What did you do to your truck today part III - Page 101 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Railroadman · 09-29-2016, 08:59 PM

Finished removing the doors from the Stahl utility body on my '66. Tomorrow they go for sandblasting, then the fun starts of fixing/replacing the rusted out areas. This one is not bad but some are a bit worse for the wear.

[IMG]

[/IMG]

lowslow64 · 09-30-2016, 05:46 PM

Sprayed the firewall and frame with Raptor bed liner. Looks great and easy to spray.

RDrancher · 09-30-2016, 08:36 PM

Drug this '64 out from it's resting place for the last 16 years. Amazingly enough, the tires were still aired up! I'll have it home this weekend.

TJ's Chevy · 10-02-2016, 12:18 AM

Bottom of the cab in two coats of rust tough primer for temporary. Tomorrow the epoxy goes on.

forestb · 10-02-2016, 09:44 PM

New seat belts and old seat. She is now ready to drive on the street after over a year.

curvedglass · 10-03-2016, 08:44 AM

reconnected my heater, general de-greasing and crud removal of the block, valve cover and side cover gasket replacement, cleaned up the ignition wires, and polished the air filter cover on the weber.

joesscamaro · 10-03-2016, 09:34 AM

Quote:

Originally Posted by lowslow64

Sprayed the firewall and frame with Raptor bed liner. Looks great and easy to spray.

That Raptor Liner looks good! I read good reviews on their product, but haven't gotten around to spraying the underside of my cab yet...and I've never seen any pictures of it in use.

coyn · 10-03-2016, 06:40 PM

Been getting everything pulled out of the dash and off the firewall. Now to start replacing sheet metal. Lots of work ahead.

Jimal · 10-09-2016, 09:47 PM

https://www.youtube.com/watch?v=b_VGMx2-qoE

Something a little different.

66Submarine · 10-11-2016, 02:18 PM

Quote:

Originally Posted by Jimal

https://www.youtube.com/watch?v=b_VGMx2-qoE

Something a little different.

Why not me??? 50MPH on the straights? I'd have given them a real show!

Neat.

Jimal · 10-11-2016, 05:27 PM

Quote:

Originally Posted by 66Submarine

Why not me??? 50MPH on the straights? I'd have given them a real show!

Neat.

Yeah, the lap didn't include the long front straight, so I didn't have to worry about cooking the brakes in Big Bend. That being said, with the rudimentary safety equipment (old lap belts and not much else) I wasn't motivated to push it.

62 Barnfind · 10-16-2016, 09:32 AM

Got the timing right and tested the overdrive trans to see if it works.

davbowen · 10-16-2016, 11:57 AM

LED lights in my shifter knob

testerdahl · 10-16-2016, 08:37 PM

Finally got time to get the glove box back together with a new insert.

Broke down and pulled off the back bumper. I realized the lights "issue" could likely be replaced with ATV or motorcycle lights. I'm going to work on finding them.

Also, needed the bumper off to pound out a dent in order for the rear driver wheel to have more clearance as well as attempt to get the top bolt off the rear shock. It has been "stubborn" so far.

jb9281 · 10-17-2016, 07:51 AM

Got my bedside stripes and letters hand painted today. Local sign shop painted them for me. They are metallic silver

BEK&TBKinNC · 10-20-2016, 09:27 PM

Not today but Monday, pulled it out of its resting place for the last 9 years and brought home.
Bought it as a non runner, but got it running Wednesday evening.

coyn · 10-23-2016, 07:00 PM

Was finally able to get the cab off to do some rust repair today. I put some new cab supports in also. It's not much but it sure feels good to get some new parts welded in.

62 Barnfind · 10-23-2016, 07:20 PM

Installed the power booster/ hydro clutch today. Still have to run the brake lines and linkage.

shp4man · 10-24-2016, 09:49 AM

Figured out that the aftermarket AM radio that was in the old truck when I got it actually works. It's so old, it was made in Japan, not China.

forestb · 10-24-2016, 12:02 PM

I took the truck out for it's maiden voyage (sense it was painted). I have not driven it for over a year and a half. The doors rattled like crazy but I think that is because the whether stripping is falling off. The inside door handle also fell of but that is not a big deal.

Sorry no pictures.

**idbeast** · 10-27-2016, 11:07 AM

my efforts![IMG]

image hosting free no registration[/IMG]

20mb image hosting

shp4man · 10-27-2016, 12:33 PM

Figured out that Chevy designed the side mount spare to be movable depending on what access was needed to the bed. So I'm putting it back to where the spare fits in the indent on the fender.

Got that old box setup out of the bed. The thing is steel and heavy. Had to use my motorcycle jack to get that crap out of there.

**AngryPirate** · 10-27-2016, 03:02 PM

Quote:

Originally Posted by 62 Barnfind

Got the timing right and tested the overdrive trans to see if it works.

Man, I like that breather you have on there. Do you mind if I ask what it is and where you got it?

Also, it looks like you have a hydraulic clutch set up like my '60 GMC...what part did you use to set up your brakes and clutch?

Thanks!

**The Rocknrod** · 10-27-2016, 03:40 PM

62 Barnfind truck is awesome! Hope he answers where he got those.
I have seen air cleaners "Like" those also, I think Speedway http://www.speedwaymotors.com/Nostal...ner,34533.html
Mooneyes http://www.mooneyesusa.com/product-p/jehe9600c.htm
http://shop.kustomcarparts.com/Chrom...?categoryId=-1
http://shop.kustomcarparts.com/7-1-2...?categoryId=-1
http://shop.kustomcarparts.com/Chrom...?categoryId=-1

n8op · 10-28-2016, 11:44 AM

Trying to get first gear back in.-------------------actually just fixed a bad grease fitting and removed a broke manifold bolt.

09-29-2016, 08:59 PM	#2501
Railroadman Registered User Join Date: Jun 2016 Location: Rochester NY Posts: 108	Re: What did you do to your truck today part III Finished removing the doors from the Stahl utility body on my '66. Tomorrow they go for sandblasting, then the fun starts of fixing/replacing the rusted out areas. This one is not bad but some are a bit worse for the wear. [IMG][/IMG]

09-30-2016, 05:46 PM	#2502
lowslow64 Registered User Join Date: Dec 2009 Location: Rockwall Texas Posts: 79	Re: What did you do to your truck today part III Sprayed the firewall and frame with Raptor bed liner. Looks great and easy to spray. Attached Images

09-30-2016, 08:36 PM	#2503
RDrancher Registered User Join Date: Aug 2014 Location: Decatur, Texas Posts: 673	Re: What did you do to your truck today part III Drug this '64 out from it's resting place for the last 16 years. Amazingly enough, the tires were still aired up! I'll have it home this weekend. Attached Images __________________ Romans 10:9 - The Truth

10-02-2016, 12:18 AM	#2504
TJ's Chevy Registered User Join Date: Mar 2013 Location: Southern Oregon Posts: 10,384	Re: What did you do to your truck today part III Bottom of the cab in two coats of rust tough primer for temporary. Tomorrow the epoxy goes on. Attached Images __________________ 1966 Chevy C10 "Project Two Tone" http://67-72chevytrucks.com/vboard/s...d.php?t=596643 1964 GMC "Crustine" semi-build:http://67-72chevytrucks.com/vboard/s...d.php?t=665056 My youtube channel. Username "Military Chevy": https://www.youtube.com/channel/UC_h...fzpcUXyK_5-uiw

10-02-2016, 09:44 PM	#2505
forestb Registered User Join Date: Jan 2009 Location: Burbank, CA Posts: 3,619	Re: What did you do to your truck today part III New seat belts and old seat. She is now ready to drive on the street after over a year. Attached Images

10-03-2016, 08:44 AM	#2506
curvedglass Registered User Join Date: Apr 2014 Location: Pennsylvania Posts: 186	Re: What did you do to your truck today part III reconnected my heater, general de-greasing and crud removal of the block, valve cover and side cover gasket replacement, cleaned up the ignition wires, and polished the air filter cover on the weber. Attached Images __________________ --Life looks better through a curved windshield--

10-03-2016, 06:40 PM	#2508
coyn Registered User Join Date: Aug 2016 Location: Leesburg, IN Posts: 23	Re: What did you do to your truck today part III Been getting everything pulled out of the dash and off the firewall. Now to start replacing sheet metal. Lots of work ahead.

10-09-2016, 09:47 PM	#2509
Jimal Registered User Join Date: Jun 2014 Location: Connecticut Posts: 521	Re: What did you do to your truck today part III https://www.youtube.com/watch?v=b_VGMx2-qoE Something a little different.

10-16-2016, 09:32 AM	#2512
62 Barnfind Registered User Join Date: Jan 2012 Location: Killeen, Tx Posts: 1,365	Re: What did you do to your truck today part III Got the timing right and tested the overdrive trans to see if it works. __________________ John Z 1962 Chevy C10 Stepside 62 Barnfind My build tread: http://67-72chevytrucks.com/vboard/s...d.php?t=507513

10-16-2016, 11:57 AM	#2513
davbowen Registered User Join Date: Jul 2013 Location: grand blanc.mi. Posts: 175	Re: What did you do to your truck today part III LED lights in my shifter knob Attached Images

10-16-2016, 08:37 PM	#2514
testerdahl Registered User Join Date: Apr 2016 Location: Gering Posts: 112	Re: What did you do to your truck today part III Finally got time to get the glove box back together with a new insert. Broke down and pulled off the back bumper. I realized the lights "issue" could likely be replaced with ATV or motorcycle lights. I'm going to work on finding them. Also, needed the bumper off to pound out a dent in order for the rear driver wheel to have more clearance as well as attempt to get the top bolt off the rear shock. It has been "stubborn" so far. Attached Images

10-17-2016, 07:51 AM	#2515
jb9281 Registered User Join Date: Nov 2012 Location: fremont. nc Posts: 272	Re: What did you do to your truck today part III Got my bedside stripes and letters hand painted today. Local sign shop painted them for me. They are metallic silver Attached Images

10-20-2016, 09:27 PM	#2516
BEK&TBKinNC Registered User Join Date: Oct 2013 Location: Oxford, NC Posts: 11	Re: What did you do to your truck today part III Not today but Monday, pulled it out of its resting place for the last 9 years and brought home. Bought it as a non runner, but got it running Wednesday evening. Attached Images __________________ Brian and Tina 1972 Chevy C10 Bella (sold) 1990 Suburban 4x4 B1GNA$TY (sold) 2008 GMC Sierra Crew 4wd dd 1965 C10 (Bervin)

10-23-2016, 07:00 PM	#2517
coyn Registered User Join Date: Aug 2016 Location: Leesburg, IN Posts: 23	Re: What did you do to your truck today part III Was finally able to get the cab off to do some rust repair today. I put some new cab supports in also. It's not much but it sure feels good to get some new parts welded in.

10-23-2016, 07:20 PM	#2518
62 Barnfind Registered User Join Date: Jan 2012 Location: Killeen, Tx Posts: 1,365	Re: What did you do to your truck today part III Installed the power booster/ hydro clutch today. Still have to run the brake lines and linkage. __________________ John Z 1962 Chevy C10 Stepside 62 Barnfind My build tread: http://67-72chevytrucks.com/vboard/s...d.php?t=507513



Register or Log In To remove these advertisements.

10-24-2016, 09:49 AM	#2519
shp4man Registered User Join Date: Oct 2016 Location: San Diego, CA Posts: 556	Re: What did you do to your truck today part III Figured out that the aftermarket AM radio that was in the old truck when I got it actually works. It's so old, it was made in Japan, not China.

10-24-2016, 12:02 PM	#2520
forestb Registered User Join Date: Jan 2009 Location: Burbank, CA Posts: 3,619	Re: What did you do to your truck today part III I took the truck out for it's maiden voyage (sense it was painted). I have not driven it for over a year and a half. The doors rattled like crazy but I think that is because the whether stripping is falling off. The inside door handle also fell of but that is not a big deal. Sorry no pictures.

10-27-2016, 11:07 AM	#2521
idbeast Senior Member Join Date: Oct 2016 Location: Olympia, WA Posts: 523	Re: What did you do to your truck today part III my efforts![IMG]image hosting free no registration[/IMG] 20mb image hosting

10-27-2016, 12:33 PM	#2522
shp4man Registered User Join Date: Oct 2016 Location: San Diego, CA Posts: 556	Re: What did you do to your truck today part III Figured out that Chevy designed the side mount spare to be movable depending on what access was needed to the bed. So I'm putting it back to where the spare fits in the indent on the fender. Got that old box setup out of the bed. The thing is steel and heavy. Had to use my motorcycle jack to get that crap out of there.

10-27-2016, 03:40 PM	#2524
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: What did you do to your truck today part III 62 Barnfind truck is awesome! Hope he answers where he got those. I have seen air cleaners "Like" those also, I think Speedway http://www.speedwaymotors.com/Nostal...ner,34533.html Mooneyes http://www.mooneyesusa.com/product-p/jehe9600c.htm http://shop.kustomcarparts.com/Chrom...?categoryId=-1 http://shop.kustomcarparts.com/7-1-2...?categoryId=-1 http://shop.kustomcarparts.com/Chrom...?categoryId=-1 __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

10-28-2016, 11:44 AM	#2525
n8op Registered User Join Date: Sep 2016 Location: Huntington WV Posts: 15	Re: What did you do to your truck today part III Trying to get first gear back in.-------------------actually just fixed a bad grease fitting and removed a broke manifold bolt. Attached Images

Register or Log In To remove these advertisements.