71' (gonna be) a one of a kind custom

[71' Custom]

Originally Posted by BigDaddyV

Those turned out killer!

Thanks! I can not wait to get some rubber on them now!

[71' Custom]

So not much going on lately, was cleaning up in the garage getting ready for the next part....... the drive train!!! Be looking out for progress after the New Year
Thought I would snap a quick picture for my buddies!

[71' Custom]

So had to jump on this deal a little earlier than I wanted to. But it was on sale for Black Friday from Summit so I just had to go for it!





I had heard horror stories about these blocks, however, aside from the tiniest amount of surface rust around the holes for the head bolts, this is a great block! 880 casting, clearances for a 383, factory roller, 4.030 bore, and a 4 bolt main! This thing will rock!

[71' Custom]

The first meet between engine and frame.....

[BigDaddyV]

Very nice!!!!!

[71' Custom]

Originally Posted by BigDaddyV

Very nice!!!!!

Thanks, getting excited for the next part. Which will be the rotating assembly. Here are the specs:
Brand:SCAT Engine Components
Manufacturer's Part Number:1-40410BI
Part Type:Engine Rotating Kits
Product Line:Scat Engine Rotating Assemblies
Summit Racing Part Number:SCA-1-40410BI

Actual Engine CID:364
Bore (in):4.030 in.
Bore (mm):102.362mm
Engine Stroke (in):3.562 in.
Balanced:Yes
Pistons Included:Yes
Piston Rings Included:Yes
Piston and Ring Oversize (in):0.030 in.
Piston Material:Forged aluminum
Piston Style:Flat top, with two valve reliefs
Piston Head Volume (cc):+5.00cc
Wrist Pin Style:Floating
Piston Ring Facing Material:Plasmamoly
Crankshaft Included:Yes
Crankshaft Material:Forged 4340 steel
Rear Main Seal Style:2-piece
Engine Balance:Internal
Connecting Rods Included:Yes
Connecting Rod Material:Forged 4340 steel
Connecting Rod Beam Style:H-beam

This is Scat brand and I had heard from friends who claim they know someone that had a Scat crankshaft grenade their engine or something. But I have friends, that I know directly, that have used Scat's forged 4340 crankshaft on boosted and nos'd motors without issue. So I am going to give them a shot.

[Orangetonicclicc]

Did you use those CPP tubular mounts? I have those same ones. I had to do the same thing and drill a hole and move my motor back. My headers were hitting the frame. I have headman headers shorties. I cleared it on my frame on the passenger side, but I'm still catching the inner part of my frame on the driver side. I decided to notch my frame ever so slightly. As for the firewall. I had room to spare. Nice tight and clean. I love the look of your truck. We are polar opposites tho. You don't do chrome and I do! Lol! Didn't want to ruin your build with all that bling to show you the outcome of the mounts. But you can go to my last thread and see it. I just did it. So it will be easy to find. Those mounts are really a pain. You will need a certain header to fit so research it. I actually have different header part numbers that will fit those mounts. I just don't know how they will match your other applications? Let me know if you want those header part numbers.

[71' Custom]

Originally Posted by Orangetonicclicc

Did you use those CPP tubular mounts? I have those same ones. I had to do the same thing and drill a hole and move my motor back. My headers were hitting the frame. I have headman headers shorties. I cleared it on my frame on the passenger side, but I'm still catching the inner part of my frame on the driver side. I decided to notch my frame ever so slightly. As for the firewall. I had room to spare. Nice tight and clean. I love the look of your truck. We are polar opposites tho. You don't do chrome and I do! Lol! Didn't want to ruin your build with all that bling to show you the outcome of the mounts. But you can go to my last thread and see it. I just did it. So it will be easy to find. Those mounts are really a pain. You will need a certain header to fit so research it. I actually have different header part numbers that will fit those mounts. I just don't know how they will match your other applications? Let me know if you want those header part numbers.

Just looked/read through your entire build, man you weren't kidding, that's a lot of chrome! Those are the same mounts I am using. I already have a pair of Hooker super comp headers for mine. I will notch the frame if it comes to it. It is good to know that you were able to clear the firewall though. I have been really nervous about that. I would love to see a picture of the space you have between the engine and firewall as well as the space between your belt and your radiator fans. All in all you have a really bad ass truck man, nice build! Can't wait to see more!

[Orangetonicclicc]

Originally Posted by 71' Custom

Just looked/read through your entire build, man you weren't kidding, that's a lot of chrome! Those are the same mounts I am using. I already have a pair of Hooker super comp headers for mine. I will notch the frame if it comes to it. It is good to know that you were able to clear the firewall though. I have been really nervous about that. I would love to see a picture of the space you have between the engine and firewall as well as the space between your belt and your radiator fans. All in all you have a really bad ass truck man, nice build! Can't wait to see more!

Thanks man! I will take a picture and post the firewall and radiator space on my thread for you. The frame is no biggie, I just hope your header clears that mount. That's the big dilemma! I just don't want you to be caught unexpectedly in the middle, like I was. Luckily I was warned early about the mount. The frame was a different story!

[71' Custom]

Rotating assembly should be here by the 22nd of next month. Can't wait, I haven't put a lower end together in years!

[71' Custom]

Ordered a bunch of parts today. Ordered the diff cover, trans pan, oil pan, valve covers, breather, and a few other smaller parts. I know, I know, seems a bit premature, but remember, I have to get these all powder coated in two tone and that takes a while! Pictures to come!

[Hankster]

Frame and engine look good! Can't wait to see it all together.

[71' Custom]

Got almost everything in today

Still waiting on the valve covers
Shipping straight from CalCustoms

[BigDaddyV]

Very nice!

[71' Custom]

Thinking about these now,
These are the valve cover hold down bolts.

Do them black or do them blue? That is the question

[71' Custom]

The engine build had to start somewhere



Very modest beginning. I also gave the block a new paint job. Kinda hard to see from these pictures though.

[71' Custom]

I also moved the engine build into my back living room inside the house. With all the cold and the rain my garage is way too humid to keep in there. I kept getting small spotts of rust.

[71' Custom]

Canceled the order on my CalCustoms valve covers in exchange for these

The CalCustom ones would have taken too long to get, and I really need to get these to powder coat.

[Hankster]

Sweet! I've always loved those valve covers!

[71' Custom]

Originally Posted by Hankster

Sweet! I've always loved those valve covers!

Thanks! I am very happy with them, definately the right choice.
Now back to my diff cover for a moment. This diff covrt is a lot deeper than I had anticipated. The only way I would be able to get the cover on and off would be to unbolt the lower arm on the suspension. And this cover did not have a drain plug. So it was time to make one......

So with that problem solved it was on to the next. The air filter that came with my breather was that maroon K&N volor which was not going to work. So I found one with blue media and a blach screen over it. It looked awesome too, just one problem though, it was thicker than the one it vCard ame with. So i had to trim the inside bottom of the filter to make it fit the lip inside the bottom of the air cleaner. All in all, it came out looking real nice I think.

[71' Custom]

Got everything dropped off at the coater last night, I am sure it will be at least a month before I start getting parts back though. But, my rotating assembly should be showing up any day now!

[CTENTA1]

Is that a "Cool air" filter?

[71' Custom]

Originally Posted by CTENTA1

Is that a "Cool air" filter?

It is a K&N type air filter, it's cleanable/able to be re-oiled. But, it is made by Spectre Performance. I did have a couple of *****es about it though; The filter is thick, so much so that it wouldn't fit in the lip of the breather so I had to cut a notch out of the inside lip of the filter to make it fit, also, it was advertised to be an oval shaped filter. Well, when I opened the box imagine my surprise to find a round filter. It fits, you just have to wrestle it into place and try to get it all together while holding it in the correct shape. But, I do love the way it looks though

[71' Custom]

Contacted Scat today, my crankshaft is being balanced today. Should be shipping either today or Monday!

[71' Custom]

Got in my goodies!!!!!