The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board > 67-72 Chevrolet & GMC Pickups Projects and Builds

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 05-17-2024, 04:07 PM   #1
LockDoc
The Older Generation


 
LockDoc's Avatar
 
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,373
Re: LockDoc's "Low Budget", "Low Maintenance" Project Thread

Quote:
Originally Posted by Getter-Done View Post
The 4:10 will be a nice addition.

I am guessing 2200 RPM at 70MPH.

Thanks, I hope so.
.
__________________
Leon

Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles

(My Dually Pickup Project Thread)

http://67-72chevytrucks.com/vboard/s...d.php?t=829820

-
LockDoc is offline   Reply With Quote
Old 06-01-2024, 11:30 PM   #2
LockDoc
The Older Generation


 
LockDoc's Avatar
 
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,373
Re: LockDoc's "Low Budget", "Low Maintenance" Project Thread

-
I've been working on the replacement 4.10 center section for the rear end. I not only had to replace the pinion seal but I also had to install a pinion seal repair sleeve. I could tell when I looked at it that the seal was going to need replaced. The yoke had a pretty good groove in it when I disassembled it. I filled it with JB Weld and installed the repair sleeve while the epoxy was still wet.

I only had to pull the axles out far enough to clear the center section when I removed it..

I had to figure out how to get the center section up in the air far enough to get the transmission jack under it so I put a piece of steel pipe across two of the frame cross members and put a rachet strap over the pipe and around the bottom of the center section. I just tightened the rachet strap up until the center section was high enough to get the jack under it. I cut the heads off of 2 bolts and screwed them into the housing to use as guide pins to locate the center section. (you can see one of them in the 8th picture) When I got it high enough I just slid it onto the pins and put the bolts in. Before I slid it all the way back I put some "Right Stuff" sealant on the gasket.

The rest of the pictures are the gasket, and specs on the gasket, seal, and repair sleeve.
Attached Images
     
__________________
Leon

Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles

(My Dually Pickup Project Thread)

http://67-72chevytrucks.com/vboard/s...d.php?t=829820

-

Last edited by LockDoc; 06-01-2024 at 11:36 PM.
LockDoc is offline   Reply With Quote
Old 06-01-2024, 11:32 PM   #3
LockDoc
The Older Generation


 
LockDoc's Avatar
 
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,373
Re: LockDoc's "Low Budget", "Low Maintenance" Project Thread

-
Pictures.
Attached Images
     
__________________
Leon

Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles

(My Dually Pickup Project Thread)

http://67-72chevytrucks.com/vboard/s...d.php?t=829820

-
LockDoc is offline   Reply With Quote
Old 06-01-2024, 11:34 PM   #4
LockDoc
The Older Generation


 
LockDoc's Avatar
 
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,373
Re: LockDoc's "Low Budget", "Low Maintenance" Project Thread

-
More pictures.

The pinion seal and pinion repair sleeve were ordered from Rock Auto.
.
Attached Images
  
__________________
Leon

Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles

(My Dually Pickup Project Thread)

http://67-72chevytrucks.com/vboard/s...d.php?t=829820

-

Last edited by LockDoc; 06-01-2024 at 11:43 PM.
LockDoc is offline   Reply With Quote
Old 06-02-2024, 10:22 AM   #5
Getter-Done
Senior Member
 
Getter-Done's Avatar
 
Join Date: Dec 2009
Location: TN.
Posts: 7,869
Re: LockDoc's "Low Budget", "Low Maintenance" Project Thread

Nice work on the Rachet strap lifter device.

30 years ago, you would have done that differently?
__________________
________________________________________________________________________________________
____________________________________________
84 Chevy K-20
63 Impala (my high school car)

http://67-72chevytrucks.com/vboard/s...Crew Cab Build
Getter-Done is offline   Reply With Quote
Old 06-02-2024, 11:59 PM   #6
LockDoc
The Older Generation


 
LockDoc's Avatar
 
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,373
Re: LockDoc's "Low Budget", "Low Maintenance" Project Thread

Quote:
Originally Posted by Getter-Done View Post
Nice work on the Rachet strap lifter device.

30 years ago, you would have done that differently?
You got that right. Now I have to use my brain more and my muscles (that I don't have) less....


I haven't checked my mileage yet but it dropped my RPM to about 2450 RPM @ 60 mph.
__________________
Leon

Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles

(My Dually Pickup Project Thread)

http://67-72chevytrucks.com/vboard/s...d.php?t=829820

-

Last edited by LockDoc; 06-10-2024 at 05:05 PM.
LockDoc is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:53 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com