What did you do to your truck today.The 3rd chapter - Page 15 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**zicc1835** · 03-11-2019, 11:59 AM

Quote:

Originally Posted by 71CHEVYSHORTBED402

Polished this up with Pro Honda. Comes in a spray. Beyond my expectations, it took out some tuff areas with ease. I could brighten it up some more, but why bother. May have painted it, they look amazing painted, but seems they "breathe" easier without it.

$1550 to have this rebuilt. It's shifted smooth since the day I got it, but 140K miles, and an occasion of abuse

, it was due.

Which one did you use they have a few different products
Thanks

89AKurt · 03-11-2019, 12:53 PM

Not sure if it's worth the trouble, cleaned up the aluminum trim with steel wool. It's all trashed, front fender arch looks like it was driven through a barbed wire fence.

Can anyone tell I did only the cab?

weq92f · 03-11-2019, 01:07 PM

.
Can't tell with that image, no. Too poor quality and the angle is wrong for comparison.

But... it does look good to me!

-klb

BugzC10 · 03-11-2019, 01:40 PM

Quote:

Originally Posted by 89AKurt

Not sure if it's worth the trouble, cleaned up the aluminum trim with steel wool. It's all trashed, front fender arch looks like it was driven through a barbed wire fence.

Can anyone tell I did only the cab?

That's called Patina!

**71CHEVYSHORTBED402** · 03-11-2019, 05:54 PM

Quote:

Originally Posted by zicc1835

Which one did you use they have a few different products
Thanks

Here you go. Their instructions say "for longer lasting shine, leave on until haze and buff"...............Well, I tested an area, let it sit over 24 hours and their aint no haze about it, it's pretty oily. https://www.chapmoto.com/pro-honda-s...EaAssvEALw_wcB

The transmission was mostly clean already. I sprayed a reasonable amount and let it sit 4-5 hours. Wiped, brass brushes on a Dremmel, wiped. Sprayed some more and buffed some with fine steel wool, whiped. Sprayed a pinch more, wiped and done. About 1.5 hours is all, nice stuff.

Barnfind46 · 03-11-2019, 06:41 PM

Every little bit helps. The little things are what make a well kept daily driver stand out. I repainted the tailgate letters on my faded tailgate with a spray can and some tape. Made the truck look much better!

66clow · 03-11-2019, 10:13 PM

Recived my bolt on firewall panels from Atomic Armadillo Metal Fab. Excellent fit.

**zicc1835** · 03-11-2019, 11:10 PM

Quote:

Originally Posted by 71CHEVYSHORTBED402

Here you go. Their instructions say "for longer lasting shine, leave on until haze and buff"...............Well, I tested an area, let it sit over 24 hours and their aint no haze about it, it's pretty oily. https://www.chapmoto.com/pro-honda-s...EaAssvEALw_wcB

The transmission was mostly clean already. I sprayed a reasonable amount and let it sit 4-5 hours. Wiped, brass brushes on a Dremmel, wiped. Sprayed some more and buffed some with fine steel wool, whiped. Sprayed a pinch more, wiped and done. About 1.5 hours is all, nice stuff.

Thanks much for the response I’m going to try it .....my trans is clean I thought about paint but like the natural cast look

**SoCoC10** · 03-11-2019, 11:28 PM

Installed new trim on the K10 Cheyenne. Final door and fender fitment is next.

**71CHEVYSHORTBED402** · 03-12-2019, 01:56 AM

Quote:

Originally Posted by zicc1835

Thanks much for the response I’m going to try it .....my trans is clean I thought about paint but like the natural cast look

I read someplace the transmission will appreciate the natural cast, something to the effect paint may look in some heat. Good enough for GM it's good enough for me. There's a little scaling, you can see. I figure so what.

I shined up and installed the tubes today. 3M works magic on stainless and chrome. The transmission tube was well stained etc., no problem.

Trim look AWESOME SoCoC10

Andy4639 · 03-12-2019, 09:21 AM

I loaded the ramp truck yesterday for the 5hr trip to the beach for the big one in SC.
First show of the season for me.

JustToxic · 03-12-2019, 10:04 AM

Started putting new floor boards in the cab over the weekend. New kick panels, lower A-pillar, DS forward cab support, Inner and outer rockers, PS rear cab support and finally Cab corners.

**Thrill4130** · 03-13-2019, 09:14 PM

Quote:

Originally Posted by 89AKurt

Not sure if it's worth the trouble, cleaned up the aluminum trim with steel wool. It's all trashed, front fender arch looks like it was driven through a barbed wire fence.

Can anyone tell I did only the cab?

Your 68 looks awesome how it is. Here’s my 67 I put the hubcaps back on today. On mine it seems everything I have to fix stands out so I try to leave it alone
Posted via Mobile Device

**nlped** · 03-13-2019, 09:54 PM

Quote:

Originally Posted by Thrill4130

Your 68 looks awesome how it is. Here’s my 67 I put the hubcaps back on today. On mine it seems everything I have to fix stands out so I try to leave it alone
Posted via Mobile Device

They both look killer!!! I’ve got one too, but mine won’t be so original underneath.

**davischevy** · 03-13-2019, 10:05 PM

Quote:

Originally Posted by 89AKurt

Not sure if it's worth the trouble, cleaned up the aluminum trim with steel wool. It's all trashed, front fender arch looks like it was driven through a barbed wire fence.

Can anyone tell I did only the cab?

My dad bought the twin to that truck brand new in the fall of 67.

toolboxchev · 03-14-2019, 01:29 PM

Quote:

Originally Posted by 89AKurt

Not sure if it's worth the trouble, cleaned up the aluminum trim with steel wool. It's all trashed, front fender arch looks like it was driven through a barbed wire fence.

Can anyone tell I did only the cab?

Hey I think its awesome that you are keeping it original for now. Time capsule from the past, brought back to life.

Dig IT!

machas74 · 03-14-2019, 02:08 PM

I added 383 emblem on hood.

Toms67 · 03-14-2019, 06:58 PM

Quote:

Originally Posted by SlowGreen71

Shortened her up a little and changed over to 73-87 style engine mounts. Still need to finish welding the inner sleeve and smoothing the cuts for the motor stands but it’s all in.

Nice job. Looks good.

**Speedracer39** · 03-14-2019, 08:08 PM

Finally finished assembly of new engine trying to get caught up with a few other repairs before install.

**Boog** · 03-14-2019, 09:34 PM

Turn.

Ben IV · 03-14-2019, 10:27 PM

Started on a carb rebuild. Never touched a quadrajet before.

**Steeveedee** · 03-14-2019, 11:42 PM

If you don't have one yet, get one of the books on rebuilding Q-Jets. The sheet that comes with the carb leaves a lot of necessary information uncovered.

66clow · 03-15-2019, 07:25 AM

Hammer dolly hammer dolly

89AKurt · 03-15-2019, 12:02 PM

Quote:

Originally Posted by JustToxic

Started putting new floor boards in the cab over the weekend. New kick panels, lower A-pillar, DS forward cab support, Inner and outer rockers, PS rear cab support and finally Cab corners.

That's something I *should do* in the future, there are pop-riveted aluminum pieces now, but still need to slow down when crossing a puddle. LOL

Appreciate everyone responding to my cheapskate task!

67/70C10SHORTY · 03-15-2019, 03:10 PM

I almost got motivated to work on my truck today

03-11-2019, 12:53 PM	#352
89AKurt Registered User Join Date: Dec 2015 Location: Prescott Arizona Posts: 621	Re: What did you do to your truck today.The 3rd chapter Not sure if it's worth the trouble, cleaned up the aluminum trim with steel wool. It's all trashed, front fender arch looks like it was driven through a barbed wire fence. Can anyone tell I did only the cab? __________________ 1968 Long Bed 2016 Honda Civic Coupe EX-T ticket magnet

03-11-2019, 01:07 PM	#353
weq92f Registered User Join Date: Oct 2016 Location: Dallas Texas Posts: 3,217	Re: What did you do to your truck today.The 3rd chapter . Can't tell with that image, no. Too poor quality and the angle is wrong for comparison. But... it does look good to me! -klb __________________ 67 C10 fleet fuel injected '70 402, 700r4, 3.73 posi 07 335 sport turbo 6sp 94 Trans Am GT LT1 6sp posi -- sold after 22yrs 99 540 sport V8 6sp -- sold 73 240z L24 4sp -- given to friend 68 C10 step 350/350 3.73 open -- sold

03-11-2019, 06:41 PM	#356
Barnfind46 Registered User Join Date: Aug 2014 Location: Mena,Arkansas Posts: 485	Re: What did you do to your truck today.The 3rd chapter Every little bit helps. The little things are what make a well kept daily driver stand out. I repainted the tailgate letters on my faded tailgate with a spray can and some tape. Made the truck look much better! __________________ 68' with no bells or whistles unless I add'em.

03-11-2019, 10:13 PM	#357
66clow Registered User Join Date: Jun 2012 Location: Clearwater Beach Florida Posts: 872	Re: What did you do to your truck today.The 3rd chapter Recived my bolt on firewall panels from Atomic Armadillo Metal Fab. Excellent fit. Attached Images

03-11-2019, 11:28 PM	#359
SoCoC10 Senior Member Join Date: Nov 2014 Location: Colorado Posts: 3,334	Re: What did you do to your truck today.The 3rd chapter Installed new trim on the K10 Cheyenne. Final door and fender fitment is next. Attached Images __________________ 07' Extcab Silverado Z71 Silver Birch, 5.3L HO 71' Cheyenne C10 Hugger Orange on Saddle SWB Besides these two, too Many to count

03-12-2019, 09:21 AM	#361
Andy4639 Old member Join Date: Jan 2002 Location: Liberty, & Garden City S.C. , U.S. Posts: 19,945	Re: What did you do to your truck today.The 3rd chapter I loaded the ramp truck yesterday for the 5hr trip to the beach for the big one in SC. First show of the season for me. Attached Images __________________ 1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs.

03-12-2019, 10:04 AM	#362
JustToxic Registered User Join Date: Jul 2016 Location: Elkhart, Indiana Posts: 292	Re: What did you do to your truck today.The 3rd chapter Started putting new floor boards in the cab over the weekend. New kick panels, lower A-pillar, DS forward cab support, Inner and outer rockers, PS rear cab support and finally Cab corners. Attached Images __________________ 1967 Chevy C20 to K20 Conversion "Simply Toxic" http://67-72chevytrucks.com/vboard/s...d.php?t=749409 1971 Chevy C20 Custom Camper LS Swap http://67-72chevytrucks.com/vboard/s...d.php?t=763775

03-14-2019, 02:08 PM	#367
machas74 Registered User Join Date: Feb 2019 Location: CA Posts: 9	Re: What did you do to your truck today.The 3rd chapter I added 383 emblem on hood. Attached Images

03-14-2019, 08:08 PM	#369
Speedracer39 Senior Member Join Date: Sep 2016 Location: Omaha Nebraska Posts: 596	Re: What did you do to your truck today.The 3rd chapter Finally finished assembly of new engine trying to get caught up with a few other repairs before install. Attached Images

03-14-2019, 09:34 PM	#370
Boog laying low Join Date: Mar 2001 Location: Searcy, Ark. USA Posts: 13,513	Re: What did you do to your truck today.The 3rd chapter Turn. Attached Images __________________ Boog 69 Chevy stepside, 358/T350, 4.11 posi, 4.5/4 drop, rallys, poboy driver primer is finer 91 Chevy sportside, Tahoe, Yukon & GMC Crewcab All GM..'nuff said. I stand for the flag and kneel at the cross

03-14-2019, 10:27 PM	#371
Ben IV Registered User Join Date: Dec 2006 Location: Glenpool OK Posts: 255	Re: What did you do to your truck today.The 3rd chapter Started on a carb rebuild. Never touched a quadrajet before. Attached Images __________________ 70 GMC custom short bed conversion 69 GMC panel truck

03-14-2019, 11:42 PM	#372
Steeveedee Who Changed This? Join Date: Jan 2013 Location: Simi Valley, CA Posts: 10,673	Re: What did you do to your truck today.The 3rd chapter If you don't have one yet, get one of the books on rebuilding Q-Jets. The sheet that comes with the carb leaves a lot of necessary information uncovered. __________________ ~Steven '70 Chevy 3/4T Longhorn CST 402/400/3.56 Custom Camper Simi Valley, CA

03-15-2019, 07:25 AM	#373
66clow Registered User Join Date: Jun 2012 Location: Clearwater Beach Florida Posts: 872	Re: What did you do to your truck today.The 3rd chapter Hammer dolly hammer dolly Attached Images

03-15-2019, 03:10 PM	#375
67/70C10SHORTY Registered User Join Date: Dec 2016 Location: Tucson, AZ Posts: 2	Re: What did you do to your truck today.The 3rd chapter I almost got motivated to work on my truck today Attached Images



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.