![]() |
![]() |
#2476 |
Registered User
Join Date: Sep 2014
Location: USA
Posts: 2,249
|
Re: What did you do with your truck today, Part 3
The litany of bad news continues. This was the result when I tried to rope in my barn door glass. I suspect cold weather made the rubber too rigid.
__________________
1951 Chevy Panel Truck Last edited by MiraclePieCo; 12-24-2018 at 05:32 PM. |
![]() |
![]() |
![]() |
#2477 |
Registered User
Join Date: Aug 2016
Location: Hunkered Down
Posts: 1,842
|
Re: What did you do with your truck today, Part 3
Ouch. Sorry about that!
|
![]() |
![]() |
![]() |
#2478 |
Registered User
Join Date: Feb 2016
Location: Othello washington
Posts: 400
|
Re: What did you do with your truck today, Part 3
Dash wireing for the most part complete, guages light up and all looks good so far, some question on ohms for fuel guage and sender, might not talk to each other in the same language. Waiting on a maxi fuse holder to finish the right side of engine wireing, electric choke yet to finish, wire all run to front and back.
|
![]() |
![]() |
![]() |
#2479 |
Registered User
Join Date: Feb 2016
Location: Othello washington
Posts: 400
|
Re: What did you do with your truck today, Part 3
Engine bay
|
![]() |
![]() |
![]() |
#2480 | |
Senior Member
![]() Join Date: May 2007
Location: Doodah Kansas
Posts: 7,773
|
Re: What did you do with your truck today, Part 3
Quote:
use lube, any old lube (except old lube), dish soap, vaseline, even some squirts of windex.
__________________
the mass of men live lives of quiet desperation if there is a problem, I can have it. new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393 |
|
![]() |
![]() |
![]() |
#2481 |
Registered User
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
|
Re: What did you do with your truck today, Part 3
I got the spindles off my axle and sized them up with the other two pair I have, been curious as I didn't remember the other pair I had. So I have two pairs of the passenger car 49-54 and then the ones that were on the axle are different, not sure of the difference but that is for another post.
![]() Brian
__________________
1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings" |
![]() |
![]() |
![]() |
#2482 |
Registered User
Join Date: Mar 2013
Location: albuquerque New Mexico
Posts: 522
|
Re: What did you do with your truck today, Part 3
drove 50 miles to pick up an powerwheels brute 4wheeler for the boy and 50 miles back. ya know just a truck doing truck things.
|
![]() |
![]() |
![]() |
#2483 |
Registered User
Join Date: Dec 2011
Location: Moxee WA
Posts: 1,470
|
Re: What did you do with your truck today, Part 3
brian: its been a few years since I installed passenger car spindles on my original I beam axle. if the grey cells are correct, the passenger car spindle angle between the king pin and the axle stub are different than the pick up ones. that causes a lot of caster and a big bow in the axle if you can bend it enough to get it aligned.
|
![]() |
![]() |
![]() |
#2484 | |
Registered User
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
|
Re: What did you do with your truck today, Part 3
Quote:
Brian
__________________
1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings" |
|
![]() |
![]() |
![]() |
#2485 |
Registered User
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
|
Re: What did you do with your truck today, Part 3
Started going over the front end parts trying to figure out what I have and I will use.
Brian
__________________
1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings" |
![]() |
![]() |
![]() |
#2486 |
Registered User
Join Date: Aug 2014
Location: Vacaville, CA
Posts: 133
|
Re: What did you do with your truck today, Part 3
Been a few days, but drove the beast to work.
![]() |
![]() |
![]() |
![]() |
#2487 |
Registered User
![]() Join Date: Oct 2011
Location: Tucson, AZ
Posts: 639
|
Re: What did you do with your truck today, Part 3
Love the look, nice rig.
__________________
|
![]() |
![]() |
![]() |
#2488 |
Senior Member
![]() Join Date: Mar 2011
Location: West Plains, Missouri
Posts: 7,557
|
Re: What did you do with your truck today, Part 3
Cool, that's why we build them. Looks great...Jim
__________________
my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=459839 Jimbo's long bed step build:http://67-72chevytrucks.com/vboard/s...t=464626<br /> |
![]() |
![]() |
![]() |
#2489 |
Registered User
Join Date: Sep 2014
Location: USA
Posts: 2,249
|
Re: What did you do with your truck today, Part 3
After my barn door window installation debacle I was forced to order some of the expensive rubbers from Steele. They arrived today - OMG what a difference! The standard window seals from most AD parts retailers are hard, inflexible and extremely difficult for a novice like me to install. The Steele units conversely are soft and supple. I anticipate a much easier installation. But at this price I'd better not damage these!
__________________
1951 Chevy Panel Truck |
![]() |
![]() |
![]() |
#2490 |
Registered User
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
|
Re: What did you do with your truck today, Part 3
With Christmas stuff and just being beat I have missed getting out for my five minutes over the last few days. I got out there today and finished up the frame so it is ready for powdercoating. It had a few dents and they are all fixed now. The "cart" thingies I made needed a bit of work too and I got that done. Removed the shackle shafts and put some oil on them so the hole they go in will be protected when sand blasting and powedercoating.
Now, I have to find something to do while I am waiting for the powder coating. One of the things is get all the springs and axle to get it rolling. I have to pull the rear end apart next I am thinking. Brian
__________________
1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings" |
![]() |
![]() |
![]() |
#2491 |
Registered User
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
|
Re: What did you do with your truck today, Part 3
I had a visitor at the house today too, with cmayna (Craig) coming buy to get a little part I had for him. We had a nice chat with his truck and mine, it was a nice bit of the day for sure. He drove his basically original truck (got a later 235 and a stereo LOL) over from across the SF bay and this truck is SOOOOOOO damn cool it's crazy! He posted this photo a while ago.
I thought it was cool seeing it in the photo but in person, wow, it is beyond cool. Thanks Craig for the visit! Brian
__________________
1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings" |
![]() |
![]() |
![]() |
#2492 |
Registered User
![]() Join Date: Oct 2011
Location: Tucson, AZ
Posts: 639
|
Re: What did you do with your truck today, Part 3
Nice, love using the old trucks for work.
__________________
|
![]() |
![]() |
![]() |
#2493 | |
Registered User
Join Date: Jan 2016
Location: Inglewood, CA
Posts: 324
|
Re: What did you do with your truck today, Part 3
Quote:
|
|
![]() |
![]() |
![]() |
#2494 |
Registered User
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
|
Re: What did you do with your truck today, Part 3
I continued a centuries old Christmas Tradition disassembling a rear end with my brother.
Brian
__________________
1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings" |
![]() |
![]() |
![]() |
#2495 |
Registered User
Join Date: Feb 2010
Location: Lebanon, Ohio
Posts: 1,359
|
Re: What did you do with your truck today, Part 3
That's a little weird, Brian, but I hope you had a great time!
__________________
Bob "It won't take long and it won't cost much." '55 3100 (383/700R4)--'55 Belair Sedan (350/4-speed)--'64 'Vette Conv. (327/4-speed)--'68 GTO Conv. (462/4-speed)--'69 Cutlass Conv. (350/TH350)--'06 'Vette Conv. (LS2/6-speed) Bob's Retirement Build - My 55 TF Bob's 700R4 Build (how-to) |
![]() |
![]() |
![]() |
#2496 |
Senior Member
![]() Join Date: Mar 2011
Location: West Plains, Missouri
Posts: 7,557
|
Re: What did you do with your truck today, Part 3
Brian, what's the ratio, and are the axle shafts the good ones???..Jim
__________________
my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=459839 Jimbo's long bed step build:http://67-72chevytrucks.com/vboard/s...t=464626<br /> |
![]() |
![]() |
![]() |
#2497 |
Registered User
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
|
Re: What did you do with your truck today, Part 3
Jim, I ended up finishing the day with food poisoning after lunch. We are talking going to the hospital and all. I am still KNOCKED OUT by it, I will likely be staying home tomorrow when my family goes to my sister-in-law's house for Christmas.
I am really screwed up, hope it's over by tomorrow sometime but I don't see it. Brian
__________________
1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings" |
![]() |
![]() |
![]() |
#2498 | |
Registered User
Join Date: Mar 2013
Location: albuquerque New Mexico
Posts: 522
|
Re: What did you do with your truck today, Part 3
Quote:
|
|
![]() |
![]() |
![]() |
#2499 |
Senior Member
![]() Join Date: Mar 2011
Location: West Plains, Missouri
Posts: 7,557
|
Re: What did you do with your truck today, Part 3
Hey Brian, sorry for the bad food. That's nothing you can fix in a day. Take care...Jim
__________________
my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=459839 Jimbo's long bed step build:http://67-72chevytrucks.com/vboard/s...t=464626<br /> |
![]() |
![]() |
![]() |
#2500 | |
Senior Member
![]() Join Date: Oct 2016
Location: Olympia, WA
Posts: 523
|
Re: What did you do with your truck today, Part 3
Quote:
![]() Brian, get better soon, I had food poisoning once 30+ years ago and I'm still finicky about what I eat. Jim W |
|
![]() |
![]() |
![]() |
Bookmarks |
|
|