Power Steering Adapter Plates

[Str8axle]

Cap'n, I'm ready for a bracket and a tube+flange for my '65. These look top notch!

[Sizemore 65]

Captain, I would like to get two power steering plates, one tube and flange, and one powder coated power brake adapter plate.

Thanks
Aaron

[Captainfab]

I replied to your PM T Smith.....

Originally Posted by T Smith

Need a bracket for my 66, PM sent.

I'll send you both PM's with ordering info.

Originally Posted by Str8axle

Cap'n, I'm ready for a bracket and a tube+flange for my '65. These look top notch!

Originally Posted by Sizemore 65

Captain, I would like to get two power steering plates, one tube and flange, and one powder coated power brake adapter plate.

Thanks
Aaron

[Gabriel314]

Hello Captin Fab I have a 68 short bed looking to install your plate I currently have washers inbetween frame and box Iam a new member so where do we start? What's a PM?
Posted via Mobile Device

[Captainfab]

Hello. Do you have a '68 C series or a K series truck?

On a '68 C series frame, you shouldn't need any spacers at all, as '68 was the firest year that integral power steering was available on the C series trucks. Perhaps your frame is an early '68 or a '67 frame. In that case all you need are four 1/4" spacers, which I do also sell for $4.00 each plus shipping. You really don't need thos adapter plate for your frame unless you have a K series truck. Then this adapter plate will work for you.

A PM is a Private Message, which is basically an email that is restricted to just this forum. One way to send one is to click on "User CP" and then scroll down to where you see "New Message" on the left under the "Private Message" category. Or you can send me an email at captainfab454 at hotmail dot com

Let me know what you have, and we'll go from there.

Originally Posted by Gabriel314

Hello Captin Fab I have a 68 short bed looking to install your plate I currently have washers inbetween frame and box Iam a new member so where do we start? What's a PM?
Posted via Mobile Device

[Gabriel314]

I believe I have a c10 1/2 ton 6 lug with a 250 4 speed manual. Yea my frame definitely doesn't have the Dimple this is why I used two washers for each bolt about a 1/4 inch thick. I will take the spacers.
Posted via Mobile Device

[xxboondockxx]

Hello Captain. I need info on pricing for an adapter plate and the steering column shaft adapter/rag joint.
1966 C20, 350 engine

May have PM'd twice.

Thanks

[Captainfab]

I replied to your PM.......

Originally Posted by xxboondockxx

Hello Captain. I need info on pricing for an adapter plate and the steering column shaft adapter/rag joint.
1966 C20, 350 engine

May have PM'd twice.

Thanks

[BK'66Step]

Hey Captain, I plan on PM'ing you soon to order one of your power steering box brackets but I have a question. I have the cab off of the frame and am in the process of cleaning it up and painting it. Will I need to put the cab and steering column back on the truck to install the bracket properly or do the directions already locate it where it needs to be without having to line it up with the steering column? I would wait until later to do it but I would rather weld this in place now before painting. Thanks!!

[Captainfab]

You do not have to have the cab on the frame to install the power steering box and adapter plate. The installation instructions and the template make it easy to get the steering box located just where it needs to be. You probably will want to have the cab in place when you shorten the steering column with either the original flange or the tube and flange that I also sell.

[BK'66Step]

Thank you much!! I'll be in touch soon! :-)

[Formanbob]

do you have to drill the frame?

[Captainfab]

Yes the frame has to be drilled for the power steering box. There is no way around it.

Originally Posted by Formanbob

do you have to drill the frame?

[Formanbob]

You got pm
Posted via Mobile Device

[Captainfab]

I sent you a reply......

Originally Posted by Formanbob

You got pm
Posted via Mobile Device

[Formanbob]

Originally Posted by Captainfab

I sent you a reply......

back at you

[williamsboys]

I would like to get one of the brackets from ya.
Posted via Mobile Device

[Captainfab]

I'll send you a PM with order and payment details.

Originally Posted by williamsboys

I would like to get one of the brackets from ya.
Posted via Mobile Device

[MisterC]

PM sent, but this is mostly a bump for your product since you always respond timely.

[Captainfab]

Thanks MisterC

I replied to your PM.

Originally Posted by MisterC

PM sent, but this is mostly a bump for your product since you always respond timely.

[myles66]

Hey capt., I have a chance of getting a fairly cheap 59-70 impala brake booster/ master cylinder. My question is will you're brake booster adapter work with that setup on a 66 c1000?
Posted via Mobile Device

[Captainfab]

I'm not sure on that wide of a year spread, but the '70-'74 Impala/Caprice booster does fit the booster brackets that I make and sell.

Originally Posted by myles66

Hey capt., I have a chance of getting a fairly cheap 59-70 impala brake booster/ master cylinder. My question is will you're brake booster adapter work with that setup on a 66 c1000?
Posted via Mobile Device

[dmgibbs]

I need one of your power steering adapter plates and a drawing of where i need to drill the holes Will you take a money order?
David Gibbs
Mount Olive Al

[Captainfab]

Every power steering box adapter plate comes with the template and installation instructions. Yes I accept money orders. I'll send you a PM with details.

Originally Posted by dmgibbs

I need one of your power steering adapter plates and a drawing of where i need to drill the holes Will you take a money order?
David Gibbs
Mount Olive Al

[dmgibbs]

Send me your address and the amount to;
David Gibbs
Dmgibbs5980@Gmail.com

I need one to fit a 1966 chev