![]() |
|
![]() |
#1 |
Senior Member
![]() Join Date: Jul 2012
Location: Oblong, Illinois
Posts: 7,028
|
Re: 48 Burb, bagged, 5.3, 20 year wait
So I was trolling the 60 - 66 Suburban section and another member posted this 62 Suburban below. Turns out it is 40 miles from me and at an auction house. My AAADD (adult automotive attention deficit disorder) kicked in and I had to call. It went through the auction, didn't bring enough, owner went to Florida and is in poor health and asked auction house to sell it...asking $8,000 make an offer.
I couldn't resist and had to go check it out...might be a great deal. And actually it looked pretty good until I looked underneath Pretty rusty with some bad repair attempts....figured there was more of same down low under the nice paint. Darn rust belt....was hoping it had been imported in from a better climate. |
![]() |
![]() |
![]() |
#2 |
Senior Member
![]() Join Date: Jul 2012
Location: Oblong, Illinois
Posts: 7,028
|
Re: 48 Burb, bagged, 5.3, 20 year wait
Guys,
Thanks for all the input for the differential cover. R46 I liked the chopped pyramid idea and spent some time determining material sizes and angles I would need. And I looked at trailer fenders ordering this one... ![]() 16 gauge with radiused edges. Cut the fender down to the right length and made some sides to close it to the floor then welded them in. |
![]() |
![]() |
![]() |
#3 |
Senior Member
![]() Join Date: Jul 2012
Location: Oblong, Illinois
Posts: 7,028
|
Re: 48 Burb, bagged, 5.3, 20 year wait
Rather than direct weld it to the floor, I used 16 gauge bent 90 degrees to position the hump and provide some additional support front to rear.
A little more trimming then will plug weld it together. Think the radius and the hump follows the form of the wheel tubs. |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Jun 2009
Location: Atlanta, Ga.
Posts: 1,104
|
Re: 48 Burb, bagged, 5.3, 20 year wait
AD - nicely done, however, give the pyramid idea a chance as I think it will address the area better. But that's just my opinion.
Try it in cardboard as a sample ... R46 |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jan 2010
Location: Titusville, PA
Posts: 3,585
|
Re: 48 Burb, bagged, 5.3, 20 year wait
looks great
__________________
51' 99toLife finished 2011,355 sbc,5speed, patina, redoing whole truck, inter, bags, etc http://67-72chevytrucks.com/vboard/s...d.php?t=382481 49Hardtimes s/10 susp- bagged, vortec sbc, 5 speed, patina, sold http://67-72chevytrucks.com/vboard/s...d.php?t=594874 VIDEOS https://youtu.be/E8zHhjgS_lA https://youtu.be/E8zHhjgS_lA Geronimo 54' LS engine, static drop IFS, Client build, just about done http://67-72chevytrucks.com/vboard/s...62#post7399162 52' 3100 Slowly in progress, will be painted two toned, have 235 with a t-5, lowered OG frame Other projects, 49' farmuse 3100, killer Patina, will be slammed, LS engine, full done interior up next! www.coffeeandcustoms.com |
![]() |
![]() |
![]() |
#6 |
Senior Member
![]() Join Date: Mar 2011
Location: West Plains, Missouri
Posts: 7,557
|
Re: 48 Burb, bagged, 5.3, 20 year wait
Doug, great job on the cover, I love it...Jim
__________________
my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=459839 Jimbo's long bed step build:http://67-72chevytrucks.com/vboard/s...t=464626<br /> |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Jun 2013
Location: berryville, va
Posts: 129
|
Re: 48 Burb, bagged, 5.3, 20 year wait
Looks great! Like it's supposed to be there.
|
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Nov 2011
Location: West Plains Missouri
Posts: 2,088
|
Re: 48 Burb, bagged, 5.3, 20 year wait
Now your cooking with Gas!!!
![]() Like it alot.. Mark...
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=645774 Project Orangepeel 52 A.D. http://67-72chevytrucks.com/vboard/s...d.php?t=653337 John's LS 49 dodge http://67-72chevytrucks.com/vboard/s...d.php?t=655780 Blake's 67 GMC LS stepside http://67-72chevytrucks.com/vboard/s...d.php?t=690527 Reed 78 FJ40 Rebuild http://67-72chevytrucks.com/vboard/s...d.php?t=733259 Barger's 78 FJ40 |
![]() |
![]() |
![]() |
#9 |
Registered User
![]() Join Date: Mar 2007
Location: Scotts, Michigan
Posts: 3,770
|
Re: 48 Burb, bagged, 5.3, 20 year wait
See we knew that you would figure it out.
It looks good. Marc
__________________
…………...........__________ .................. ((__|__||___\____ ..;.;;.:;:;.,;..;((_(O))____ (_(O)) 1948 Chevy Truck - Finished SOLD!! 1953 Chevy Suburban "Family Truckster" Completed: Spring of 2021 http://67-72chevytrucks.com/vboard/s...d.php?t=605484 1994 4x4 Blazer - "Field Find" https://67-72chevytrucks.com/vboard/...ferrerid=30857 |
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: Jan 2015
Location: Escondido,Ca
Posts: 347
|
Re: 48 Burb, bagged, 5.3, 20 year wait
There you go the covers perfect! Nice job
|
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Jan 2014
Location: Grants New Mexico
Posts: 613
|
Re: 48 Burb, bagged, 5.3, 20 year wait
AD;
![]() you did a great job.looks like the top of the tubs on a smaller scale, Just the way I would have done it all so. Still able to put seats over it if need be. T-P Auto Tim ![]() |
![]() |
![]() |
![]() |
#12 |
Senior Member
![]() Join Date: Jul 2012
Location: Oblong, Illinois
Posts: 7,028
|
Re: 48 Burb, bagged, 5.3, 20 year wait
Hey thanks guys!....appreciate the ideas and direction.
Hmm...now what to do? Ha, plenty of choices |
![]() |
![]() |
![]() |
#13 |
Registered User
Join Date: Jan 2014
Location: New Bloomfield pa.
Posts: 644
|
Re: 48 Burb, bagged, 5.3, 20 year wait
I think I would have brought home the 62
|
![]() |
![]() |
![]() |
#14 |
Senior Member
![]() Join Date: Jul 2012
Location: Oblong, Illinois
Posts: 7,028
|
Re: 48 Burb, bagged, 5.3, 20 year wait
Iceburgh I thought seriously about it...and I have 2 projects now and really don't need another.
![]() A little progress...welded in the differential hump then kinda stood back and enjoyed the look of the floor. Not bad looking and a lotta work to get there. It was nice to pick up some wrenches to finish stripping the dash. The flat floor was pretty comfortable for working under the dash too. The radio opening is hacked up and I am going to wait to fix that until I figure out what to do for a radio. Apparently I'm not into tunes as I've never put any sound system in any vehicle I've ever built. May not on this one either...dunno yet. Thanks for checking in on the build. |
![]() |
![]() |
![]() |
#15 |
Registered User
![]() Join Date: Mar 2007
Location: Scotts, Michigan
Posts: 3,770
|
Re: 48 Burb, bagged, 5.3, 20 year wait
AD-
I can see why you are admiring that floor. You did a bang up job on it. Remind me did you use 16g or 18g for the rear floor? This is looking better all the time. Marc
__________________
…………...........__________ .................. ((__|__||___\____ ..;.;;.:;:;.,;..;((_(O))____ (_(O)) 1948 Chevy Truck - Finished SOLD!! 1953 Chevy Suburban "Family Truckster" Completed: Spring of 2021 http://67-72chevytrucks.com/vboard/s...d.php?t=605484 1994 4x4 Blazer - "Field Find" https://67-72chevytrucks.com/vboard/...ferrerid=30857 |
![]() |
![]() |
![]() |
#16 |
Senior Member
![]() Join Date: Jul 2012
Location: Oblong, Illinois
Posts: 7,028
|
Re: 48 Burb, bagged, 5.3, 20 year wait
Thanks Marc!
I used 16 gauge. Believe most floors are built with 18 gauge though they use beading / ribbing for additional strength. This one might have been overkill and it feels pretty solid. There is one area of oil canning near the rear I will need to address. If there is any way I can help you with yours please let me know. |
![]() |
![]() |
![]() |
#17 | |
Registered User
![]() Join Date: Mar 2007
Location: Scotts, Michigan
Posts: 3,770
|
Re: 48 Burb, bagged, 5.3, 20 year wait
Quote:
I appreciate your offer. Once I figure out a plan I will let you know. Marc
__________________
…………...........__________ .................. ((__|__||___\____ ..;.;;.:;:;.,;..;((_(O))____ (_(O)) 1948 Chevy Truck - Finished SOLD!! 1953 Chevy Suburban "Family Truckster" Completed: Spring of 2021 http://67-72chevytrucks.com/vboard/s...d.php?t=605484 1994 4x4 Blazer - "Field Find" https://67-72chevytrucks.com/vboard/...ferrerid=30857 |
|
![]() |
![]() |
![]() |
#18 |
SAVING ONE TRUCK AT A TIME
![]() Join Date: Feb 2010
Location: sherwood oregon
Posts: 1,141
|
Re: 48 Burb, bagged, 5.3, 20 year wait
Thanks for checking in on my build. Your burb brings back great memories of working on mine. Really diggin the work you are doing. Floors look great.
__________________
53-suburban (99% done) 40-pick up (99.9% done) 12-cc lb dually D-max (dd) 61-crew cab D-max "PAY LESS FOR WHAT YOU NEED PAY MORE FOR WHAT YOU WANT" 53 BURBAN BARN FIND:http://67-72chevytrucks.com/vboard/s...d.php?t=404091 1940 PROJECT MOON SHINE:http://67-72chevytrucks.com/vboard/s...d.php?t=551088 1961 CREW MAX: http://67-72chevytrucks.com/vboard/s....php?p=6957999 |
![]() |
![]() |
![]() |
#19 | |||
Senior Member
![]() Join Date: Jul 2012
Location: Oblong, Illinois
Posts: 7,028
|
Re: 48 Burb, bagged, 5.3, 20 year wait
Quote:
Thank you Jim. Always appreciate your encouragement. Really glad to see you in the shop some with the updates on your 50. That is an awesome truck! Quote:
Quote:
Guys, thanks for the pats on the back. |
|||
![]() |
![]() |
![]() |
#20 |
Registered User
Join Date: Feb 2014
Location: Indiana
Posts: 40
|
Re: 48 Burb, bagged, 5.3, 20 year wait
AD, you have a very NICE project. VERY well documented with pictures and explanations. I'm kinda new to this jumbo truck forum, and fascinated with all the cool projects and talented people.
I'm curious about your toeboard clearance, to clear a 4L65E. I'm kind of on hold with my project, for the same reason. Some say it will fit without any cutting, but I'm doubtful. Also, I'm relatively close to you, over in west-central Indiana. I've been wanting to go over and visit the guy you speak so highly of, Trick Trucks and Rods over in Ohio. He advertises in our Indiana Auto & RV all the time. Looks like a cool place.
__________________
Steve. 1950 Chevy, 3100, built in Norwood Ohio, USA. My build thread, http://talk.classicparts.com/showthread.php?t=19110 |
![]() |
![]() |
![]() |
#21 | |
Senior Member
![]() Join Date: Jul 2012
Location: Oblong, Illinois
Posts: 7,028
|
Re: 48 Burb, bagged, 5.3, 20 year wait
Quote:
Yeah I have lots of pictures and a lotta yackity yack..hrpt, car events, grandkids, other projects...just the car life we live and have fun with. And welcome to the forum. Don't be shy about sharing your build...we all learn from each other. |
|
![]() |
![]() |
![]() |
#22 |
Senior Member
![]() Join Date: Mar 2011
Location: West Plains, Missouri
Posts: 7,557
|
Re: 48 Burb, bagged, 5.3, 20 year wait
Sweet looking view, both from front and rear...Jim
__________________
my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=459839 Jimbo's long bed step build:http://67-72chevytrucks.com/vboard/s...t=464626<br /> |
![]() |
![]() |
![]() |
#23 |
Registered User
Join Date: Jan 2010
Location: Titusville, PA
Posts: 3,585
|
Re: 48 Burb, bagged, 5.3, 20 year wait
too bad all that hard work gets covered up! I hate when people hack up the radio spot. A. delete plates aren't cheap and b. if there is any damage in that area it is hard to fix been there done that. I hope you find a way to incorporate the delete plate if you go no radio (which I'm not a huge fan of them either) I have one in my 51' and its hidden, I never use it. Will be putting one in my current build but it will be hidden also. I just rock the delete plates, that area shaved is just too much blank space for me.
__________________
51' 99toLife finished 2011,355 sbc,5speed, patina, redoing whole truck, inter, bags, etc http://67-72chevytrucks.com/vboard/s...d.php?t=382481 49Hardtimes s/10 susp- bagged, vortec sbc, 5 speed, patina, sold http://67-72chevytrucks.com/vboard/s...d.php?t=594874 VIDEOS https://youtu.be/E8zHhjgS_lA https://youtu.be/E8zHhjgS_lA Geronimo 54' LS engine, static drop IFS, Client build, just about done http://67-72chevytrucks.com/vboard/s...62#post7399162 52' 3100 Slowly in progress, will be painted two toned, have 235 with a t-5, lowered OG frame Other projects, 49' farmuse 3100, killer Patina, will be slammed, LS engine, full done interior up next! www.coffeeandcustoms.com |
![]() |
![]() |
![]() |
#24 |
Registered User
Join Date: Dec 2014
Location: Longview, TX
Posts: 23
|
Re: 48 Burb, bagged, 5.3, 20 year wait
Nice work. Skimmed through it. I'll go back and read it all when I get a chance though!
|
![]() |
![]() |
![]() |
#25 |
Senior Member
![]() Join Date: Jul 2012
Location: Oblong, Illinois
Posts: 7,028
|
Re: 48 Burb, bagged, 5.3, 20 year wait
Thanks Cody! Lotta yackity yack in this thread like I've mentioned and pretty basic build stuff....nothing cool like yours. Looking forward to your build updates!
|
![]() |
![]() |
![]() |
Bookmarks |
|
|