What did you do with your truck today, Part 3 - Page 112 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

MARTINSR · 02-24-2019, 11:00 PM

Put my five minutes in on something I didn't think I had to do and it sucks. Out of the blue this morning something hit me on my rear axle. The spring pads were about a half inch closer together than they are suppose to be. I had ignored it thinking that it won't make a difference moving the spring a quarter inch in on each side, that's close enough I figured. Well, what hit me was, what is one side is where it belongs and the other side is off the whole half inch, or what if one side is even in further than that, I hadn't measure to the end of the axle to see if they were at the correct distance from the end. So sure enough, one side was in a half inch, CRAP. So I figured I would cut that one off and then leave the other. Well, then I got to looking at the angle the rear end would be at where they were mounted, it was WAY off with the third member pointing up! Geeeez, I cut them both off and will clamp it all together until I have the engine tranny and height where I want it then get the pinion angle right and weld them on.

I mean, come on, that's the right way to do it. I was just dreaming that the last guy had welded the perches on there right. One thing that was real nice, the dudes welds sucked so they was easy to remove.

Brian

MiraclePieCo · 02-25-2019, 03:12 AM

Quote:

Originally Posted by evilokc

today I finally got my hood installed.

I'm used to seeing your truck with no hood; I probably won't recognize it now ;-)

MARTINSR · 02-26-2019, 02:03 AM

My five minutes got me repairing the rear end housing where the perches were. So I got something done on the truck.
Then I got a piece made for the trunk floor of my brothers '39. His is rusted, he bought this patch from a guy and it's only a little less rusted than his!

So I used it as a pattern and made a patch for him.

Brian

MiraclePieCo · 02-26-2019, 06:01 PM

This is ridiculous. Snow has been on the ground for a full month here now. I've never seen that in my six decades living here. Since my garage is filled with the typical homeowner stuff - bicycles, lawnmowers, kayaks, etc - I usually move my panel truck into the driveway to work. Not possible for a month and no end in sight in the long range forecast. Snowing again now, and an entire county north of me without electricity for a week. Tried to eat at a local restaurant but they were closed because they couldn't get food through on the highways for a couple of days. So alas my truck languishes in the garage and I sit on my butt day after day waiting for Spring.

Anyone else old enough to remember what scientists were predicting in the 1960s-70s? Looks like they were right!

DransportGarage · 02-26-2019, 10:08 PM

Quote:

Originally Posted by MiraclePieCo

This is ridiculous. Snow has been on the ground for a full month here now. I've never seen that in my six decades living here. Since my garage is filled with the typical homeowner stuff - bicycles, lawnmowers, kayaks, etc - I usually move my panel truck into the driveway to work. Not possible for a month and no end in sight in the long range forecast. Snowing again now, and an entire county north of me without electricity for a week. Tried to eat at a local restaurant but they were closed because they couldn't get food through on the highways for a couple of days. So alas my truck languishes in the garage and I sit on my butt day after day waiting for Spring.

Anyone else old enough to remember what scientists were predicting in the 1960s-70s? Looks like they were right!

I hope you're not serious. If so, read about the 1922 "Climate Change".

https://www.snopes.com/fact-check/warm-welcome/

Weather is cyclic. There is change going on, but it's nothing the supposed climate change "experts" have got a handle on. Predicting stuff, however, does make them feel important and sometimes even gets them a paycheck.

**mr48chev** · 02-26-2019, 10:17 PM

Not a whole lot of progress going on around here unless you count snow shoveled paths.

I did almost get out the the 51 1-1/2 ton though.

**mr48chev** · 02-26-2019, 10:34 PM

We didn't have enough snow to talk about all winter until February. I ran around outside in flanel shirts and no jacket a lot in Janurary and was getting stuff move aound so I could work on my shop and in February we have Had around 2 ft total snow in three weeks.

We are supposed to get the tail end of the storm that Mirical Pie Co is gettng sometime in the next 24 and so far I haven't had to shovel the whole 400 ft but am afraid that the time is coming.

MARTINSR · 02-26-2019, 10:35 PM

WOW!

Brian

MARTINSR · 02-27-2019, 12:03 AM

My five minutes today was bringing my axle and steering goodies to the UPS store shipping it off to SIDS to be dropped and all the steering linkage modified, WHOOOO HOOOOO!

Brian

DransportGarage · 02-27-2019, 03:25 AM

Sorry to see all the snow, guys! We've been lucky here in SW Ohio for the last several years. The plow was out once this year, and not at all last year (or was it the year before?). Conversely, in 2002 we got 14" the day after Christmas, and it was 25 below in 1977, when people were walking across the Ohio river:

https://www.youtube.com/watch?v=3rXnNJhnfeo

Dyslexic Dog · 02-27-2019, 09:10 AM

Sorry for the thread drift but I always like to engage the deniers. Rate of change. X squared. The peaks and valleys have not changed as much as the frequency. Weather is different then climate. Scientist theory is a theory that you test the data with. Guess what? Lots and lots and lots and lots of data support it. Of course you could always just believe a political oped piece instead.

DransportGarage · 02-27-2019, 10:32 AM

Quote:

Originally Posted by Dyslexic Dog

Sorry for the thread drift but I always like to engage the deniers. Rate of change. X squared. The peaks and valleys have not changed as much as the frequency. Weather is different then climate. Scientist theory is a theory that you test the data with. Guess what? Lots and lots and lots and lots of data support it. Of course you could always just believe a political oped piece instead.

...figures lie and liars figure... Read the 1922 "facts" again.

(OK. Dyslexic Dog is right, I'm off topic. My fault. You guys can take a few more shots, but I'll shut up.)

Kevin Mac · 02-28-2019, 09:53 AM

I'm still changing my mind on my hydroboost install. I just wasn't comfortable with reservoir on firewall so I made another adapter plate to slant the HB and bough a new reservoir without as much angle. It will fit under floor with couple inches to spare. I will have to fill with syringe but figured how often do you have to add fluid.
I don't know how you guys build from ground up, it would take me 10 years with changing my mind all the time. If anybody wants my 1/4" aluminum adapter plate and aluminum master cylinder push in adapters I made pay shipping and they are yours. The push in adapters have 1/8" pipe thread.
Mac

DransportGarage · 02-28-2019, 10:06 AM

Quote:

Originally Posted by Kevin Mac

I'm still changing my mind on my hydroboost install. I just wasn't comfortable with reservoir on firewall so I made another adapter plate to slant the HB and bough a new reservoir without as much angle. It will fit under floor with couple inches to spare. I will have to fill with syringe but figured how often do you have to add fluid.
I don't know how you guys build from ground up, it would take me 10 years with changing my mind all the time. If anybody wants my 1/4" aluminum adapter plate and aluminum master cylinder push in adapters I made pay shipping and they are yours. The push in adapters have 1/8" pipe thread.
Mac

VERY nice engineering!

MARTINSR · 02-28-2019, 10:56 AM

Yep, good stuff Mac!

Brian

MARTINSR · 03-01-2019, 01:44 AM

I got the heater motor rewired tonight. I would like to get the whole thing restored and waiting for installation, we well see. I need to have the core pressure tested, I'll see if I can get that done tomorrow.

Brian

MiraclePieCo · 03-01-2019, 05:15 PM

Still snowbound here, big snow boulders pushed up by the plows across my driveway, so work on truck is5 limited. Electricity was out and no internet for 3 days. Using my phone to post this message. You may have heard about the Amtrak passengers stranded for days when their train became stuck in th snow near here. The only thing I've done on the truck is install my inside rear view mirror - whoopee!

Edit: Just found this: the Governor has declared a State of Emergency for my county:

Oregon Governor Kate Brown Declares State of Emergency in 10 Counties Hit by Winter Storms
Oregon Governor Kate Brown has declared a state of emergency in ten counties because of severe winter storm conditions. Brown made the declaration Thursday for counties including Coos, Curry, Deschutes, Douglas, Jackson, Josephine, Klamath, Lane, Linn, and Marion. In a news release, Brown said the declaration will provide additional resources and the potential for federal highway system money for road fixes. The Oregon Office of Emergency Management will coordinate state resources from police to transportation workers to the National Guard to support local communities as needed. The resources will help communities recover from heavy snow and ice accumulation, high winds, flooding, and landslides. The state of emergency will last 30 days unless Brown ends it before then. In this region, Douglas County has been the hardest-hit area. The Douglas County Board of Commissioners and Douglas County Sheriff's Office have received many requests from people who want to help.

DransportGarage · 03-01-2019, 09:24 PM

My five minutes (well, two hours.). I'm trying to figure out how to do a pocket for my sun visors and flames in my headliner. This is just a piece of cardboard and some scrap high density 1/4" foam and vinyl. I got incomplete distribution of glue because it was too thick, which caused bubbles in the vinyl, but I think I can do this if I throw this Harbor Fright gun away, pull out another one, and open a new can of Landau contact cement.

**idbeast** · 03-01-2019, 10:33 PM

Well my 5 minutes was more like 7 hours of wet sanding everything except for the cab and bed cover, then loading it all up and taking it to the body shop for paint!

MARTINSR · 03-02-2019, 01:40 AM

My five minutes didn't do a damn thing ON the truck darn it, boxed up some stuff I sold on eBay to buy stuff for the truck though.

Brian

**mr48chev** · 03-02-2019, 02:07 AM

Bought 245 bucks worth of firewood to keep the house warm. I did look up some parts for the truck while waiting for the wood to be delivered. Now I need to finish splitting my mom's wood and bring the splitter home and do mine.

With all the snow on the ground I can't do much on the shop or the truck.

mick53 · 03-02-2019, 08:27 PM

I took the king pins out of a 53 1/2 ton axle to give the spindles to a forum member. It's been a while since I did this and forgot what a pain it is. 20 ton press and torch. When they finally let lose they were hot and angry.

MARTINSR · 03-02-2019, 08:49 PM

I am beat, don't know why but I am beat. I got out there and did some little crap. I am actually pleased with what I got done, a little on my heater, got up in the attic and some things inventoried, I got something done just not much for a whole day.

Brian

DransportGarage · 03-02-2019, 09:32 PM

Cut the foam for the headliner flames...

Dongray · 03-02-2019, 09:42 PM

Quote:

Originally Posted by MARTINSR

My five minutes today was bringing my axle and steering goodies to the UPS store shipping it off to SIDS to be dropped and all the steering linkage modified, WHOOOO HOOOOO!

Brian

Hey way to go! My sids front end looks pretty sweet with the drop and There were no issues with dealing with Sid or assembling.

02-24-2019, 11:00 PM	#2776
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: What did you do with your truck today, Part 3 Put my five minutes in on something I didn't think I had to do and it sucks. Out of the blue this morning something hit me on my rear axle. The spring pads were about a half inch closer together than they are suppose to be. I had ignored it thinking that it won't make a difference moving the spring a quarter inch in on each side, that's close enough I figured. Well, what hit me was, what is one side is where it belongs and the other side is off the whole half inch, or what if one side is even in further than that, I hadn't measure to the end of the axle to see if they were at the correct distance from the end. So sure enough, one side was in a half inch, CRAP. So I figured I would cut that one off and then leave the other. Well, then I got to looking at the angle the rear end would be at where they were mounted, it was WAY off with the third member pointing up! Geeeez, I cut them both off and will clamp it all together until I have the engine tranny and height where I want it then get the pinion angle right and weld them on. I mean, come on, that's the right way to do it. I was just dreaming that the last guy had welded the perches on there right. One thing that was real nice, the dudes welds sucked so they was easy to remove. Brian Attached Images __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

02-26-2019, 02:03 AM	#2778
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: What did you do with your truck today, Part 3 My five minutes got me repairing the rear end housing where the perches were. So I got something done on the truck. Then I got a piece made for the trunk floor of my brothers '39. His is rusted, he bought this patch from a guy and it's only a little less rusted than his! So I used it as a pattern and made a patch for him. Brian Attached Images __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

02-26-2019, 06:01 PM	#2779
MiraclePieCo Registered User Join Date: Sep 2014 Location: USA Posts: 2,249	Re: What did you do with your truck today, Part 3 This is ridiculous. Snow has been on the ground for a full month here now. I've never seen that in my six decades living here. Since my garage is filled with the typical homeowner stuff - bicycles, lawnmowers, kayaks, etc - I usually move my panel truck into the driveway to work. Not possible for a month and no end in sight in the long range forecast. Snowing again now, and an entire county north of me without electricity for a week. Tried to eat at a local restaurant but they were closed because they couldn't get food through on the highways for a couple of days. So alas my truck languishes in the garage and I sit on my butt day after day waiting for Spring. Anyone else old enough to remember what scientists were predicting in the 1960s-70s? Looks like they were right! Attached Images __________________ 1951 Chevy Panel Truck

02-26-2019, 10:17 PM	#2781
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,639	Re: What did you do with your truck today, Part 3 Not a whole lot of progress going on around here unless you count snow shoveled paths. I did almost get out the the 51 1-1/2 ton though. Attached Images __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

02-26-2019, 10:34 PM	#2782
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,639	Re: What did you do with your truck today, Part 3 We didn't have enough snow to talk about all winter until February. I ran around outside in flanel shirts and no jacket a lot in Janurary and was getting stuff move aound so I could work on my shop and in February we have Had around 2 ft total snow in three weeks. We are supposed to get the tail end of the storm that Mirical Pie Co is gettng sometime in the next 24 and so far I haven't had to shovel the whole 400 ft but am afraid that the time is coming. Attached Images __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

02-26-2019, 10:35 PM	#2783
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: What did you do with your truck today, Part 3 WOW! Brian __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

02-27-2019, 12:03 AM	#2784
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: What did you do with your truck today, Part 3 My five minutes today was bringing my axle and steering goodies to the UPS store shipping it off to SIDS to be dropped and all the steering linkage modified, WHOOOO HOOOOO! Brian __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

02-27-2019, 03:25 AM	#2785
DransportGarage Registered User Join Date: Feb 2010 Location: Lebanon, Ohio Posts: 1,359	Re: What did you do with your truck today, Part 3 Sorry to see all the snow, guys! We've been lucky here in SW Ohio for the last several years. The plow was out once this year, and not at all last year (or was it the year before?). Conversely, in 2002 we got 14" the day after Christmas, and it was 25 below in 1977, when people were walking across the Ohio river: https://www.youtube.com/watch?v=3rXnNJhnfeo __________________ Bob "It won't take long and it won't cost much." '55 3100 (383/700R4)--'55 Belair Sedan (350/4-speed)--'64 'Vette Conv. (327/4-speed)--'68 GTO Conv. (462/4-speed)--'69 Cutlass Conv. (350/TH350)--'06 'Vette Conv. (LS2/6-speed) Bob's Retirement Build - My 55 TF Bob's 700R4 Build (how-to)

02-27-2019, 09:10 AM	#2786
Dyslexic Dog Registered User Join Date: Jul 2018 Location: GR MI Posts: 57	Re: What did you do with your truck today, Part 3 Sorry for the thread drift but I always like to engage the deniers. Rate of change. X squared. The peaks and valleys have not changed as much as the frequency. Weather is different then climate. Scientist theory is a theory that you test the data with. Guess what? Lots and lots and lots and lots of data support it. Of course you could always just believe a political oped piece instead.

02-28-2019, 09:53 AM	#2788
Kevin Mac Registered User Join Date: Nov 2016 Location: Central Missouri Posts: 170	Re: What did you do with your truck today, Part 3 I'm still changing my mind on my hydroboost install. I just wasn't comfortable with reservoir on firewall so I made another adapter plate to slant the HB and bough a new reservoir without as much angle. It will fit under floor with couple inches to spare. I will have to fill with syringe but figured how often do you have to add fluid. I don't know how you guys build from ground up, it would take me 10 years with changing my mind all the time. If anybody wants my 1/4" aluminum adapter plate and aluminum master cylinder push in adapters I made pay shipping and they are yours. The push in adapters have 1/8" pipe thread. Mac Attached Images

02-28-2019, 10:56 AM	#2790
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: What did you do with your truck today, Part 3 Yep, good stuff Mac! Brian __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

03-01-2019, 01:44 AM	#2791
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: What did you do with your truck today, Part 3 I got the heater motor rewired tonight. I would like to get the whole thing restored and waiting for installation, we well see. I need to have the core pressure tested, I'll see if I can get that done tomorrow. Brian __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

03-01-2019, 05:15 PM	#2792
MiraclePieCo Registered User Join Date: Sep 2014 Location: USA Posts: 2,249	Re: What did you do with your truck today, Part 3 Still snowbound here, big snow boulders pushed up by the plows across my driveway, so work on truck is5 limited. Electricity was out and no internet for 3 days. Using my phone to post this message. You may have heard about the Amtrak passengers stranded for days when their train became stuck in th snow near here. The only thing I've done on the truck is install my inside rear view mirror - whoopee! Edit: Just found this: the Governor has declared a State of Emergency for my county: Oregon Governor Kate Brown Declares State of Emergency in 10 Counties Hit by Winter Storms Oregon Governor Kate Brown has declared a state of emergency in ten counties because of severe winter storm conditions. Brown made the declaration Thursday for counties including Coos, Curry, Deschutes, Douglas, Jackson, Josephine, Klamath, Lane, Linn, and Marion. In a news release, Brown said the declaration will provide additional resources and the potential for federal highway system money for road fixes. The Oregon Office of Emergency Management will coordinate state resources from police to transportation workers to the National Guard to support local communities as needed. The resources will help communities recover from heavy snow and ice accumulation, high winds, flooding, and landslides. The state of emergency will last 30 days unless Brown ends it before then. In this region, Douglas County has been the hardest-hit area. The Douglas County Board of Commissioners and Douglas County Sheriff's Office have received many requests from people who want to help. __________________ 1951 Chevy Panel Truck Last edited by MiraclePieCo; 03-02-2019 at 05:32 AM.

03-01-2019, 09:24 PM	#2793
DransportGarage Registered User Join Date: Feb 2010 Location: Lebanon, Ohio Posts: 1,359	Re: What did you do with your truck today, Part 3 My five minutes (well, two hours.). I'm trying to figure out how to do a pocket for my sun visors and flames in my headliner. This is just a piece of cardboard and some scrap high density 1/4" foam and vinyl. I got incomplete distribution of glue because it was too thick, which caused bubbles in the vinyl, but I think I can do this if I throw this Harbor Fright gun away, pull out another one, and open a new can of Landau contact cement. Attached Images __________________ Bob "It won't take long and it won't cost much." '55 3100 (383/700R4)--'55 Belair Sedan (350/4-speed)--'64 'Vette Conv. (327/4-speed)--'68 GTO Conv. (462/4-speed)--'69 Cutlass Conv. (350/TH350)--'06 'Vette Conv. (LS2/6-speed) Bob's Retirement Build - My 55 TF Bob's 700R4 Build (how-to) Last edited by DransportGarage; 03-01-2019 at 09:35 PM.

03-01-2019, 10:33 PM	#2794
idbeast Senior Member Join Date: Oct 2016 Location: Olympia, WA Posts: 523	Re: What did you do with your truck today, Part 3 Well my 5 minutes was more like 7 hours of wet sanding everything except for the cab and bed cover, then loading it all up and taking it to the body shop for paint!



Register or Log In To remove these advertisements.

03-02-2019, 01:40 AM	#2795
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: What did you do with your truck today, Part 3 My five minutes didn't do a damn thing ON the truck darn it, boxed up some stuff I sold on eBay to buy stuff for the truck though. Brian __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

03-02-2019, 02:07 AM	#2796
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,639	Re: What did you do with your truck today, Part 3 Bought 245 bucks worth of firewood to keep the house warm. I did look up some parts for the truck while waiting for the wood to be delivered. Now I need to finish splitting my mom's wood and bring the splitter home and do mine. With all the snow on the ground I can't do much on the shop or the truck. __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

03-02-2019, 08:27 PM	#2797
mick53 Registered User Join Date: Oct 2018 Location: Warsaw IN Posts: 897	Re: What did you do with your truck today, Part 3 I took the king pins out of a 53 1/2 ton axle to give the spindles to a forum member. It's been a while since I did this and forgot what a pain it is. 20 ton press and torch. When they finally let lose they were hot and angry.

03-02-2019, 08:49 PM	#2798
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: What did you do with your truck today, Part 3 I am beat, don't know why but I am beat. I got out there and did some little crap. I am actually pleased with what I got done, a little on my heater, got up in the attic and some things inventoried, I got something done just not much for a whole day. Brian __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

03-02-2019, 09:32 PM	#2799
DransportGarage Registered User Join Date: Feb 2010 Location: Lebanon, Ohio Posts: 1,359	Re: What did you do with your truck today, Part 3 Cut the foam for the headliner flames... Attached Images __________________ Bob "It won't take long and it won't cost much." '55 3100 (383/700R4)--'55 Belair Sedan (350/4-speed)--'64 'Vette Conv. (327/4-speed)--'68 GTO Conv. (462/4-speed)--'69 Cutlass Conv. (350/TH350)--'06 'Vette Conv. (LS2/6-speed) Bob's Retirement Build - My 55 TF Bob's 700R4 Build (how-to)

Register or Log In To remove these advertisements.