What did you do to your truck today!

[JON70CST]

Installed a Holley electric fuel pump, and installed a new vacuum modulator on my turbo 400 as the last one was allowing tranny fluid to pass through to the vacuum line right to the carb.

[Stringer]

Tightened my steering gear a little. Big difference. Should have done it 6 months ago.

[TX6T7]

Removed heater core/box, removed cowl panel from below windhield, cut out the old 6cylinder exhaust pipe and muffler. Removed tail lights, reverse lights, clutch pedal, door panels, instrument cluster

Also had to grind off some welds. The previous owner installed a sheet of steel that covers the wood bed and he welded it to the front, sides and back of the bed. It was a PITA, but luckily i had enough patience.....and a grinder with 3" cutting wheel.

[profe56]

I did cut a low hump cover the same border as big hump to install it in my truck.
I've a camaro floor shifter but the cable is short with the big hump and with the low hump i'll have about 2 1/2 inches and I expect now will move more smooth and soft.

[project 67 sub]

went to the brothers show and won lowest truck

[GMC69]

Took the truck to cruise night and decided to adjust the timing once again to try and get rid of this damn stumble on low speed driving. Now sitting at 12BTDC and will get my vacuum gauge to adjust the idle mixture this week hopefully.

[mdaven@aol.com]

Finally removed the dash pad for dyeing. Reinstalled the ignition switch. Removed some more PO wiring tangles. Mounted my door panel trim in preparation to mounting the door panels (powdercoated). Will be reinstalling the seat, seatbelts, ashtray, radio blockout. Removing the metal radio mount from under the dash. Probably going to a single, oil pressure only, gauge set-up. Slowly completing the interior. Soon will get back under the hood to correct some more wiring issues, then hit the road.

[FRENCHBLUE72]

mORE BOARDSANDER ACTION TODAY....

[mmmBoost]

Installed pushrods and roller rockers yesterday


Installed intake, carb, and temp installed valve covers

[RagingAsian]

Washed and waxed everything. Powerwashed the undercarriage and engine and bed. Now I drive it and save up for some nefty goodies.

[GMC69]

Bought some new Stainless Steel door sills with the chevy emblem on them to replace the chrome ones in there now that the passenger one is a bit rusty in one corner. Normally I would leave it but this year will be my first car show that I have a vehicle to enter and I want the truck as close to perfect as possible.

Here is a picture I found online of what it looks like.

[Rob H.]

I cut the right rear corner off the bed for a buddy to use on his truck, then took the torch to the bed bolts and took it off the frame, found out there is a serious rust problem, but hey, that's what makes it a project right.

[ChevLoRay]

Took my rear end and driveshaft to be sandblasted and painted.

[FRENCHBLUE72]

More mud....board sander and more mud..... this is getting old..

[oldblue1968chevy]

Went outside this AM to my DD 68 started it backed up a few feet and it died.

Bad ?modulator? (half moon thing in dizzy) luckily I had a spare

[phyllis1224]

i had bought some [URL="http://www.12vcity.com"]car parts, wanted to travelling

[mabel]

I was actually thinking of selling it! And I am looking for a new one too! Anyone here would like to give me any suggestions on what to buy next?

[Jeffs70]

well for the last few days I have been doing body work inside the bed. and on it to get it finished where i am happy enough. I went and laid some paint this week and here is what so far I have come up with. dont mind as some of the paint is still wet but it gives a good look IMO I also will be spraying the center section gloss black in a few days. and dont mind I still have some minor body work to do.

[Tomahawk30]

Starting to dismantle the front clip to replace the drivers side fender and hood. Got the grille, trim, and cowl pulled tonight before it got too dark...

[dukcaln]

adapters/spacers and new draglite wheels and new dunlope tires... finished undercoating

[bellemare_486]

Final prep for paint tailgate and hood. Got drivers' door half way there. Tomorrow paint. The next day 5 years and an unknown amount of hours and money will turn an obsession into reality

[Bull72]

Painted the firewall and inner fenders. Pressure washed it, scrubbed it and sprayed it all black. My buddy has a paint gun, and he had some extra black paint. I just bought a little paint thinner and taped her up... Not exactly a 100% attention to every little detail here, but I didn't want to pay a shop to do it.

Before, during and after pics ...

[Rob H.]

I pulled the cowl panel off getting ready to unbolt the front end. Cut the back bumper off and that later model bumper and push bar off. I removed the front panel from the rusty bed I pulled the other day, it is perfect. I'm gonna have to replace the back half of the frame it's swiss cheese. I did find a donor, just haven't got it yet, price is right trading scrap for scrap! You know what they say one man's junk is another man's treasure!

[bruin_d]

Cleaned up/painted the tranny. Test fit/adjusted the new Lokar shifter so i don't have to do it when its in. Bolted tranny to motor....its going in tomorrow!!!!!

[wwotr]

Bought a Gas Tank Carpet Kit and a Fiber Board Cover.