What did you do to your truck today? Chapter II - Page 115 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

magwakeenercew2jh · 11-08-2015, 05:36 PM

Ordered one of these to feed the Street Demon.
Thanks for the tip, Waldoe.

truckkeepsmesane · 11-08-2015, 05:46 PM

Pulled the heater, pedals, finished up interior cab dissy.

Myoldtruck · 11-09-2015, 11:06 AM

It was a busy weekend. Installed new door locks and ignition lock. New drivers side glass weather stripping, new door arm rests. Installed a replacement horn and now its working. Got truck its Pa state inspection sticker. Still working on the wiper washer motor, not working yet.

Mator · 11-09-2015, 11:43 AM

Finally fixed my gas sending unit. Float was missing. 5 dollar part and 10 in shipping but at least now I know how much is in the tank.

midniteblues · 11-09-2015, 07:55 PM

Picked this kit off cl today hoping I can fit it nicely to my 67 swb stepper.
I'm sure I'll have too do some cutting and welding but it's a start and it'll save me some $.
Then I can take off my "fits all getter running dont disturb the nieghbor header mufflers". They work but they are loud but not nearly as loud as open headers going around the block.

Oh and also cleaned out the cowl and Got the radio,ebrake,dash lites and dome lite workin in the 1ton stepper it's about as far as I'm going with it,soon time To Send It Down The road.

**Elliot949** · 11-09-2015, 09:27 PM

Looked at Raymond sitting in the garage getting more and more pissed about the little body work things that the body shop screwed up... if it weren't for the little screw ups I could have this painted long ago... Also looked at Haulin in the driveway dead to the world... I have a short somewhere that keeps draining the battery and I haven't found it yet...

tommy3horse · 11-09-2015, 11:27 PM

Got a fresh Turbo 350 installed in Kazoo this weekend, and while off last week, installed a complete set of XRF balljoints. The joints are super nice, maybe better than Moog. The have a million-mile warranty and were a breeze to install.
Need an alignment and a pair of tires before winter, thats next.

BugzC10 · 11-10-2015, 08:15 AM

Quote:

Originally Posted by midniteblues

Picked this kit off cl today hoping I can fit it nicely to my 67 swb stepper.
I'm sure I'll have too do some cutting and welding but it's a start and it'll save me some $.
Then I can take off my "fits all getter running dont disturb the nieghbor header mufflers". They work but they are loud but not nearly as loud as open headers going around the block.

Oh and also cleaned out the cowl and Got the radio,ebrake,dash lites and dome lite workin in the 1ton stepper it's about as far as I'm going with it,soon time To Send It Down The road.

Do you have the p/n you bought? Keep us posted on the install. Especially interested since your truck is lowered.

iostorm · 11-10-2015, 08:22 AM

This

[IMG]

[/IMG]

iostorm · 11-10-2015, 10:19 AM

More on the photo above, takin it down to bare frame. Then sandblast and reassemble everything new. It's amazing how clean this truck is, once I powerwashed the bottom of the cab it is original red primer.

That 307 in the photo will be set aside in favor of a 400.

mmiddle · 11-10-2015, 12:26 PM

Began prepping the new roof clip for the transplant... I hate rust

greedy geezer · 11-10-2015, 05:07 PM

some of this

74baggedbug · 11-10-2015, 07:57 PM

Got the correct length brake hoses on the truck and upgraded to steel braided

wingnut6999 · 11-10-2015, 10:32 PM

Started working on the truck body today to see if there was any shine left. Used polishing compound and wax jus around the hood and gas cap. Up close you can see the fine cracks and scratches. Gives it character, I mean it ain't no show truck. Lol just my daily driver

midniteblues · 11-11-2015, 07:06 PM

Got it way up on stands today to start mocking up this exhaust. I put the tail pipes in and realized I needed the bumper on it so out it came.
I sure will need some cutting and welding.
But it's all good I can make it work.

Sorry dude I forgot too get the part # today.
Anyway it is a heart throb square body exhaust for those who want too know.

An since I was under there I took a few pics of the underneth as dusty an dirty as it can be.
U can see my do not disturb mufflers. And my custom crossmember.
It seems I found a new avatar for now.

9teen69 · 11-11-2015, 09:15 PM

Installed new steering wheel and cowl to hood seal.

**allchevy58** · 11-12-2015, 12:50 AM

Quote:

Originally Posted by 9teen69

Installed new steering wheel and cowl to hood seal.

Nice looking interior, like that steering wheel.

midniteblues · 11-13-2015, 08:24 AM

Well I got this far an that was the easy part.

I need to get gas for mr. Miller today I might have enough for a few more tacks.

The tail pipes are not gonna be fun.
But i do have 2 pcs of 3" x 24" long ss tubing that I'll make tips with.
Wish I would've pulled the bed off before starting oh well.

Nice steering wheel.i like it.

BugzC10 · 11-13-2015, 08:33 AM

Quote:

Originally Posted by midniteblues

Well I got this far an that was the easy part.

I need to get gas for mr. Miller today I might have enough for a few more tacks.

The tail pipes are not gonna be fun.
But i do have 2 pcs of 3" x 24" long ss tubing that I'll make tips with.
Wish I would've pulled the bed off before starting oh well.

Nice steering wheel.i like it.

Tight fit going over the axle?

midniteblues · 11-13-2015, 09:03 AM

Quote:

Originally Posted by BugzC10

Tight fit going over the axle?

Yhea it will be.
The intermediate pipes pretty much fell into place I might need a lil' shortening yet.
I have 67-69 camaro/68-74 Nova headers on my bb. They fit pretty good except they exited rite on a oe truck auto c member. So I made one. They don't hang below the frame.
Oh an the z bar needed a lil modding.
The tail pipes is where the "cutting and welding" part comes into play.
The ps isn't too bad but the ds. Is tight

UNEASYRIDER · 11-13-2015, 02:57 PM

Drove it in to work! Gave her a bath!

toolboxchev · 11-14-2015, 12:44 AM

100 bucks worth of electrical components, wires, plastic wiring retainers, spark plug wires, glove box, and finally wire gutters.

And I have not even scratched the surface.

74baggedbug · 11-14-2015, 09:38 AM

Yanked out the hid's and cheap halogen conversion and went to hella headlights and halogen bulbs and did the headlight relay mod.. Very happy with the results

mud.man.rj · 11-14-2015, 10:41 PM

That truck is so wallpaper worthy, shiny headlights and all.

In The Ten Ring · 11-15-2015, 12:37 AM

I stored the parts away in the garage.....it looks like a "cubicle" of boxed parts!

Oh my junked up garage!

11-08-2015, 05:36 PM	#2851
magwakeenercew2jh RAT1968 '68 Cab/'71 Parts Join Date: Feb 2002 Location: Coarsegold, CA Posts: 2,375	Re: What did you do to your truck today? Chapter II Ordered one of these to feed the Street Demon. Thanks for the tip, Waldoe. Attached Images __________________ M17 Coarsegold, CA RAT's shiny now. But always a rat.

11-08-2015, 05:46 PM	#2852
truckkeepsmesane Registered User Join Date: Apr 2015 Location: Jacksonville NC Posts: 58	Re: What did you do to your truck today? Chapter II Pulled the heater, pedals, finished up interior cab dissy. Attached Images __________________ 67 C20 to K20 Conversion 283 SM465 See my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=687765

11-09-2015, 11:06 AM	#2853
Myoldtruck Registered User Join Date: Sep 2015 Location: Mohnton pa. Posts: 208	Re: What did you do to your truck today? Chapter II It was a busy weekend. Installed new door locks and ignition lock. New drivers side glass weather stripping, new door arm rests. Installed a replacement horn and now its working. Got truck its Pa state inspection sticker. Still working on the wiper washer motor, not working yet.

11-09-2015, 11:43 AM	#2854
Mator Registered User Join Date: Jan 2013 Location: Clinton Iowa Posts: 337	Re: What did you do to your truck today? Chapter II Finally fixed my gas sending unit. Float was missing. 5 dollar part and 10 in shipping but at least now I know how much is in the tank. __________________ Build sheet http://67-72chevytrucks.com/vboard/s....php?p=7277491

11-09-2015, 07:55 PM	#2855
midniteblues Registered User Join Date: Jul 2011 Location: strausstown pa Posts: 3,394	Re: What did you do to your truck today? Chapter II Picked this kit off cl today hoping I can fit it nicely to my 67 swb stepper. I'm sure I'll have too do some cutting and welding but it's a start and it'll save me some $. Then I can take off my "fits all getter running dont disturb the nieghbor header mufflers". They work but they are loud but not nearly as loud as open headers going around the block. Oh and also cleaned out the cowl and Got the radio,ebrake,dash lites and dome lite workin in the 1ton stepper it's about as far as I'm going with it,soon time To Send It Down The road. Attached Images __________________ 81 camaro 355 4/spd 342 posi my first love. 67 swb step 454/4spd ott 373 posi 4/7 drop. 2000 s10 zr2 little blue truck that never gets stuck. '74 heald super bronc vt8. tecumseh powered moon rover.

11-09-2015, 09:27 PM	#2856
Elliot949 Registered User Join Date: Sep 2010 Location: Winfield, Ks. Posts: 4,162	Re: What did you do to your truck today? Chapter II Looked at Raymond sitting in the garage getting more and more pissed about the little body work things that the body shop screwed up... if it weren't for the little screw ups I could have this painted long ago... Also looked at Haulin in the driveway dead to the world... I have a short somewhere that keeps draining the battery and I haven't found it yet... __________________ Dan Johnston... Owner of My Dad's- '67 Chevy C-20 Custom Camper Short Fleetside Pickup PAPA J And our newest addition a- '71 Chevy CST/10 Short Fleetside Pickup Haulin' SOLD Papa J's Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=612847 Haulin's Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=671130SOLD B Bears Build Thread:http://67-72chevytrucks.com/vboard/s...d.php?t=744210

11-09-2015, 11:27 PM	#2857
tommy3horse Registered User Join Date: Feb 2015 Location: St. Clair, Missouri Posts: 124	Re: What did you do to your truck today? Chapter II Got a fresh Turbo 350 installed in Kazoo this weekend, and while off last week, installed a complete set of XRF balljoints. The joints are super nice, maybe better than Moog. The have a million-mile warranty and were a breeze to install. Need an alignment and a pair of tires before winter, thats next. __________________ 1972 GMC C1500 350/350 1965 Mustang 2+2 289 4spd, show-car 1965 Mustang Coupe 289 4spd, stoplight racer 1/2 dozen Wheelhorse Tractors

11-10-2015, 08:22 AM	#2859
iostorm Registered User Join Date: Oct 2015 Location: Grafton Ohio Posts: 94	Re: What did you do to your truck today? Chapter II This [IMG][/IMG]

11-10-2015, 10:19 AM	#2860
iostorm Registered User Join Date: Oct 2015 Location: Grafton Ohio Posts: 94	Re: What did you do to your truck today? Chapter II More on the photo above, takin it down to bare frame. Then sandblast and reassemble everything new. It's amazing how clean this truck is, once I powerwashed the bottom of the cab it is original red primer. That 307 in the photo will be set aside in favor of a 400.

11-10-2015, 12:26 PM	#2861
mmiddle Registered User Join Date: Jul 2013 Location: Forestburg, Texas Posts: 659	Re: What did you do to your truck today? Chapter II Began prepping the new roof clip for the transplant... I hate rust Attached Images __________________ Mark Jesus is the Way! 2003 2500HD CCLB Duramax/Ali (Clifford) 2014 2SS/RS black on black Camaro (Betty) 2006 Pontiac SOLSTICE silver/black (Lula-Bell) 1970 C/10 Short Wide (Peggy) 1964 C/10 Short Step (Hambone) RIP Jimmy Hamilton Thank you for the trucks

11-10-2015, 05:07 PM	#2862
greedy geezer Registered User Join Date: Oct 2015 Location: Stoughton MA where everyhing on the road gets rusted out from winter and rock salt Posts: 168	Re: What did you do to your truck today? Chapter II some of this Attached Images

11-10-2015, 07:57 PM	#2863
74baggedbug Registered User Join Date: Oct 2011 Location: Houston tx Posts: 701	Re: What did you do to your truck today? Chapter II Got the correct length brake hoses on the truck and upgraded to steel braided

11-10-2015, 10:32 PM	#2864
wingnut6999 Registered User Join Date: Jul 2015 Location: East Springfield ohio Posts: 20	Re: What did you do to your truck today? Chapter II Started working on the truck body today to see if there was any shine left. Used polishing compound and wax jus around the hood and gas cap. Up close you can see the fine cracks and scratches. Gives it character, I mean it ain't no show truck. Lol just my daily driver Attached Images

11-11-2015, 07:06 PM	#2865
midniteblues Registered User Join Date: Jul 2011 Location: strausstown pa Posts: 3,394	Re: What did you do to your truck today? Chapter II Got it way up on stands today to start mocking up this exhaust. I put the tail pipes in and realized I needed the bumper on it so out it came. I sure will need some cutting and welding. But it's all good I can make it work. Sorry dude I forgot too get the part # today. Anyway it is a heart throb square body exhaust for those who want too know. An since I was under there I took a few pics of the underneth as dusty an dirty as it can be. U can see my do not disturb mufflers. And my custom crossmember. It seems I found a new avatar for now. Attached Images __________________ 81 camaro 355 4/spd 342 posi my first love. 67 swb step 454/4spd ott 373 posi 4/7 drop. 2000 s10 zr2 little blue truck that never gets stuck. '74 heald super bronc vt8. tecumseh powered moon rover.

11-11-2015, 09:15 PM	#2866
9teen69 Registered User Join Date: Sep 2002 Location: Austin, Texas Posts: 1,048	Re: What did you do to your truck today? Chapter II Installed new steering wheel and cowl to hood seal. Attached Images __________________ 72 Cheyenne SWB C10 (daily driver) (Super fake cause I just love the glovebox emblem) 70 Camaro RS (frame-off in pieces) 70 Camaro RS (daily driver backup) 69 Custom LWB C10 (son now drives)



Register or Log In To remove these advertisements.

11-13-2015, 08:24 AM	#2868
midniteblues Registered User Join Date: Jul 2011 Location: strausstown pa Posts: 3,394	Re: What did you do to your truck today? Chapter II Well I got this far an that was the easy part. I need to get gas for mr. Miller today I might have enough for a few more tacks. The tail pipes are not gonna be fun. But i do have 2 pcs of 3" x 24" long ss tubing that I'll make tips with. Wish I would've pulled the bed off before starting oh well. Nice steering wheel.i like it. Attached Images __________________ 81 camaro 355 4/spd 342 posi my first love. 67 swb step 454/4spd ott 373 posi 4/7 drop. 2000 s10 zr2 little blue truck that never gets stuck. '74 heald super bronc vt8. tecumseh powered moon rover.

11-13-2015, 02:57 PM	#2871
UNEASYRIDER Registered User Join Date: Apr 2009 Location: PHOENIX,ARIZONA Posts: 91	Re: What did you do to your truck today? Chapter II Drove it in to work! Gave her a bath! __________________ DON'T BUILD IT IF YOUR NOT GONA DRIVE IT!!

11-14-2015, 12:44 AM	#2872
toolboxchev Registered User Join Date: Jul 2015 Location: 2nd left past the stump on a dirt road. Posts: 2,629	Re: What did you do to your truck today? Chapter II 100 bucks worth of electrical components, wires, plastic wiring retainers, spark plug wires, glove box, and finally wire gutters. And I have not even scratched the surface.

11-14-2015, 09:38 AM	#2873
74baggedbug Registered User Join Date: Oct 2011 Location: Houston tx Posts: 701	Re: What did you do to your truck today? Chapter II Yanked out the hid's and cheap halogen conversion and went to hella headlights and halogen bulbs and did the headlight relay mod.. Very happy with the results

11-14-2015, 10:41 PM	#2874
mud.man.rj Registered User Join Date: Dec 2011 Location: Creighton Sask. Canada Posts: 4,121	Re: What did you do to your truck today? Chapter II That truck is so wallpaper worthy, shiny headlights and all. __________________ 1987 Green n Green machine. 5.0 4spd std. 7" lift w 35's.

11-15-2015, 12:37 AM	#2875
In The Ten Ring Registered User Join Date: Jun 2013 Location: West Virginia Posts: 6,421	Re: What did you do to your truck today? Chapter II I stored the parts away in the garage.....it looks like a "cubicle" of boxed parts! Oh my junked up garage!

Register or Log In To remove these advertisements.