What did you do with your truck today, Part 3

[nvrdone]

Wow did i get lucky !! I've got a 12 bolt c10 rear axle in my truck. Last week, I started getting a loud grinding noise out of the left rear wheel. When I got home the axle hub was at 219. so I started pulling it apart. found the left axle bearing was missing one roller. Looked inside both axle tubes with a flashlight and magnetic probe. Nothing. One of my friends suggested before we tear it down, I flush it with carb cleaner and see what comes out. Sure enough the missing roller dropped into the housing. So now, we tear it down and replace all the bearings. I feel like I should buy a lottery ticket!!!

[leegreen]

Final install on new 3" exhaust, this time out to rear bumper by way of rear trailing arms.

tacked up


painted and ready to go back


If anyone can cut and weld and is thinking about doing their own exhaust, these universal U bend kits you can get from car parts places or amazon are a good deal.
One kit like this https://www.kmstools.com/universal-d...haust-kit.html has done 3 exhaust systems now and still has some bends left.
Add your muffler of choice, a v-band clamp or two and some hangers and go for it.

[Tempest67]

Originally Posted by leegreen

Final install on new 3" exhaust, this time out to rear bumper by way of rear trailing arms.

tacked up
Attachment 2374878

painted and ready to go back
Attachment 2374879

If anyone can cut and weld and is thinking about doing their own exhaust, these universal U bend kits you can get from car parts places or amazon are a good deal.
One kit like this https://www.kmstools.com/universal-d...haust-kit.html has done 3 exhaust systems now and still has some bends left.
Add your muffler of choice, a v-band clamp or two and some hangers and go for it.

Nice routing that exhaust, from Drivers side to Pass side. and thanks for the tip on the universal pipe kits, as I wasn't sure what to do, but you have convinced me to give it a try. (when the time comes)

[leegreen]

Originally Posted by Tempest67

Nice routing that exhaust, from Drivers side to Pass side. and thanks for the tip on the universal pipe kits, as I wasn't sure what to do, but you have convinced me to give it a try. (when the time comes)

Driver's side has panhard bar in the way and my DS rear fender mounted fuel fill tends to burp gas if you fill it too fast so I really wanted tailpipe on pass side.

If we had not had a half box of 3" bends in the shop I'd probably have gone 2.5" as I was worried about how hard snaking the exhaust through the suspension was going to be. This bend kit has one end of each piece expanded for a slip joint - that makes it a lot easier to have things hanging in place and still be able to adjust angle and length a bit before tacking. This actually went a lot easier than I expected and that duplicates the experience my son had doing a custom exhaust under LS swapped 91 z28 and my experience doing LS Swapped Sonoma. It was easier in all three cases than anticipated.

I do recommend getting some Vband clamps like https://www.amazon.ca/gp/product/B01N9LO3UA/ expensive but worth it to make things easily removable. I'd consider cutting the flange off your headers and welding vband on too. Just do all welding with the bands clamped together.

And good hangers. I actually scrounged rubber hangers and the steel supports from GM trucks at local pickapart for this, the enlarged end of factory style hanger support is much better than just straight rod. I welded the supports onto bar stock as needed to make mounts I could bolt to frame. Pipe was held in position and hanging in a web of bailing wire while I sorted hanger locations out. some tire lube makes getting the rubber hangers on and off a lot easier

[Tempest67]

I saw that panhard bar.


I have started a new project , 1958 Pontiac wagon, https://67-72chevytrucks.com/vboard/...d.php?t=849781, and it has the X frame, so routing duals on that could be a challenge, but I am a long way from doing that, but good to know those kits are easy to work with.

Thanks again for the info, I enjoy seeing your work

[Oldtruckwelder]

Finished up with installing new door skin and adjust gaps on driver side door and spraying epoxy primer before starting body work.