![]() |
![]() |
#351 |
Registered User
Join Date: Nov 2014
Location: somewhere, PA
Posts: 1,074
|
Re: It's my turn, 47 S10 build
are those the final wheels or can you just get something with 2" less backspacing now?
huge props fabbin the whole knuckle like that. |
![]() |
![]() |
![]() |
#352 | |
Registered User
Join Date: Oct 2009
Location: Hoskins nebraska
Posts: 401
|
Re: It's my turn, 47 S10 build
Quote:
Ya, i wasn't excited about running the spacers either. If i would have not built them as drop spindles i think they would have cleared the tie rod. If i upside wheels later i can get rid of them.
__________________
Fast, Cheap, Reliable. You may pick two My 47/S10 build http://67-72chevytrucks.com/vboard/s...d.php?t=679723 |
|
![]() |
![]() |
![]() |
#353 |
Registered User
Join Date: Oct 2009
Location: Hoskins nebraska
Posts: 401
|
Re: It's my turn, 47 S10 build
Yep, keeping the same wheels for now. Down the road I'll probably upsize then. I can get rid of the spacers at that time.
__________________
Fast, Cheap, Reliable. You may pick two My 47/S10 build http://67-72chevytrucks.com/vboard/s...d.php?t=679723 |
![]() |
![]() |
![]() |
#354 |
Registered User
Join Date: Oct 2009
Location: Hoskins nebraska
Posts: 401
|
Re: It's my turn, 47 S10 build
Been really bad about updates but it's slowly moving along. Frame is totally stripped down and mounted on the frame table to keep it square. I blasted the inside of the frame a couple weeks ago and painted everything i could reach with header paint. Where the plan is to powder coat it i wanted something on the inside that's not going to burn off when they bake the powder coat. Next up is boxing the middle of the frame back to the gas tank crossmember. Once that is welded up and solid I'll move on to the back. I have a piece of 1/8" wall rec tubing that will tie the back of the rails together along with being boxed. The stock crossmember with the spare tire hoist is coming out and the hoist is getting relocated. After getting a flat twice on my car that didn't come with a spare in not going through that again. Already measured and a temp spare will fit under there just fine and be out of sight. Plus a little extra rearweight won't hurt.
__________________
Fast, Cheap, Reliable. You may pick two My 47/S10 build http://67-72chevytrucks.com/vboard/s...d.php?t=679723 |
![]() |
![]() |
![]() |
#355 |
Registered User
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,026
|
Re: It's my turn, 47 S10 build
nice.
is the round tubing for bracing or is it part of the build? curious if there will be a lower section to that if it is part of the build. something to use as a trans mount/frame stabilizer in the center section. otherwise it is a long run between cross members. keep posting your progress, get it all done before powder coating or it becomes a mess to do changes, as I am sure you are well aware. |
![]() |
![]() |
![]() |
#356 |
Registered User
Join Date: Oct 2009
Location: Hoskins nebraska
Posts: 401
|
Re: It's my turn, 47 S10 build
The round tubing is for bracing. When i was building the motor mounts i had the jack under the crossmember and jackstands under the frame just in front of the cab mounts. When I lowered the jack i watched the distributor move almost 1/4” away from the firewall just from flex in the front rails. That wasn't going to work for me. All the tubing is 1.5" .125 wall. With an 8pt x brace under there combined boxing the rest of the frame should make it as rigid as I need. The motor is only in the 450hp range and I'm not running it down the strip.
The transmission mount hangs from the ears in the middle. I got lucky and measured right and was able to just flip the mount around when switching from the 700r4 to the 4l80 during the current rebuild. I had about 3000 miles on it to shake everything down so i would be pretty good to go.
__________________
Fast, Cheap, Reliable. You may pick two My 47/S10 build http://67-72chevytrucks.com/vboard/s...d.php?t=679723 |
![]() |
![]() |
![]() |
#357 |
Registered User
Join Date: Nov 2014
Location: somewhere, PA
Posts: 1,074
|
Re: It's my turn, 47 S10 build
that'll be WAY stiffer!
i love how the brake mount and trans mount all worked right into the same crossmember like that. clean. |
![]() |
![]() |
![]() |
Bookmarks |
|
|