What did you do with your truck today, Part 3 - Page 103 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

svr · 01-03-2019, 11:56 PM

Took a little more than 5 min but progress

MARTINSR · 01-04-2019, 02:00 AM

Right on!

Me, did my five minutes, did a little work on my heater, ground down a little spot on it and dug out the wire so tomorrow night I can rewire the motor.

Then I am totally jazzed about this, on my evening walk I went to the local hardware store and found the PERFECT wire to put on the front of the heater! The cool part is I measured it then came home and it was perfect, right on. It's smaller version of the screen I will be putting over the head lamps from a 53 Corvette.

Brian

mikebte · 01-04-2019, 11:20 AM

Quote:

Originally Posted by svr

Took a little more than 5 min but progress

Very nice, That can be time consuming but well worth it in the end. That stuff is as satisfying as popping bubble wrap once its applied.

mikebte · 01-04-2019, 11:22 AM

Quote:

Originally Posted by MiraclePieCo

I continued disassembly of the top of my motor. Last time I did this my back was hurting for a week from working bent over the fender so much. This time I'm limiting myself to an hour or two a day to avoid a repeat. Today I got the alternator and fan off and pulled the distributor. Tomorrow I'll have to go underneath to remove my freshly installed exhaust :-(

Didn't you literally just remove the head to remove a broken pipe plug? At least it seem like it was just yesterday?

Janky59 · 01-04-2019, 04:11 PM

I finished up the installation of a set of Williams split manifolds, cleaned up and painted things while they were apart, on to the exhaust shop tomorrow.

Black_Sheep · 01-05-2019, 05:27 PM

Mid 40’s in early January is almost unheard of in Minnesota. I pulled the cover off the ‘58 and fired it up to run it up to temp. There is too much salt on the roads to drive it, so this will have to do for now...

https://www.facebook.com/mark.wells....6005650103573/

Black_Sheep · 01-05-2019, 05:33 PM

Quote:

Originally Posted by svr

Took a little more than 5 min but progress

Well worth the effort though, looks real good...

DBS5Window · 01-05-2019, 06:15 PM

I finished installing a TCI rear leaf spring kit and a reman Explorer 8.8 rear. Next up brake lines and relocating the fuel tank. I have a Mustang fuel tank from Tanks Inc.

Trucknut57 · 01-05-2019, 06:49 PM

I took it out of the garage and let it soak up some sunshine

.

It really needs a bath

MiraclePieCo · 01-05-2019, 09:33 PM

Got my exhaust removed today to facilitate head removal. I'm plugging away at this only an hour or two a day to save stress on my back. Plus I'm not real enthused about taking the truck apart; building them is rewarding, UN-building them not so much.

MARTINSR · 01-05-2019, 10:21 PM

Yeah, it sucks, but in a little while you will be back on the road! WHOOO HOOOOO!

Brian

evilokc · 01-06-2019, 12:55 AM

took a short drive in the beautiful sunny 60 degree weather today. life is sometimes remarkable. 2 days ago it was snow and ice.

BAM55 · 01-07-2019, 01:30 PM

Well I was able to get get her down on all 4's for the first time since I painted the cab and front clip.

MiraclePieCo · 01-07-2019, 10:25 PM

Quote:

Originally Posted by BAM55

Well I was able to get get her down on all 4's for the first time since I painted the cab and front clip.

I love those little victories, they're so rewarding. Looks like you nailed it!

MiraclePieCo · 01-07-2019, 10:33 PM

The latest in my ongoing, perpetual, unending, eternal head plug saga:

Got the head into a machine shop today. A magnaflux revealed three 1-inch cracks radiating from the threaded temp sender hole. It can't be repaired; replacement is the only option. So far everything to do with this head plug debacle has ended up as worst-case scenario :-( Moral: never remove the factory sender bung.

dsraven · 01-07-2019, 11:46 PM

sorry to hear the head is toast. the good thing is now you know and can move on. weird that there were cracks like that unless someone over-torqued a plug at some point. anyway, its apart now and you know what the deal is, just a matter of getting a new head just like the old one.

nvrdone · 01-08-2019, 12:13 AM

don't get a head just like the old one - you don't want cracks in the replacement !!

MARTINSR · 01-08-2019, 01:55 AM

My five minutes was spent cutting my rear springs apart and hauling them into the garage, no kidding, this took five minutes! HOLY COW I hate to think of the mail guy or gal who had to haul those babies up tot he porch!

I then spent about three hours, no kidding, THREE HOURS boxing up some rocker mouldings I sold on ebay. What will they get it, ONE of my spring shackles! LOLOL

Brian

MiraclePieCo · 01-08-2019, 05:05 AM

Quote:

Originally Posted by dsraven

weird that there were cracks like that unless someone over-torqued a plug at some point.

You may remember the extreme difficulty I had removing that plug, so yeah, I suspect someone over-tightened it, or maybe the removal process caused excessive stress.

Quote:

Originally Posted by nvrdone

don't get a head just like the old one - you don't want cracks in the replacement !!

Since I'm only replacing one head I'll probably have to get one just like the old one.

DransportGarage · 01-08-2019, 10:25 AM

Quote:

Originally Posted by MiraclePieCo

You may remember the extreme difficulty I had removing that plug, so yeah, I suspect someone over-tightened it, or maybe the removal process caused excessive stress.

Since I'm only replacing one head I'll probably have to get one just like the old one.

So, which head do you need? (You can thank me for asking later when one shows up from the forum!)

cmayna · 01-10-2019, 12:44 PM

https://youtu.be/fYA7CQYeIpU

The green turd earning it's keep, picking up some more tan bark for the yard.

MiraclePieCo · 01-10-2019, 05:13 PM

Quote:

Originally Posted by cmayna

https://youtu.be/fYA7CQYeIpU

The green turd earning it's keep, picking up some more tan bark for the yard.

Pretty deft loader operator too.

DransportGarage · 01-10-2019, 10:05 PM

A while back I got a "good deal" on a used Corvette steering wheel. (Brings up an old quote, "One more good deal and we're out of business.") Underneath the leather cover, the top of the wheel that was most exposed to the sun had turned to mush. I cut out the mushy part of the foam core, then replaced that with a split piece of garden hose. I filled the hose with Great Stuff foam. Then I used pieces of fiberglass drywall tape coated with adhesive to build up the contour so that it matched original good foam. I then wrapped the whole mess with 1/2" strips of fiberglass drywall tape, like applying a cast for a broken bone. I think it's going to be fine, if I can hand-stitch a cover...

MiraclePieCo · 01-11-2019, 01:32 AM

Quote:

Originally Posted by DransportGarage

A while back I got a "good deal" on a used Corvette steering wheel. (Brings up an old quote, "One more good deal and we're out of business.") Underneath the leather cover, the top of the wheel that was most exposed to the sun had turned to mush. I cut out the mushy part of the foam core, then replaced that with a split a piece of garden hose. I filled the hose with Great Stuff foam. Then I used pieces of fiberglass drywall tape coated with adhesive to build up the contour so that it matched original good foam. I then wrapped the whole mess with 1/2" strips of fiberglass drywall tape, like applying a cast for a broken bone. I think it's going to be fine, if I can hand-stitch a cover...

I can't wait to see how this comes out.

DransportGarage · 01-11-2019, 02:24 AM

Quote:

Originally Posted by MiraclePieCo

I can't wait to see how this comes out.

Me too.

01-03-2019, 11:56 PM	#2551
svr Registered User Join Date: Feb 2016 Location: Othello washington Posts: 400	Re: What did you do with your truck today, Part 3 Took a little more than 5 min but progress Attached Images __________________ 57 short box, 235, T5, C4 http://67-72chevytrucks.com/vboard/s...d.php?t=739132

01-04-2019, 02:00 AM	#2552
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: What did you do with your truck today, Part 3 Right on! Me, did my five minutes, did a little work on my heater, ground down a little spot on it and dug out the wire so tomorrow night I can rewire the motor. Then I am totally jazzed about this, on my evening walk I went to the local hardware store and found the PERFECT wire to put on the front of the heater! The cool part is I measured it then came home and it was perfect, right on. It's smaller version of the screen I will be putting over the head lamps from a 53 Corvette. Brian __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

01-04-2019, 04:11 PM	#2555
Janky59 Registered User Join Date: Feb 2015 Location: Salisbury, MD Posts: 91	Re: What did you do with your truck today, Part 3 I finished up the installation of a set of Williams split manifolds, cleaned up and painted things while they were apart, on to the exhaust shop tomorrow. Attached Images __________________ 2018 BMW R1200RT 2013 Aprilia Tuono 2012 Ford Flex 2011 Ducati Hypermotard 1959 Chevy 3100

01-05-2019, 05:27 PM	#2556
Black_Sheep Registered User Join Date: Jun 2017 Location: upper midwest Posts: 1,129	Re: What did you do with your truck today, Part 3 Mid 40’s in early January is almost unheard of in Minnesota. I pulled the cover off the ‘58 and fired it up to run it up to temp. There is too much salt on the roads to drive it, so this will have to do for now... https://www.facebook.com/mark.wells....6005650103573/ __________________ Mark Brother's keeper - '58 Stepside build

01-05-2019, 06:15 PM	#2558
DBS5Window Registered User Join Date: Oct 2016 Location: Byrnes Mill, Mo Posts: 1	Re: What did you do with your truck today, Part 3 I finished installing a TCI rear leaf spring kit and a reman Explorer 8.8 rear. Next up brake lines and relocating the fuel tank. I have a Mustang fuel tank from Tanks Inc.

01-05-2019, 06:49 PM	#2559
Trucknut57 Registered User Join Date: Aug 2010 Location: Jennings, OK Posts: 322	Re: What did you do with your truck today, Part 3 I took it out of the garage and let it soak up some sunshine . It really needs a bath Attached Images __________________ Somehow, the idiots survive despite their best efforts to kill themselves. - dcozzi

01-05-2019, 09:33 PM	#2560
MiraclePieCo Registered User Join Date: Sep 2014 Location: USA Posts: 2,249	Re: What did you do with your truck today, Part 3 Got my exhaust removed today to facilitate head removal. I'm plugging away at this only an hour or two a day to save stress on my back. Plus I'm not real enthused about taking the truck apart; building them is rewarding, UN-building them not so much. __________________ 1951 Chevy Panel Truck

01-05-2019, 10:21 PM	#2561
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: What did you do with your truck today, Part 3 Yeah, it sucks, but in a little while you will be back on the road! WHOOO HOOOOO! Brian __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

01-06-2019, 12:55 AM	#2562
evilokc Registered User Join Date: Mar 2013 Location: albuquerque New Mexico Posts: 522	Re: What did you do with your truck today, Part 3 took a short drive in the beautiful sunny 60 degree weather today. life is sometimes remarkable. 2 days ago it was snow and ice.

01-07-2019, 01:30 PM	#2563
BAM55 Registered User Join Date: Jan 2016 Location: Inglewood, CA Posts: 324	Re: What did you do with your truck today, Part 3 Well I was able to get get her down on all 4's for the first time since I painted the cab and front clip. __________________ BAM 55/58 Chevy Truck Project Fixing a mess of a clip installation

01-07-2019, 10:33 PM	#2565
MiraclePieCo Registered User Join Date: Sep 2014 Location: USA Posts: 2,249	Re: What did you do with your truck today, Part 3 The latest in my ongoing, perpetual, unending, eternal head plug saga: Got the head into a machine shop today. A magnaflux revealed three 1-inch cracks radiating from the threaded temp sender hole. It can't be repaired; replacement is the only option. So far everything to do with this head plug debacle has ended up as worst-case scenario :-( Moral: never remove the factory sender bung. __________________ 1951 Chevy Panel Truck

01-07-2019, 11:46 PM	#2566
dsraven Registered User Join Date: Nov 2010 Location: calgary alberta Posts: 8,218	Re: What did you do with your truck today, Part 3 sorry to hear the head is toast. the good thing is now you know and can move on. weird that there were cracks like that unless someone over-torqued a plug at some point. anyway, its apart now and you know what the deal is, just a matter of getting a new head just like the old one.

01-08-2019, 12:13 AM	#2567
nvrdone Registered User Join Date: Dec 2011 Location: Moxee WA Posts: 1,479	Re: What did you do with your truck today, Part 3 don't get a head just like the old one - you don't want cracks in the replacement !!

01-08-2019, 01:55 AM	#2568
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: What did you do with your truck today, Part 3 My five minutes was spent cutting my rear springs apart and hauling them into the garage, no kidding, this took five minutes! HOLY COW I hate to think of the mail guy or gal who had to haul those babies up tot he porch! I then spent about three hours, no kidding, THREE HOURS boxing up some rocker mouldings I sold on ebay. What will they get it, ONE of my spring shackles! LOLOL Brian Attached Images __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

01-10-2019, 12:44 PM	#2571
cmayna Registered User Join Date: Oct 2018 Location: Menlo Park, CA Posts: 90	Re: What did you do with your truck today, Part 3 https://youtu.be/fYA7CQYeIpU The green turd earning it's keep, picking up some more tan bark for the yard. __________________ Craig My truck '50 Chevy 3100-5 window If I'm not working on my truck, I'm fishing with the wife or smoking Salmon.



Register or Log In To remove these advertisements.

01-10-2019, 10:05 PM	#2573
DransportGarage Registered User Join Date: Feb 2010 Location: Lebanon, Ohio Posts: 1,359	Re: What did you do with your truck today, Part 3 A while back I got a "good deal" on a used Corvette steering wheel. (Brings up an old quote, "One more good deal and we're out of business.") Underneath the leather cover, the top of the wheel that was most exposed to the sun had turned to mush. I cut out the mushy part of the foam core, then replaced that with a split piece of garden hose. I filled the hose with Great Stuff foam. Then I used pieces of fiberglass drywall tape coated with adhesive to build up the contour so that it matched original good foam. I then wrapped the whole mess with 1/2" strips of fiberglass drywall tape, like applying a cast for a broken bone. I think it's going to be fine, if I can hand-stitch a cover... Attached Images __________________ Bob "It won't take long and it won't cost much." '55 3100 (383/700R4)--'55 Belair Sedan (350/4-speed)--'64 'Vette Conv. (327/4-speed)--'68 GTO Conv. (462/4-speed)--'69 Cutlass Conv. (350/TH350)--'06 'Vette Conv. (LS2/6-speed) Bob's Retirement Build - My 55 TF Bob's 700R4 Build (how-to) Last edited by DransportGarage; 01-11-2019 at 02:23 AM.

Register or Log In To remove these advertisements.