Project NOT4SLE - Page 13 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

*vegaschevy* · 01-15-2010, 08:48 AM

I wanted to add a muffler to the truck as I chopped the exhaust off when I lowered it.
Got a flowmaster from a buddy he had laying around and got her fabbed up. It is fabbed in a way that you would be scared to know who did it. LOL but it will work till I finalize building a small block, big block, LS motor for the truck. So many freaking ideas, and so little money to fund them all. HAHAHAHA

not to mention I wanted to double check nuts and bolts

For ease of not doing an LS install it would be obvious to swap in a 383 stroker as it will drop right in with minimal changes. the big block will take a little more, and an LS motor even more.

So what do you think about this small block idea???

Tagg33 · 01-15-2010, 10:52 AM

I love the twin turbo idea, I've been kicking that idea around for awhile now. My money has to get other things done on the truck first. But someday I hope to hang a couple hair dryers like that.

ripdog28 · 01-15-2010, 12:46 PM

If i had a twin turbo SBC in my garage, it would not take long to install.

*highperf4x4* · 01-15-2010, 05:32 PM

I'll tell you what I think, I think you're going to need some meats on the rear.

nuke1 · 01-15-2010, 10:57 PM

I LOVE THE IDEA!!!!! two huffers, oh yeah, nothin better than the sound of a tubo spooling up getting ready to lay down some serious pwer!

*vegaschevy* · 01-20-2010, 08:58 PM

Got home from work today, through the truck up on jackstands and decided to get to work on getting the front end done.
I think cleaning and refurbishing the parts not being replaced will take longer then anything else. A lot of dirt, rock, concrete type stuff on it all over. LOL

I am hoping to be done by Friday.

VA72C10 · 01-20-2010, 11:51 PM

Progress!!!!

Looking good and dirty...will be a nice improvement not only to the stance but getting all that cleaned up!!!

*highperf4x4* · 01-21-2010, 12:13 AM

Ok, sounds good.

Hey, the grooves in them rotors are supposed to be there!

*vegaschevy* · 01-21-2010, 08:12 AM

Quote:

Originally Posted by highperf4x4

Ok, sounds good.

Hey, the grooves in them rotors are supposed to be there!

I think just getting all the caked on mud stuff off will be a world of difference, not to mention getting new steering components

*highperf4x4* · 01-21-2010, 01:24 PM

Right on! Are you planning on shooting any paint on the frame after things are cleaned up or is that in the future.

*vegaschevy* · 01-21-2010, 02:19 PM

Quote:

Originally Posted by highperf4x4

Right on! Are you planning on shooting any paint on the frame after things are cleaned up or is that in the future.

Ya, Im going to try and something. Luckily out here we dont have rust problems but I want it to look a little better lol.

Im looking for a rolling chassis that I can powdercoat but I lost out on one a few weeks ago by an hour... grr

Smallz72project · 01-21-2010, 04:23 PM

Truck is coming along nicely!! Keep it up. Not gunna lie Im a bit jealous cause Im no where close to even dreaming of being at the point you are. Keep on Truckin!

squareshane33 · 01-21-2010, 04:31 PM

Love the build man, like the fact that you plan on it being a daily driver. Keep rockin, and can't wait to see the front suspension done.

*vegaschevy* · 01-21-2010, 07:43 PM

A few quick pictures of the res of the truck. Finished taking it all apart. Started oven cleaning and pressure washing all the control arms and I found out I need a bead blaster lol

The drivers side upper ball joint was still riveted to the control arm so it was an original.

VA72C10 · 01-21-2010, 08:33 PM

Looks like good progress...I remember the dirty stage on mine

do I spy bonnie???

oldblue1968chevy · 01-21-2010, 11:24 PM

looks good but why dont u pull clip and do the whole frontend?

lookin killer cant wait to see front droped!

*highperf4x4* · 01-22-2010, 12:06 AM

I think he has to keep it together to drive it.

At least the control arms can be taken somewhere and blasted easy enough.

*vegaschevy* · 01-22-2010, 01:00 AM

Quote:

Originally Posted by oldblue1968chevy

looks good but why dont u pull clip and do the whole frontend?

lookin killer cant wait to see front droped!

I actually am installing 67 fenders, 67 grill and a cowl hood in about a month or two. Once my rims and tires are on it. So It will be coming apart for that install and Ill finish the frame then.

Quote:

Originally Posted by highperf4x4

I think he has to keep it together to drive it.

At least the control arms can be taken somewhere and blasted easy enough.

I actually picked up a bead blaster and picked up some stuff and will be installing it in the garage tomorrow. Ill bead blast my own arms LOL

Smallz72project · 01-22-2010, 01:34 AM

Looking good! Dont you love all the work we have to do to just prep something to go back together!

But I guess thats what gives us the pride and joy of having these trucks and knowing we know every square inch of them. Tell Bonnie to get her cluckin bum off the wheel and help you clean up some. She may be a guest but nothing comes free now adays.

gcburdic · 01-22-2010, 09:41 AM

Sweet progress....I see Bonni supervised this work!!!

*highperf4x4* · 01-22-2010, 01:07 PM

Dude, there is a rubber chicken sitting on your wheel...................

*vegaschevy* · 01-22-2010, 04:00 PM

Quote:

Originally Posted by highperf4x4

Dude, there is a rubber chicken sitting on your wheel...................

and by the mirror in a couple of pics!!

*highperf4x4* · 01-22-2010, 08:02 PM

Quote:

Originally Posted by vegaschevy

and by the mirror in a couple of pics!!

Things that make you go hmmmmmmmmmm

G-Ring · 01-24-2010, 12:35 PM

Dude drop me a line if you work that susp on the weekend. I'm on the m-f grind currently but planning to start my SB this spring and could use a refresher...still want to check out that rear susp too. Have you found any good chrome platers in town?

C20-67_N_MO · 01-24-2010, 03:40 PM

WOW!

I just read your entire build thread and it's really taken shape!

Keep up the good work!

01-15-2010, 08:48 AM	#301
vegaschevy Account Suspended Join Date: May 2009 Location: las vegas nv Posts: 1,493	Re: Project NOT4SLE I wanted to add a muffler to the truck as I chopped the exhaust off when I lowered it. Got a flowmaster from a buddy he had laying around and got her fabbed up. It is fabbed in a way that you would be scared to know who did it. LOL but it will work till I finalize building a small block, big block, LS motor for the truck. So many freaking ideas, and so little money to fund them all. HAHAHAHA not to mention I wanted to double check nuts and bolts For ease of not doing an LS install it would be obvious to swap in a 383 stroker as it will drop right in with minimal changes. the big block will take a little more, and an LS motor even more. So what do you think about this small block idea??? Last edited by vegaschevy; 02-04-2010 at 12:36 AM.

01-15-2010, 10:52 AM	#302
Tagg33 Registered User Join Date: Mar 2007 Location: Denver, CO Posts: 247	Re: Project NOT4SLE I love the twin turbo idea, I've been kicking that idea around for awhile now. My money has to get other things done on the truck first. But someday I hope to hang a couple hair dryers like that. __________________ Ryan 84 SWB, C4 IFS Crossmember, C4 IRS, RE7 bags, WCC 3pc 22"s My reBuild: http://67-72chevytrucks.com/vboard/s...d.php?t=346328

01-15-2010, 12:46 PM	#303
ripdog28 Registered User Join Date: Apr 2008 Location: Imperial Beach, CA Posts: 1,040	Re: Project NOT4SLE If i had a twin turbo SBC in my garage, it would not take long to install. __________________ 69 c-10 BBC 462ci, forged crank, H-beam rods, 10.5-1 KB forged pistons, Dart Iron Eagle 308cc, Straub Cam, Comp Cams chrome moly full rollers, Weiand Team G, Prosystems 950, TH400/3500 Dalenzie stall, Currie 9+ Detroit Locker w/31spline axles.3.5/6in drop. My Build.

01-15-2010, 05:32 PM	#304
highperf4x4 Account Suspended Join Date: Apr 2009 Location: Oklahoma City Posts: 4,709	Re: Project NOT4SLE I'll tell you what I think, I think you're going to need some meats on the rear.

01-15-2010, 10:57 PM	#305
nuke1 Registered User Join Date: Jun 2007 Location: Saskatoon, Saskatchewan,: Posts: 2,901	Re: Project NOT4SLE I LOVE THE IDEA!!!!! two huffers, oh yeah, nothin better than the sound of a tubo spooling up getting ready to lay down some serious pwer! __________________ James 1968 GMC "HAVOC" 1986 GMC "Frank" J.J.R.H. Design & Consulting My 68`Rebuild "HAVOC": http://67-72chevytrucks.com/vboard/s...d.php?t=316300 A 58' chev build thread: http://www.67-72chevytrucks.com/vboa...d.php?t=311238 1969 Camaro Pro Touring http://67-72chevytrucks.com/vboard/s...61#post3513361 Swiss Cheese: http://67-72chevytrucks.com/vboard/s...d.php?t=384390 Adjustable Trailing Arm How-To: http://67-72chevytrucks.com/vboard/s...d.php?t=321100 1968 Ford Farm Truck: http://67-72chevytrucks.com/vboard/s...=1#post6555587

01-20-2010, 08:58 PM	#306
vegaschevy Account Suspended Join Date: May 2009 Location: las vegas nv Posts: 1,493	Re: Project NOT4SLE Got home from work today, through the truck up on jackstands and decided to get to work on getting the front end done. I think cleaning and refurbishing the parts not being replaced will take longer then anything else. A lot of dirt, rock, concrete type stuff on it all over. LOL I am hoping to be done by Friday. Last edited by vegaschevy; 01-20-2010 at 09:00 PM.

01-20-2010, 11:51 PM	#307
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,267	Re: Project NOT4SLE Progress!!!! Looking good and dirty...will be a nice improvement not only to the stance but getting all that cleaned up!!! __________________ Looking for a 67-72 swb or blazer project in or around VA.

01-21-2010, 12:13 AM	#308
highperf4x4 Account Suspended Join Date: Apr 2009 Location: Oklahoma City Posts: 4,709	Re: Project NOT4SLE Ok, sounds good. Hey, the grooves in them rotors are supposed to be there!

01-21-2010, 01:24 PM	#310
highperf4x4 Account Suspended Join Date: Apr 2009 Location: Oklahoma City Posts: 4,709	Re: Project NOT4SLE Right on! Are you planning on shooting any paint on the frame after things are cleaned up or is that in the future.

01-21-2010, 04:23 PM	#312
Smallz72project Registered User Join Date: May 2005 Location: Missoula, MT Posts: 273	Re: Project NOT4SLE Truck is coming along nicely!! Keep it up. Not gunna lie Im a bit jealous cause Im no where close to even dreaming of being at the point you are. Keep on Truckin! __________________ - 1967 Chevy C10 shortbox - 1984 Chevy K10 "Mater"- SWB 305 manual, retired sheriffs truck, Current Frame Off Project - 1986 Chevy K10 LWB 350/350 Daily Driver/project

01-21-2010, 04:31 PM	#313
squareshane33 Registered User Join Date: Oct 2009 Location: Tulsa, OK Posts: 30	Re: Project NOT4SLE Love the build man, like the fact that you plan on it being a daily driver. Keep rockin, and can't wait to see the front suspension done. __________________ *SquareShane33* 1987 SWB (Future Project) 1958 BBW Short Bed Fleetside 1978 SWB (RIP)

01-21-2010, 07:43 PM	#314
vegaschevy Account Suspended Join Date: May 2009 Location: las vegas nv Posts: 1,493	Re: Project NOT4SLE A few quick pictures of the res of the truck. Finished taking it all apart. Started oven cleaning and pressure washing all the control arms and I found out I need a bead blaster lol The drivers side upper ball joint was still riveted to the control arm so it was an original. Last edited by vegaschevy; 01-21-2010 at 07:46 PM.

01-21-2010, 08:33 PM	#315
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,267	Re: Project NOT4SLE Looks like good progress...I remember the dirty stage on mine do I spy bonnie??? __________________ Looking for a 67-72 swb or blazer project in or around VA.

01-21-2010, 11:24 PM	#316
oldblue1968chevy Grandpa in the rustmobile... Join Date: Nov 2008 Location: Spokane WA/Viola TN Posts: 11,422	Re: Project NOT4SLE looks good but why dont u pull clip and do the whole frontend? lookin killer cant wait to see front droped! __________________ John Goose-1968 C10 355,9.32-1CR, Vortec Heads ,262 voodoo, 3.73:1 3OTT (HS ride/beater/farm truck) http://67-72chevytrucks.com/vboard/s...d.php?t=317684 Grams 53-1953 Chevrolet Belair http://67-72chevytrucks.com/vboard/s...=1#post4327784 1969 Chevy C10 Shortbed 4.5/6?" Frame off resto http://67-72chevytrucks.com/vboard/s...d.php?t=548136 1999 Toyota Tacoma 4x4

01-22-2010, 12:06 AM	#317
highperf4x4 Account Suspended Join Date: Apr 2009 Location: Oklahoma City Posts: 4,709	Re: Project NOT4SLE I think he has to keep it together to drive it. At least the control arms can be taken somewhere and blasted easy enough.



Register or Log In To remove these advertisements.

01-22-2010, 01:34 AM	#319
Smallz72project Registered User Join Date: May 2005 Location: Missoula, MT Posts: 273	Re: Project NOT4SLE Looking good! Dont you love all the work we have to do to just prep something to go back together! But I guess thats what gives us the pride and joy of having these trucks and knowing we know every square inch of them. Tell Bonnie to get her cluckin bum off the wheel and help you clean up some. She may be a guest but nothing comes free now adays. __________________ - 1967 Chevy C10 shortbox - 1984 Chevy K10 "Mater"- SWB 305 manual, retired sheriffs truck, Current Frame Off Project - 1986 Chevy K10 LWB 350/350 Daily Driver/project

01-22-2010, 09:41 AM	#320
gcburdic Restoration Virgin! Join Date: Jan 2008 Location: Huntersville, NC Posts: 8,298	Re: Project NOT4SLE Sweet progress....I see Bonni supervised this work!!! __________________ Geoff with a G 1968 Chevy C10 SWB The Mistress 1972 Custom Deluxe C20 Suburban A Suburban Named Isabella 1966 Ford Mustang Mama's High School Graduation Present

01-22-2010, 01:07 PM	#321
highperf4x4 Account Suspended Join Date: Apr 2009 Location: Oklahoma City Posts: 4,709	Re: Project NOT4SLE Dude, there is a rubber chicken sitting on your wheel...................

01-24-2010, 12:35 PM	#324
G-Ring Registered User Join Date: Apr 2008 Location: las vegas, nv Posts: 21	Re: Project NOT4SLE Dude drop me a line if you work that susp on the weekend. I'm on the m-f grind currently but planning to start my SB this spring and could use a refresher...still want to check out that rear susp too. Have you found any good chrome platers in town? __________________ 79' Big Ten 70' 1 ton 4x4 LB "Mean Green" 70' SWB "Major Project" 69' El Camino "t-boned by Camry"

01-24-2010, 03:40 PM	#325
C20-67_N_MO Champagne Taste on Beer Budget Join Date: Dec 2008 Location: High Ridge, Missouri Posts: 2,190	Re: Project NOT4SLE WOW! I just read your entire build thread and it's really taken shape! Keep up the good work! __________________ Coming Soon: Project 1970 Country Truck

Register or Log In To remove these advertisements.