???)
Anyone use these shock relocator kits from eBay? They look to be the same as all the other ones that are around 70 bucks.
https://www.ebay.com/itm/323631665854 |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
