Project#2 67-72 Restoration's Shop truck - Page 12 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

VA72C10 · 10-03-2012, 09:04 PM

Dimpled the frame for ps earlier....also working on the trac bar and shock mount install...

Put my battery on the charger and it's already reading 12.5 so I'm not going to charge it....I have it handy if needed but should be good to start up....
Posted via Mobile Device

VA72C10 · 10-03-2012, 09:06 PM

Quote:

Originally Posted by Xeen

Just 9 days to go before the meet, it's time to break out the Superman suit

Some dirty shop clothes will have to do

Quote:

Originally Posted by BMERDOC

I didn't think you caught that! I tossed and turned until 4 in the morning! I had a busy mind and couldn't sleep. I'm working on 3 hours of sleep today.

Glad to see the trans 'member came and and good thing its not raw...one less thing to paint! Cross your fingers that engine/trans installation goes smoothly!

Sorry you couldn't sleep....thinking of bagging your truck weren't you?

Speaking of the engine/trans install...I sent you a text

Posted via Mobile Device

Xeen · 10-03-2012, 09:20 PM

My guess is from the time he gets there you two will have the truck running and driving in 6 hours or less.
Ohhhh its a time challenge.
You two can play beat the clock.

Of course that is all predicated on the idea that you are both working and one guy isnt sitting around supervising the other guy working

VA72C10 · 10-04-2012, 12:08 AM

If one of us gets to sit i'd like that job

Will update with pictures and progress tomorrow
Posted via Mobile Device

VA72C10 · 10-04-2012, 04:17 AM

Who am I kidding...I'll update tonight

or is it this morning technically

Have to tighten a few bolts and connect the e-brake and brake lines....also have to swap the lower bolts in the bags....need 4 1/2" and had 5" so they won't tighten all the way of course...

Also going to trim down the rear bumpstop for now....they will be removed completely when I notch it...
Posted via Mobile Device

VA72C10 · 10-04-2012, 04:23 AM

Couple pics with it still jacked up and one with it on the bumpstops. Also of course will need to run the air management....might do schraeder valves for now...
Posted via Mobile Device

VA72C10 · 10-04-2012, 04:27 AM

And things always happen for a reason....remember my steering wheel I was upset at myself for ruining the paint with a hurried clear coat?

I'm upset no more

Aircraft stripper took off all the new paint as well as the red paint that was on there....leaving a fawn wheel

there are a couple small cracks....but once I finish stripping the paint and hose it off/clean it up....i'm using this wheel the way it is

Posted via Mobile Device
Posted via Mobile Device

XxCHEVYMANxX · 10-04-2012, 07:27 AM

Nice job man ! movin right along. nice save on the wheel too !

CC69Rat · 10-04-2012, 07:57 AM

No notch?

Bennett68C10 · 10-04-2012, 08:04 AM

Looking Good

Rusbuilt · 10-04-2012, 09:08 AM

Nice! I want bags!! lol

VA72C10 · 10-04-2012, 11:06 AM

Quote:

Originally Posted by XxCHEVYMANxX

Nice job man ! movin right along. nice save on the wheel too !

Thanks!

Quote:

Originally Posted by CC69Rat

No notch?

The plan is to build my own notch when I put the accuair e-level on. Just running out of time for the 13th to at least have it on the road....

Quote:

Originally Posted by Bennett--G4L

Looking Good

Thanks!

Quote:

Originally Posted by Rusbuilt

Nice! I want bags!! lol

Me too

. I put them on my first truck but never finished that one because of a layoff. Then had one with bags in the rear for a few months that I had to sell to get the cash to finish my blazer project.

So this will be my first bagged driver....been looking forward to it now since I joined the board.....20k+ posts later and I'm here

Posted via Mobile Device

VA72C10 · 10-04-2012, 11:10 AM

I will also see how it rides with the bag "hats". Have heard some complaints of not enough air in the bags but from what I've read those guys didn't have 2" blocks (2 1/4 effective with the ece trac bar setup) and they rode with the trucks really low....I don't care to ride super low....just at a 4/6 or 5/7 drop....so I "should" have plenty of air in the bags at ride height....

If not, when I notch it I will remove the hats and drill directly through the frame for the air fittings.

Will get some pictures in a few min....
Posted via Mobile Device

Xeen · 10-04-2012, 11:32 AM

The speed at which you are getting this thing done is just crazy impressive.
You never know you still might have time to get extra things done because if it rains one day before the 13th you can fabricate your notches and then the next morning you can instal them and you will be all set

VA72C10 · 10-04-2012, 12:19 PM

Quote:

Originally Posted by Xeen

The speed at which you are getting this thing done is just crazy impressive.
You never know you still might have time to get extra things done because if it rains one day before the 13th you can fabricate your notches and then the next morning you can instal them and you will be all set

Thanks. Since this is my planned career I've been putting a ton of time in each day. Most days a minimum of 6 hours....some days as many as 14 hours with interruptions between and some of that time buying parts and of course posting on here

Posted via Mobile Device

VA72C10 · 10-04-2012, 12:24 PM

Posted via Mobile Device
Posted via Mobile Device

NewType72 · 10-04-2012, 12:25 PM

Can't wait to see the "unfinished"product in the end have been watching with anticipation and drive for working on my own cab to get ready for my big frame off project
Posted via Mobile Device

VA72C10 · 10-04-2012, 12:50 PM

Thanks, will have a lot more still to do on the truck after the meet. Bed wood, new door window seals, new (nice used) door guts, the c-notch and accuair system,.......

And down the road I really want to do an ls swap.
Posted via Mobile Device

BMERDOC · 10-04-2012, 01:55 PM

Sa weet pics of the rear suspension! I'll be bringing most of the tools back and all the brake fluid I can carry. Need anything else?

VA72C10 · 10-04-2012, 02:17 PM

Need a 1 1/8" socket but I think I will pick one up to have...if you can bring a better 1/2" drive ratchet than the one I have so I can tighten up everything in the rear that would be great.
Posted via Mobile Device

Xeen · 10-04-2012, 03:07 PM

I had to buy a Craftsman 3/4" breaker bar and 1-1/8", 1-1/16", 3/4" sockets to remove some of the nuts on the rear end of my truck because I broke three craftsman 1/2" Ratchet Drivers and a 1/2" breaker bar before I realized I needed a 3/4" breaker bar LOL

CC69Rat · 10-04-2012, 04:16 PM

Nothing like a tight rear ..

NewType72 · 10-05-2012, 01:00 AM

Best comment on the build so far ^

VA72C10 · 10-05-2012, 01:05 AM

Engine and trans are IN!

Despite a few bolts that didn't want to cooperate we got them mounted up. Bmerdoc also helped me button up the steering so now all that needs is the pump and lines ran...(and the wheel

)

HUGE thanks to Nick (bmerdoc) for coming by again after work and staying late. Remember guys, he's working on getting his truck ready for our upcoming meet also!

Stil have to tighten the tubular crossmember bolts and install the torque converter to flywheel bolts but a BIG step forward tonight. Hoping I can get everything else buttoned up so Sunday Sunday Sunday we can fire it up!

Posted via Mobile Device

VA72C10 · 10-05-2012, 01:08 AM

Posted via Mobile Device

10-03-2012, 09:04 PM	#276
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Project#2 67-72 Restoration's Shop truck Dimpled the frame for ps earlier....also working on the trac bar and shock mount install... Put my battery on the charger and it's already reading 12.5 so I'm not going to charge it....I have it handy if needed but should be good to start up.... Posted via Mobile Device __________________ Looking for a 67-72 swb or blazer project in or around VA.

10-03-2012, 09:20 PM	#278
Xeen Registered User Join Date: Aug 2012 Location: Topeka Kansas Posts: 2,655	Re: Project#2 67-72 Restoration's Shop truck My guess is from the time he gets there you two will have the truck running and driving in 6 hours or less. Ohhhh its a time challenge. You two can play beat the clock. Of course that is all predicated on the idea that you are both working and one guy isnt sitting around supervising the other guy working __________________ Please call me Brian. Check out My 1972 SWB Fleetside 5.3L Vortec Restomod Build

10-04-2012, 12:08 AM	#279
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Project#2 67-72 Restoration's Shop truck If one of us gets to sit i'd like that job Will update with pictures and progress tomorrow Posted via Mobile Device __________________ Looking for a 67-72 swb or blazer project in or around VA.

10-04-2012, 04:17 AM	#280
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Project#2 67-72 Restoration's Shop truck Who am I kidding...I'll update tonight or is it this morning technically Have to tighten a few bolts and connect the e-brake and brake lines....also have to swap the lower bolts in the bags....need 4 1/2" and had 5" so they won't tighten all the way of course... Also going to trim down the rear bumpstop for now....they will be removed completely when I notch it... Posted via Mobile Device __________________ Looking for a 67-72 swb or blazer project in or around VA.

10-04-2012, 04:23 AM	#281
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Project#2 67-72 Restoration's Shop truck Couple pics with it still jacked up and one with it on the bumpstops. Also of course will need to run the air management....might do schraeder valves for now... Posted via Mobile Device Attached Images __________________ Looking for a 67-72 swb or blazer project in or around VA.

10-04-2012, 04:27 AM	#282
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Project#2 67-72 Restoration's Shop truck And things always happen for a reason....remember my steering wheel I was upset at myself for ruining the paint with a hurried clear coat? I'm upset no more Aircraft stripper took off all the new paint as well as the red paint that was on there....leaving a fawn wheel there are a couple small cracks....but once I finish stripping the paint and hose it off/clean it up....i'm using this wheel the way it is Posted via Mobile Device Posted via Mobile Device Attached Images __________________ Looking for a 67-72 swb or blazer project in or around VA.

10-04-2012, 07:27 AM	#283
XxCHEVYMANxX Registered User Join Date: Oct 2010 Location: Decatur, IL. Posts: 628	Re: Project#2 67-72 Restoration's Shop truck Nice job man ! movin right along. nice save on the wheel too ! __________________ *John* Mild Custom 68' Work Truck Build Facebook LoL 1977 Trans Am (Project) 1965 Chevelle (Project)

10-04-2012, 07:57 AM	#284
CC69Rat Registered User Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,209	Re: Project#2 67-72 Restoration's Shop truck No notch? __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

10-04-2012, 08:04 AM	#285
Bennett68C10 Registered User Join Date: Dec 2006 Location: Toms River, NJ Posts: 5,518	Re: Project#2 67-72 Restoration's Shop truck Looking Good __________________ Keith 66 Suburban Burb Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=751361 IG: bennett68c10

10-04-2012, 09:08 AM	#286
Rusbuilt Registered User Join Date: Mar 2012 Location: Knoxville, TN Posts: 5,381	Re: Project#2 67-72 Restoration's Shop truck Nice! I want bags!! lol __________________ -Rus PLEASE HELP WITH PROJECT UNDERHAULINPaypal donations accepted @ rus1785@yahoo.com Rusbuilt's garage 1968 Chevy C-30 Darcy SOLD Rusbuilt shop truck *SOLD*

10-04-2012, 11:10 AM	#288
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Project#2 67-72 Restoration's Shop truck I will also see how it rides with the bag "hats". Have heard some complaints of not enough air in the bags but from what I've read those guys didn't have 2" blocks (2 1/4 effective with the ece trac bar setup) and they rode with the trucks really low....I don't care to ride super low....just at a 4/6 or 5/7 drop....so I "should" have plenty of air in the bags at ride height.... If not, when I notch it I will remove the hats and drill directly through the frame for the air fittings. Will get some pictures in a few min.... Posted via Mobile Device __________________ Looking for a 67-72 swb or blazer project in or around VA.

10-04-2012, 11:32 AM	#289
Xeen Registered User Join Date: Aug 2012 Location: Topeka Kansas Posts: 2,655	Re: Project#2 67-72 Restoration's Shop truck The speed at which you are getting this thing done is just crazy impressive. You never know you still might have time to get extra things done because if it rains one day before the 13th you can fabricate your notches and then the next morning you can instal them and you will be all set __________________ Please call me Brian. Check out My 1972 SWB Fleetside 5.3L Vortec Restomod Build

10-04-2012, 12:24 PM	#291
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Project#2 67-72 Restoration's Shop truck Posted via Mobile Device Posted via Mobile Device Attached Images __________________ Looking for a 67-72 swb or blazer project in or around VA.

10-04-2012, 12:25 PM	#292
NewType72 Registered User Join Date: Feb 2012 Location: turlock Posts: 2,177	Re: Project#2 67-72 Restoration's Shop truck Can't wait to see the "unfinished"product in the end have been watching with anticipation and drive for working on my own cab to get ready for my big frame off project Posted via Mobile Device __________________ Project NewType 1972 Chevy C/10 Cheyenne Super ( Daily Driven Showtruck ) http://67-72chevytrucks.com/vboard/s...d.php?t=507903 Project Great Grandpa's Legacy 1973 Chevy C/10 Cheyenne ( Current daily driver collecting big time parts ) http://67-72chevytrucks.com/vboard/s...89#post7084289 - Dylan (209)-985-7721

10-04-2012, 12:50 PM	#293
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Project#2 67-72 Restoration's Shop truck Thanks, will have a lot more still to do on the truck after the meet. Bed wood, new door window seals, new (nice used) door guts, the c-notch and accuair system,....... And down the road I really want to do an ls swap. Posted via Mobile Device __________________ Looking for a 67-72 swb or blazer project in or around VA.



Register or Log In To remove these advertisements.

10-04-2012, 01:55 PM	#294
BMERDOC Registered User Join Date: Jun 2011 Location: Richmond,Va Posts: 2,934	Re: Project#2 67-72 Restoration's Shop truck Sa weet pics of the rear suspension! I'll be bringing most of the tools back and all the brake fluid I can carry. Need anything else? __________________ Nick Carter 1967 C10 Short bed Fleetside Project Cheap Thrills! 2WD C10 Modern/Performance Alignments Easiest Alignment Ever!

10-04-2012, 02:17 PM	#295
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Project#2 67-72 Restoration's Shop truck Need a 1 1/8" socket but I think I will pick one up to have...if you can bring a better 1/2" drive ratchet than the one I have so I can tighten up everything in the rear that would be great. Posted via Mobile Device __________________ Looking for a 67-72 swb or blazer project in or around VA.

10-04-2012, 03:07 PM	#296
Xeen Registered User Join Date: Aug 2012 Location: Topeka Kansas Posts: 2,655	Re: Project#2 67-72 Restoration's Shop truck I had to buy a Craftsman 3/4" breaker bar and 1-1/8", 1-1/16", 3/4" sockets to remove some of the nuts on the rear end of my truck because I broke three craftsman 1/2" Ratchet Drivers and a 1/2" breaker bar before I realized I needed a 3/4" breaker bar LOL __________________ Please call me Brian. Check out My 1972 SWB Fleetside 5.3L Vortec Restomod Build

10-04-2012, 04:16 PM	#297
CC69Rat Registered User Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,209	Re: Project#2 67-72 Restoration's Shop truck Nothing like a tight rear .. __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

10-05-2012, 01:00 AM	#298
NewType72 Registered User Join Date: Feb 2012 Location: turlock Posts: 2,177	Re: Project#2 67-72 Restoration's Shop truck Best comment on the build so far ^ __________________ Project NewType 1972 Chevy C/10 Cheyenne Super ( Daily Driven Showtruck ) http://67-72chevytrucks.com/vboard/s...d.php?t=507903 Project Great Grandpa's Legacy 1973 Chevy C/10 Cheyenne ( Current daily driver collecting big time parts ) http://67-72chevytrucks.com/vboard/s...89#post7084289 - Dylan (209)-985-7721

10-05-2012, 01:05 AM	#299
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Project#2 67-72 Restoration's Shop truck Engine and trans are IN! Despite a few bolts that didn't want to cooperate we got them mounted up. Bmerdoc also helped me button up the steering so now all that needs is the pump and lines ran...(and the wheel ) HUGE thanks to Nick (bmerdoc) for coming by again after work and staying late. Remember guys, he's working on getting his truck ready for our upcoming meet also! Stil have to tighten the tubular crossmember bolts and install the torque converter to flywheel bolts but a BIG step forward tonight. Hoping I can get everything else buttoned up so Sunday Sunday Sunday we can fire it up! Posted via Mobile Device __________________ Looking for a 67-72 swb or blazer project in or around VA.

10-05-2012, 01:08 AM	#300
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Project#2 67-72 Restoration's Shop truck Posted via Mobile Device Attached Images __________________ Looking for a 67-72 swb or blazer project in or around VA.

Register or Log In To remove these advertisements.