67 Camaro Build

[7dee2]

OE rear window trim and drip rail moldings are being tested no issues so far. Kelly also fixed the small golf ball dent in the fender extension mentioned earlier.

[7dee2]

So, the other 2 shifters are reassembled with the main stick replacement on one and some minor parts on both. Still have 4 complete Ram 4 shifters with linkage for just one car aka “The Hoard”! I should start selling off most of the other shifters including my V-Gate stuff now that I’ve settled on what I’m running.

Side note: To date, that selling-off stuff hasn’t really happened yet in fact I did just barely pick up another Ram 4 boot.

[regan wilson]

Even wrecked race cars bring good money for the VIN.

[7dee2]

Thanks CG, I’m glad you’re enjoying the build. It’s fun going back and putting words to the pictures, telling The Good, the Bad, and the Ugly story "ah ee ah ee ah wah wah wah".

It is surprising how much Camaro shells can bring, and the lengths folks will go to save them. The good thing is it’s made for a stronger aftermarket for not only the Camaro but most muscle cars from the big three. I hope it continues and as David Freiburger says “Gasoline Forever”!




One shifter piece that always seems to be missing is this little plastic flange bearing, they get brittle over time and disintegrate. When that happens the pull-up trigger rod will rub against the stick so it's metal on metal, it ruins the rod over time and is noticeable when using the shifter. Found a very close replacement on ebay (link), just remove the locator tab and it’s a good match. With a lot of 50, we now have several lifetimes of replacements. https://www.ebay.com/itm/262376570626

[regan wilson]

Originally Posted by 7dee2

Thanks CG, I’m glad you’re enjoying the build. It’s fun going back and putting words to the pictures, telling The Good, the Bad, and the Ugly story "ah ee ah ee ah wah wah wah".

It is surprising how much Camaro shells can bring, and the lengths folks will go to save them. The good thing is it’s made for a stronger aftermarket for not only the Camaro but most muscle cars from the big three. I hope it continues and as David Freiburger says “Gasoline Forever”!




One shifter piece that always seems to be missing is this little plastic flange bearing, they get brittle over time and disintegrate. When that happens the pull-up trigger rod will rub against the stick so it's metal on metal, it ruins the rod over time and is noticeable when using the shifter. Found a very close replacement on ebay (link), just remove the locator tab and it’s a good match. With a lot of 50, we now have several lifetimes of replacements. https://www.ebay.com/itm/262376570626

Nice progress Mr Shifter Hoarder. I dig the GBU cartoon as well. Keep up the good work.

[7dee2]

Ha, Thanks Regan.

Here are the best parts of our 3 shifters into 1 with a new re-chromed stick, handles, and hardware. Oh yes, it's a beauty!

[7dee2]

And a mockup of the restored shifter with NOS rods, levers, buttons, new bushings, hardware, etc.

[Troy Sr]

Hey looks great, I like the look of the tranny!! What's the bar welded across the timing cover for? I've never seen that before!!!

[7dee2]

Thank you Troy. I think it has to do with minimizing timing cover flex when retrofitting a roller cam and button into an earlier SBC/BBC without a cam retainer plate. It’s an old racer trick to strengthen the cover and aid in perfect timing, limiting the cam movement. He also ground the timing tab to a point at true TDC with our degreed balancer. Mike "Gold" Lane really went the extra mile and did lots of cool go-fast stuff for the 511.



After a few trips to the parts store, I’m satisfied that we have some correct-length fan belts. Not a lot of adjustment here due to the taller valve covers. Early high-performance big blocks used to run a short belt from the water pump to the crank (no adjustment) when equipped with manual steering. This type of alternator bracket pulley setup is found on L72/L88 427’s which is the look for our day two, Grumpy’s Toy, Motion mash-up car. I just can’t bring myself to paint everything flat black like the Grump so famously did.

[7dee2]

Just for fun, I decided to bolt on the carb and our old fly-eye air cleaner. If I remember correctly the replacement filter material, bought off eBay years ago is supposed to be flame retardant (?).

Here’s an old pic of Bill “Grumpy” Jenkins at the 1967 NHRA Nationals, this shot reminds me so much of Terry “The Tiger” from American Graffiti.

[69cam]

Looks great! Never thought of it but they could be brothers.

[Troy Sr]

My step brother had a V8 Vega back in the old days and he had one of those air cleaners!!! The problem is it always back fired and burned the filter!!!

[ghackett1]

That was a great thread! Car is awesome. Here’s a pic of my 68 convertible, figured you would like it.

[7dee2]

I appreciate that thank you ghackett1. You’re right, that’s a very nice looking 68 you have there.



It’s a good thing that they do make a long reach gasket type plug with a 5/8” body that fixes this issue (link is to what I bought). https://www.ngk.com/ngk-6364-bkr6es-nickel-spark-plug This plug is so much better, future tune-ups got much easier thanks to Mark’s advice.

The last pic is just fun to get some rating action started, thanks everyone for following!

[7dee2]

This is an internally regulated 12si high output alternator that’ll keep up with all the power needs of the not so Day 2 stuff we’ll be using. Currently (Ha get it, currently ) re-clocking it as these always come clocked for a passenger side mount not drivers. Already changed out the pulley for an old school deep groove. I like these alternators they have an old school look and still give plenty of juice for electric fans, fuel pumps, A/C, stereos, etc.

https://www.summitracing.com/parts/pwm-47293

[7dee2]

The orange headers are really growing on me. Like Chevy Chase said, “Yes! Ahhh Hahahaaa, I Like It!”

https://www.youtube.com/watch?v=8zdlZgJ1sk8

[joesscamaro]

I love the orange headers! Thanks for the updated pics!

[CAMAROBOY68SS]

Have you had the motor in the car with that HEI set in? I know on a first gen they are really tight to the firewall with stock towers on the subframe. I have a buddy with a 67 and a small block and every couple years it seams it touches just enough over time to crack the cap, even with new motor mounts and transmission mount.

[7dee2]

Originally Posted by joesscamaro

I love the orange headers! Thanks for the updated pics!

You bet, thank you Joe, I appreciate it.

Originally Posted by CAMAROBOY68SS

Have you had the motor in the car with that HEI set in? I know on a first gen they are really tight to the firewall with stock towers on the subframe. I have a buddy with a 67 and a small block and every couple years it seams it touches just enough over time to crack the cap, even with new motor mounts and transmission mount.

Yes I have mocked a big block in our car with the BB stands, poly mounts, BB manual cross member, and a poly trans mount. I was relieved that the HEI does clear the firewall nicely.
http://67-72chevytrucks.com/vboard/s...&postcount=165



Window trim fitment is not going very well for the windshield, both OE and aftermarket. This particular area normally is not that great on first-gen Camaros anyway. Kelly discovered with our car the windshield opening at the top is just a bit wider (roughly a 1/4”) than a factory car, not good. Another frustration is the dang molding clip studs have been popping off both front and rear (mainly from the roof skin) during this process, moving to a screw-in style stud for the fix. The sharpie marks around the back window are clip locations.

The good news (I’ll mention this again) is that the back window trim both OE and aftermarket fits great.

[7dee2]

Time to check out the C10 489 build (you know "Why build one when you can have two at twice the price..." ) that’s been in process at Fastlane Machine. The block has been completely machined, deburred, and cleaned, Mike was just about to start assembling this motor.

I’m very excited to see how it will compare with our “Good to go!” 511. With a little less stroke, bore, cam, iron vs aluminum head, intake configuration (air gap vs factory dual plane, oval vs rectangle port) as well as a vacuum vs mech secondary 850 Holley.

[7dee2]

The lower body lines and gaps at the back of the doors needed more work, Kelly has both sides dialed in. Also, a temporary install of the windshield to help aid with the trim fitment. He’s been working the windshield opening and it is getting better. But the trim barely covers the upper opening and is still not fitting quite right.

The fenders, hood, and cowl panel also went back on while this windshield is in to check the lower trim fitment. More to come on what was found…

[72 tigger]

Thanks for your updates
This is going to be a piece of art when done

[Lost in the 60's]

The lower windshield trim never did fit right from the factory, especially the fenders tucking up under it, like it is supposed to do. You will notice many cars at shows with a gap there, some huge. My '67 will require shims under the core support to close those gaps up too.

[joesscamaro]

That's definitely news you don't want to hear but it sounds like the car is in good hands and will come out looking A-OK.

[7dee2]

Thanks Joe, you’re right and that’s exactly why all this mockup work is being done to catch this kind of stuff.



After the “SLIGHTLY OUT OF ALIGNMENT!!!” moment it was decided to triple-check the side glass again. Especially the right-side glass including the upper weatherstripping on both sides this time. Kelly found the same thing that I did, it just fits without much adjustment on that side. The good news is it looks perfect and will function fine and shouldn’t cause any issues.

Decided to grab the inner fender wells from the body shop. Thought if I predrilled the tiny holes, it might make installing the splash shields staples easier (?) when they come back painted.