Bought a rough running '04 Suburban - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

57taskforce · 08-30-2024, 05:42 PM

How was the oil pressure??? That’s a massive leak.

**Steeveedee** · 08-30-2024, 06:30 PM

Does that exhaust valve open and close?

**LockDoc** · 08-30-2024, 11:05 PM

Quote:

Originally Posted by 57taskforce

How was the oil pressure??? That’s a massive leak.

Oil pressure was the same as the 8.1 in the black Dually so no problem there....

Quote:

Originally Posted by Getter-Done

Wow.
The pushrod beat up the snap ring.

I am thinking where are the Ears of that snap ring?

It probably won't make it back through they will drop to the bottom.

Is the oil pan Metal?
If so a magnet could be place in a position away from the oil pickup.

I had a few small pieces of metal on the end of the magnet. Oil pan is aluminum.

Quote:

Originally Posted by Steeveedee

Does that exhaust valve open and close?

You know, I haven't tried that yet. I will do that in the morning. Thanks!
.

Tom · 09-06-2024, 01:26 PM

My 02 subruban is the best bang for your buck truck I've ever bought. I only use it for going to the lake or camping, but its perfect. I love it very much.

jjzepplin · 09-06-2024, 04:50 PM

Magnetic oil plug or just glue a magnet on the pan. Once had a rocker shoot right over the adjusting nut and stud. Had a bunch of valve springs break and cause rocker carnage.

**LockDoc** · 09-06-2024, 05:14 PM

Quote:

Originally Posted by Tom

My 02 subruban is the best bang for your buck truck I've ever bought. I only use it for going to the lake or camping, but its perfect. I love it very much.

I have had an '03 for a few years that I use to plow my drive. The problem is that it is so rusty that I can't drive it on the road any more. This one is still good enough to be road worthy.

Quote:

Originally Posted by jjzepplin

Magnetic oil plug or just glue a magnet on the pan. Once had a rocker shoot right over the adjusting nut and stud. Had a bunch of valve springs break and cause rocker carnage.

I have a couple of small rare earth magnets and I thought about sliding one of them through the drain plug hole. I may check at NAPA or O'rielys to see if they have one of the magnetic plugs.

Thanks guys.
.

TATE228 · 09-11-2024, 10:19 AM

So the trick here is going to be to find a penny or something and jb weld it where the pushrod lands then proceed to fill the crack with the jb weld. The next step isnt really necessary but i like to run a zip tie around the whole thing to make it extra strong. Your welcome

**LockDoc** · 09-11-2024, 05:41 PM

Quote:

Originally Posted by TATE228

So the trick here is going to be to find a penny or something and jb weld it where the pushrod lands then proceed to fill the crack with the jb weld. The next step isnt really necessary but i like to run a zip tie around the whole thing to make it extra strong. Your welcome

By golly, I always appreciate a good tip or two to help me get the job done. I think I will use a ball peen hammer and put a little divot in the penny before I glue it in there. That will help center the push rod. I think I also have a couple of EXTRA HEAVY DUTY Zip Ties I can use.

Thanks!

**Boog** · 09-11-2024, 07:57 PM

Be sure to use the black ones though. They say they last longer.

TATE228 · 09-13-2024, 12:26 PM

I have a stash of the "good home depot zip ties" that I save for just these types of jobs. i just don't trust the standard harbor freight ties for the important jobs.

**HO455** · 09-14-2024, 10:29 AM

**LockDoc** · 09-14-2024, 10:32 AM

Quote:

Originally Posted by TATE228

I have a stash of the "good home depot zip ties" that I save for just these types of jobs. i just don't trust the standard harbor freight ties for the important jobs.

I hope they are better than the $1200 exterior door I just bought from them. It sucked....

08-30-2024, 05:42 PM	#26
57taskforce All about them K’s Join Date: Jun 2014 Location: Land of Entrapment Posts: 6,454	Re: Bought a rough running '04 Suburban How was the oil pressure??? That’s a massive leak. __________________ Tyler '57 3100 http://67-72chevytrucks.com/vboard/s...d.php?t=813888 '72 K20 Cheyenne: 5” lift, 35’s, front dana 60 blah blah blah… http://67-72chevytrucks.com/vboard/s...d.php?t=662879 ‘69 K10 SWB: 4” lift 33”s… in a million pieces http://67-72chevytrucks.com/vboard/s...d.php?t=805206 '98 Silverado LT K2500HD ECLB Vortec 454/4l80E: 6" lift 35x12.5x20’s

08-30-2024, 06:30 PM	#27
Steeveedee Who Changed This? Join Date: Jan 2013 Location: Simi Valley, CA Posts: 10,622	Re: Bought a rough running '04 Suburban Does that exhaust valve open and close? __________________ ~Steven '70 Chevy 3/4T Longhorn CST 402/400/3.56 Custom Camper Simi Valley, CA

09-06-2024, 01:26 PM	#29
Tom driving is in my blood Join Date: Dec 1999 Location: Mesa AZ Posts: 5,739	Re: Bought a rough running '04 Suburban My 02 subruban is the best bang for your buck truck I've ever bought. I only use it for going to the lake or camping, but its perfect. I love it very much. __________________ -78 c10 short/step: 388cid, M20, 5/5 drop, lots more. Playtoy and first vehicle. -98 c1500 x-cab: 5.7L, 17" rims, 5/6 drop, flowmaster, helper bags,NBS rear disk brakes. -02 Suburban 4x4: leveled front -CBR600F4i, CBR600RR, CBR1000RR, and standup skis DISCLAIMER: I cant spell for the life of me.

09-06-2024, 04:50 PM	#30
jjzepplin Registered User Join Date: Feb 2012 Location: Ruskin Florida Posts: 4,566	Re: Bought a rough running '04 Suburban Magnetic oil plug or just glue a magnet on the pan. Once had a rocker shoot right over the adjusting nut and stud. Had a bunch of valve springs break and cause rocker carnage. __________________ 70 swb 4x4 406sbc 700r4 203/205 d60/14blt locker yadda yadda http://67-72chevytrucks.com/vboard/s...88#post6935688 Yeller 72 Blazer 2wd conversion project "No Daggum Money" http://67-72chevytrucks.com/vboard/s...d.php?t=550804 LS1-T56 3.73 LSD super budget build Blanco-2014 Sierra SWB https://67-72chevytrucks.com/vboard/...d.php?t=810350

09-11-2024, 10:19 AM	#32
TATE228 Registered User Join Date: Dec 2003 Location: lake forest park, Washington Posts: 265	Re: Bought a rough running '04 Suburban So the trick here is going to be to find a penny or something and jb weld it where the pushrod lands then proceed to fill the crack with the jb weld. The next step isnt really necessary but i like to run a zip tie around the whole thing to make it extra strong. Your welcome __________________ -1971 K20 350/sm465 -2004 1500

09-11-2024, 07:57 PM	#34
Boog laying low Join Date: Mar 2001 Location: Searcy, Ark. USA Posts: 13,461	Re: Bought a rough running '04 Suburban Be sure to use the black ones though. They say they last longer. __________________ Boog 69 Chevy stepside, 358/T350, 4.11 posi, 4.5/4 drop, rallys, poboy driver primer is finer 91 Chevy sportside, Tahoe, Yukon & GMC Crewcab All GM..'nuff said. I stand for the flag and kneel at the cross

09-13-2024, 12:26 PM	#35
TATE228 Registered User Join Date: Dec 2003 Location: lake forest park, Washington Posts: 265	Re: Bought a rough running '04 Suburban I have a stash of the "good home depot zip ties" that I save for just these types of jobs. i just don't trust the standard harbor freight ties for the important jobs. __________________ -1971 K20 350/sm465 -2004 1500

09-14-2024, 10:29 AM	#36
HO455 Post Whore Join Date: Feb 2016 Location: Portland Oregon Posts: 11,302	Re: Bought a rough running '04 Suburban __________________ Thanks to Bob and Jeanie and everyone else at Superior Performance for all their great help. RIP Bob Parks. 1967 Burban (the WMB),1988 S10 Blazer (the Stink10 II),1969 GTO (the Goat), 1970 Javelin, 1952 F2 Ford OHC six 4X4, 29 Model A, 72 Firebird (the DBP Bird). 85 Alfa Romeo If it breaks I didn't want it in the first place The WMB repair thread http://67-72chevytrucks.com/vboard/s...d.php?t=698377



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.