Daverods project 66 - Page 14 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

joe231 · 07-11-2009, 03:38 PM

Quote:

Originally Posted by daverod

Been out burning around in the new 64. Going alittle further each time. Can't seem to get mt fuel gage working right. When I turn it on it pegs to full. When I turn it off it reads about 1/4. I know it has gas because I just put $20 in it. I'm thinking maybe my sending unit is off?

It seems to be wired right.

check your wire first, sounds like it is either shorted or open...sorry I can never remember which is pegged full

daverod · 07-11-2009, 05:14 PM

Quote:

Originally Posted by joe231

check your wire first, sounds like it is either shorted or open...sorry I can never remember which is pegged full

Thanks Joe I'll check it tonight. I think you 're right.

The 1/4 when turned off was messing with me. Checked the wires with an ohm meter. There not shorted. Ran one wire from the sending unit to the gage and another from the fuse box to the gage; same thing peged. Hooked up the wires to a old dash/gage from my 66; same thing peged. I wishing I still had my 66 gas tank. Never throw anything away. I do like the dash of the 66 better. It has gages insted of lights. Going to see if I can find a sending unit on a old deserted truck I know about.

daverod · 07-12-2009, 10:19 AM

Decided to pull my sending unit before going out to the old truck to look for a new one . Look what I found. Just not sure how to fix it?

Looks to small to weld. I guess it's copper. I've never braised anything and have no idea how. Anyone? What about jb weld?

ruffrida2005 · 07-12-2009, 11:04 AM

JB weld would work, but it's getto. If not cleaned up right you could have it fall off and get stuck. How much is a new sending unit?

joe231 · 07-12-2009, 11:22 AM

I think that is pretty common.
you could probably braze it with a propane torch.

jgh64pkup · 07-12-2009, 12:16 PM

the dropmember looks good

daverod · 07-12-2009, 12:41 PM

Quote:

Originally Posted by ruffrida2005

JB weld would work, but it's getto. If not cleaned up right you could have it fall off and get stuck. How much is a new sending unit?

Checked it out. It is getto, but I'm kinda getto. Trying to clean up my act

. It does'nt conduct electrons.

New unit is $50 plus shipping. $50 saved.

daverod · 07-12-2009, 12:45 PM

Quote:

Originally Posted by joe231

I think that is pretty common.
you could probably braze it with a propane torch.

I did'nt understand what brazen was all about. I have soldered copper pipes before. Cleaned it up and soldered it back together. Works good now still have to mess with bending the rod to get it read right. Thanks Joe.

I think it's within a 1/4 or so.

Time to go burn some gas.

daverod · 07-12-2009, 12:56 PM

I'm going to change this out and put in the 66 dash. I think I can even get a tech for it. Somthing to do when I get bored, I'm kinda bored now.

joe231 · 07-12-2009, 03:19 PM

cool man, brazing and soldering are pretty much the same idea, typically when you solder you use an iron and solder, brazing you use a torch and some type of filler rod.

jgh64pkup · 07-12-2009, 04:29 PM

Quote:

Originally Posted by daverod

Decided to pull my sending unit before going out to the old truck to look for a new one . Look what I found. Just not sure how to fix it?

Looks to small to weld. I guess it's copper. I've never braised anything and have no idea how. Anyone? What about jb weld?

i have one thats brand new you can have but you have to take the gas tank also

daverod · 07-12-2009, 04:37 PM

Quote:

Originally Posted by jgh64pkup

i have one thats brand new you can have but you have to take the gas tank also

I had a tank and threw it away. It's fixed now so I guess it does'nt matter.

Untill my tank starts leaking.

daverod · 07-12-2009, 04:38 PM

Quote:

Originally Posted by jgh64pkup

the dropmember looks good

Thanks It was easy to do.

daverod · 07-12-2009, 04:47 PM

My green temp light comes on when I start up then it goes out after a couple minutes. Is this normal? I'm thinking that maybe it's overheating and the red bulb is burnt out. It doesn't seem hot. Went to swap bulbs did'nt even have a red bulb wrecked the green one getting it out. Guess I'm off to get some bulbs.

jgh64pkup · 07-12-2009, 04:51 PM

Quote:

Originally Posted by daverod

I had a tank and threw it away. It's fixed now so I guess it does'nt matter.

Untill my tank starts leaking.

so you fixed the sending unit
i was joking about the tank

daverod · 07-12-2009, 05:53 PM

Quote:

Originally Posted by jgh64pkup

so you fixed the sending unit
i was joking about the tank

Ya I soldered it back together works good so far.

protrash64 · 07-13-2009, 12:56 AM

Quote:

Originally Posted by daverod

My green temp light comes on when I start up then it goes out after a couple minutes. Is this normal? I'm thinking that maybe it's overheating and the red bulb is burnt out. It doesn't seem hot. Went to swap bulbs did'nt even have a red bulb wrecked the green one getting it out. Guess I'm off to get some bulbs.

Thats the COLD lite!!! The original sender had 2 readings. Cold when you start and then operating temp. If it overheats it turns red.

daverod · 07-13-2009, 09:10 AM

Quote:

Originally Posted by protrash64

Thats the COLD lite!!! The original sender had 2 readings. Cold when you start and then operating temp. If it overheats it turns red.

I was worried because it goes out after awhile but I guess thats normal.

Good thing I checked because it did'nt have a bulb in the red light.

daverod · 07-13-2009, 05:42 PM

Cleaned 50 years of crap off my A arms and cross member. Lowered the arms down and cut 1 1/2 coils off. Putting on some new pads and lines while I'm at it. Can't wait to put the wheels back on.

Put a new bulb in my red and green warning light now nothing works.

Have to mess with it some more. Habor freight jack stands $19 for 2. There going fast get some now.

My truck looks like a stink bug.

daverod · 07-13-2009, 09:19 PM

Messed with my temp lights some more. If I take the red light bulb out then the green light works. If I put the red bulb in nothing works. There all new bulbs. Maybe a short? Maybe a bad temp senser? Now I know why it did'nt have a red bulb.

http://picasaweb.google.com/normanme...eat=directlink I think I need the next page.

ruffrida2005 · 07-13-2009, 10:08 PM

sounds like you have a bad ground on the lights.

daverod · 07-13-2009, 10:17 PM

Quote:

Originally Posted by ruffrida2005

sounds like you have a bad ground on the lights.

Well, the green light works? Except when the red bulb is pluged in. If I take the red bulb out the green works.

Turned out the Temp. sending unit? going into the radiator hose is messed up. When I move the wires going into things change ( one light, no lights, both lights). Can't seem to find one in LMC.

daverod · 07-14-2009, 09:19 AM

Anybody know what the thing with the wires going into it is called and where I can get a new one?

It goes to the temp. warning lights on a 64.

**Captainfab** · 07-15-2009, 12:36 AM

Ordinarily a temperature sending unit has only one wire. Looks like that one has 2 or 3 wires? I don't know what else it would be being it is in the coolant.

daverod · 07-15-2009, 08:52 AM

It has 2 wires and it looks like it goes in the coolant. When I wiggle it it makes my temp warning lights (green/red) blink on and off. I think it's bad and I need a new one.

07-12-2009, 10:19 AM	#328
daverod SSN 706 Join Date: Mar 2009 Location: Pocatello Idaho Posts: 3,821	Re: Daverods project 66 Decided to pull my sending unit before going out to the old truck to look for a new one . Look what I found. Just not sure how to fix it? Looks to small to weld. I guess it's copper. I've never braised anything and have no idea how. Anyone? What about jb weld? Attached Images __________________ Daverods 64 C10 Daily driver 292 3 speed "Driver" Daverods 66 Build C10 Bags 350/350(On Hold) Daverods 52 Build 3100 S10 chassis,Bags, 350/700r4 "Click it" Last edited by daverod; 07-12-2009 at 10:33 AM.

07-12-2009, 11:04 AM	#329
ruffrida2005 Member of the longbed union. Join Date: Feb 2009 Location: Killeen, Tx Posts: 2,158	Re: Daverods project 66 JB weld would work, but it's getto. If not cleaned up right you could have it fall off and get stuck. How much is a new sending unit? __________________ Paul 88 GMC Crew Cab dually, 454/T400 64 LWB 400 HP 350/350T Bagged, under construction! Sold most of it! 92 S10 Iron Duke 5 speed, 5/7 drop for now. soon to be bagged. Sold http://67-72chevytrucks.com/vboard/s...59#post4637759

07-12-2009, 11:22 AM	#330
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: Daverods project 66 I think that is pretty common. you could probably braze it with a propane torch. __________________ *CHEVY ONLY*

07-12-2009, 12:16 PM	#331
jgh64pkup Sunburst C10!!! Join Date: Jan 2009 Location: Texas Posts: 2,560	Re: Daverods project 66 the dropmember looks good __________________ Gage 1967 C10 Shortbed Stepside Last edited by jgh64pkup; 07-12-2009 at 01:38 PM.

07-12-2009, 12:56 PM	#334
daverod SSN 706 Join Date: Mar 2009 Location: Pocatello Idaho Posts: 3,821	Re: Daverods project 66 I'm going to change this out and put in the 66 dash. I think I can even get a tech for it. Somthing to do when I get bored, I'm kinda bored now. Attached Images __________________ Daverods 64 C10 Daily driver 292 3 speed "Driver" Daverods 66 Build C10 Bags 350/350(On Hold) Daverods 52 Build 3100 S10 chassis,Bags, 350/700r4 "Click it"

07-12-2009, 03:19 PM	#335
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: Daverods project 66 cool man, brazing and soldering are pretty much the same idea, typically when you solder you use an iron and solder, brazing you use a torch and some type of filler rod. __________________ *CHEVY ONLY*

07-12-2009, 04:47 PM	#339
daverod SSN 706 Join Date: Mar 2009 Location: Pocatello Idaho Posts: 3,821	Re: Daverods project 66 My green temp light comes on when I start up then it goes out after a couple minutes. Is this normal? I'm thinking that maybe it's overheating and the red bulb is burnt out. It doesn't seem hot. Went to swap bulbs did'nt even have a red bulb wrecked the green one getting it out. Guess I'm off to get some bulbs. __________________ Daverods 64 C10 Daily driver 292 3 speed "Driver" Daverods 66 Build C10 Bags 350/350(On Hold) Daverods 52 Build 3100 S10 chassis,Bags, 350/700r4 "Click it" Last edited by daverod; 07-12-2009 at 05:05 PM.

07-13-2009, 05:42 PM	#344
daverod SSN 706 Join Date: Mar 2009 Location: Pocatello Idaho Posts: 3,821	Re: Daverods project 66 Cleaned 50 years of crap off my A arms and cross member. Lowered the arms down and cut 1 1/2 coils off. Putting on some new pads and lines while I'm at it. Can't wait to put the wheels back on. Put a new bulb in my red and green warning light now nothing works. Have to mess with it some more. Habor freight jack stands $19 for 2. There going fast get some now. My truck looks like a stink bug. Attached Images __________________ Daverods 64 C10 Daily driver 292 3 speed "Driver" Daverods 66 Build C10 Bags 350/350(On Hold) Daverods 52 Build 3100 S10 chassis,Bags, 350/700r4 "Click it" Last edited by daverod; 07-13-2009 at 09:13 PM.

07-13-2009, 09:19 PM	#345
daverod SSN 706 Join Date: Mar 2009 Location: Pocatello Idaho Posts: 3,821	Re: Daverods project 66 Messed with my temp lights some more. If I take the red light bulb out then the green light works. If I put the red bulb in nothing works. There all new bulbs. Maybe a short? Maybe a bad temp senser? Now I know why it did'nt have a red bulb.http://picasaweb.google.com/normanme...eat=directlink I think I need the next page. __________________ Daverods 64 C10 Daily driver 292 3 speed "Driver" Daverods 66 Build C10 Bags 350/350(On Hold) Daverods 52 Build 3100 S10 chassis,Bags, 350/700r4 "Click it" Last edited by daverod; 07-13-2009 at 09:25 PM.

07-13-2009, 10:08 PM	#346
ruffrida2005 Member of the longbed union. Join Date: Feb 2009 Location: Killeen, Tx Posts: 2,158	Re: Daverods project 66 sounds like you have a bad ground on the lights. __________________ Paul 88 GMC Crew Cab dually, 454/T400 64 LWB 400 HP 350/350T Bagged, under construction! Sold most of it! 92 S10 Iron Duke 5 speed, 5/7 drop for now. soon to be bagged. Sold http://67-72chevytrucks.com/vboard/s...59#post4637759

07-14-2009, 09:19 AM	#348
daverod SSN 706 Join Date: Mar 2009 Location: Pocatello Idaho Posts: 3,821	Re: Daverods project 66 Anybody know what the thing with the wires going into it is called and where I can get a new one? It goes to the temp. warning lights on a 64. Attached Images __________________ Daverods 64 C10 Daily driver 292 3 speed "Driver" Daverods 66 Build C10 Bags 350/350(On Hold) Daverods 52 Build 3100 S10 chassis,Bags, 350/700r4 "Click it"

07-15-2009, 12:36 AM	#349
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,250	Re: Daverods project 66 Ordinarily a temperature sending unit has only one wire. Looks like that one has 2 or 3 wires? I don't know what else it would be being it is in the coolant. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

07-15-2009, 08:52 AM	#350
daverod SSN 706 Join Date: Mar 2009 Location: Pocatello Idaho Posts: 3,821	Re: Daverods project 66 It has 2 wires and it looks like it goes in the coolant. When I wiggle it it makes my temp warning lights (green/red) blink on and off. I think it's bad and I need a new one. __________________ Daverods 64 C10 Daily driver 292 3 speed "Driver" Daverods 66 Build C10 Bags 350/350(On Hold) Daverods 52 Build 3100 S10 chassis,Bags, 350/700r4 "Click it" Last edited by daverod; 07-15-2009 at 08:52 AM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.