What did you do with your truck today, Part 3 - Page 156 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

evilokc · 10-11-2019, 10:10 PM

today was our first cold day in Oklahoma. the wind chill was like 26 and the wind was blowing pretty hard. ive been daily driving my truck all week and its been great fun. today i went out in the freezing 6am weather and of course the death rattle fired perfectly but when I started driving my hands were cold and I was thinking I should have brought gloves. it was right about then that I looked down and realized I just installed HEAT! i hadn't even tried the heater yet. no clue if it worked. turned my vintage heat/air/defrost to heat and cranked it up. sucker gets hot and blows hard. it was awesome! grinned all the way.

**oldman3** · 10-11-2019, 11:17 PM

Quote:

Originally Posted by evilokc

today was our first cold day in Oklahoma. the wind chill was like 26 and the wind was blowing pretty hard. ive been daily driving my truck all week and its been great fun. today i went out in the freezing 6am weather and of course the death rattle fired perfectly but when I started driving my hands were cold and I was thinking I should have brought gloves. it was right about then that I looked down and realized I just installed HEAT! i hadn't even tried the heater yet. no clue if it worked. turned my vintage heat/air/defrost to heat and cranked it up. sucker gets hot and blows hard. it was awesome! grinned all the way.

Super...Jim

evilokc · 10-12-2019, 12:03 AM

this isn't the place for this but ive never been a "rules: guy. I posted a thread looking for a bracket. haven't found it yet. if you guys can help I appreciate it.

Black_Sheep · 10-12-2019, 06:53 PM

I got the new calipers, front brake hoses and rear wheel cylinders changed out today. I still have to replace the hose from the frame to the diff, then the system will be ready for bleeding. As long as it's off the ground I'm going to clean up the wheel wells and grease the front end before buttoning it all back up.

I'm anxious to see how much difference there is between the 8" dual diaphragm booster, and the 7" single diaphragm booster it replaced.

evilokc · 10-12-2019, 09:51 PM

moved the power steering belt to the correct groove in the pulley so it would track straight. leaned it out by an 1/8 of a turn. i think its about right mixture wise. no more heavy exhaust smell on a cold start and no fumes when sitting at a light. its carbureted so it will never be fume free but its good now. drove many miles this week.

nvrdone · 10-13-2019, 02:34 PM

hey black sheep: how about some details on your disc brake change--- what parts did you use for the disc setup, master cylinder & booster? thanks

MiraclePieCo · 10-13-2019, 05:55 PM

Screwed down my shifter boot, then punched holes in my floor mat to secure it on those weird little holding nails on the floor of ADs. Then installed a one-piece carpet floor mat that's removable for cleaning.

DransportGarage · 10-13-2019, 07:30 PM

Washed my seat bases, then painted them with a poof can down in the wood shop. Wired everything on the engine. Did some plumbing on the heater and A/C lines that required removing the compressor and drilling the intake. I pick up my seats and visors tomorrow!

evilokc · 10-13-2019, 09:37 PM

adjusted all the belts and changed the bolts on the a/c compressor. I also tightened a couple of bolts that were allowing some rattling in the cab. drove about 30 miles today just running errands and taking the wife out for lunch.

MiraclePieCo · 10-13-2019, 09:38 PM

Quote:

Originally Posted by DransportGarage

Washed my seat bases, then painted them with a poof can down in the wood shop. Wired everything on the engine. Did some plumbing on the heater and A/C lines that required removing the compressor and drilling the intake. I pick up my seats and visors tomorrow!

So close - I'll bet you're counting the hours now!

69CST4x4SWB · 10-14-2019, 12:22 AM

Quote:

Originally Posted by MiraclePieCo

Eat tacos while you watch them, that will straighten them right out.

That would work too since I LOVE TACOS!!!

69CST4x4SWB · 10-14-2019, 12:24 AM

Quote:

Originally Posted by MiraclePieCo

Screwed down my shifter boot, then punched holes in my floor mat to secure it on those weird little holding nails on the floor of ADs. Then installed a one-piece carpet floor mat that's removable for cleaning.

Looks great Mark!

69CST4x4SWB · 10-14-2019, 12:28 AM

Quote:

Originally Posted by lgoodso1

Another picture finally figured out how to rotate the pics so they upload correctly.Attachment 1947951

Thank you, that's much better. Now I can see just how kick ass your truck is!

69CST4x4SWB · 10-14-2019, 12:52 AM

Polished on my grille some. Any suggestions on how to speedup the process on a 69-70 Chevy?

DransportGarage · 10-14-2019, 07:52 AM

Quote:

Originally Posted by MiraclePieCo

So close - I'll bet you're counting the hours now!

Looks like a couple hundred hours yet, but I've been counting them for some time. I need to re-position the seats, design and build door panels, do a final build on the console, install the windshield (which doesn't fit well), front end, bed, gas tank, steering column/shaft, sound system, finish the wiring and install the carpets. As we all know, there are a hundred other things I'm forgetting. Spring will be here soon!

evilokc · 10-15-2019, 07:54 PM

drove all over town. went to advanced auto to buy a new coolant temp pigtail. they had the one I was looking for but it was $7 on line and $20 in the store. I understand overhead and I want the local shops to stay in business but I cant pay that much of a mark up. ordered it. probably 40 miles today. running great

**idbeast** · 10-15-2019, 10:15 PM

Quote:

Originally Posted by evilokc

drove all over town. went to advanced auto to buy a new coolant temp pigtail. they had the one I was looking for but it was $7 on line and $20 in the store. I understand overhead and I want the local shops to stay in business but I cant pay that much of a mark up. ordered it. probably 40 miles today. running great

I ran all over town doing errands, stopped by a good friends sons auto tint place to see if he could do a clear bra on the Beast and the cost. As I was getting ready to leave he commented about how she must be insane when I get on it... so of course I opened the exhaust cutouts got a roiling start and floored it. Damn throttle stuck wide open, brakes didn't help much with the 499 ft. lbs. of torque, so I shut off the key and stood on the brakes... Nice to know I have the 4 wheel disk set up right, stopped straight and short...

Truck is parked until I figure out why the throttle linkage is heavily binding up, must likely a broken motor mount....

Jim W

Black_Sheep · 10-15-2019, 11:09 PM

Quote:

Originally Posted by nvrdone

hey black sheep: how about some details on your disc brake change--- what parts did you use for the disc setup, master cylinder & booster? thanks

It's a '75 Nova front sub, the most exotic parts are the Centric drilled and slotted rotors and Baer "Sport" pads. The hydraulic components are just premium quality OEM replacement parts. Calipers are Raybestos remans and the rear wheel cylinders are new Raybestos. My rear is a Mopar 8.75" with 10" x 2.5" drums so I chose the closest size wheel cylinder to what the Nova would have, but they are .010" larger diameter. The new master cylinder and flex hoses are all NAPA brand. Rounding out the system is a Tuff Stuff Performance dual diaphragm 8" booster, residual pressure valves and a Wilwood adjustable proportioning valve. For a weekend cruiser it's a super simple disc/drum setup which was fairly economical, even with "premium" parts. We got them bled this evening and it has a good pedal. I want to replace the shocks before the tires go back on, hopefully I'll be able to test drive it Saturday...

Black_Sheep · 10-15-2019, 11:21 PM

I failed to mention the dual 8" booster replace a single 7" booster. It went from 38.5 square inches to 100.5 square inches of area by swapping boosters. It should provide noticeably more power assist

MARTINSR · 10-15-2019, 11:26 PM

Quote:

Originally Posted by DransportGarage

Washed my seat bases, then painted them with a poof can down in the wood shop. Wired everything on the engine. Did some plumbing on the heater and A/C lines that required removing the compressor and drilling the intake. I pick up my seats and visors tomorrow!

Man, your garage is awesome!

Got out in the garage and worked some on my selves, that was it, but getting closer!

Brian

DransportGarage · 10-16-2019, 12:17 AM

Quote:

Originally Posted by MARTINSR

Man, your garage is awesome!

Got out in the garage and worked some on my selves, that was it, but getting closer!

Brian

Thanks, Brian! That's the workshop in the basement. Me and the wife built our own house, and I convinced her I had to have that to do the hardwood floors and interior carpentry. Hee! Hee! The wall cabinet on the back wall is a modified Norm Abrams plan.

evilokc · 10-16-2019, 08:40 PM

aired up the tires and checked the brass on the radiator to see if it would polish. I think its going to shine up really nice. drove about 60 miles today

Johns327 · 10-16-2019, 11:33 PM

Spent the day hooking up the A/C lines. Yes, I know “winter is coming”, but it was a job I have been putting off due to the crummy access to the Freon lines in the cab. Now I need to get a vacuum pump and spend a day chasing leaks.

DransportGarage · 10-17-2019, 12:42 PM

Fitting the seats and console today, which lead to cutting the carpet so it can be sent out for binding. It's a little early for the carpet, but I wanted to be sure I had enough material. I'll end up with less than a square foot of scrap.

SPECIAL THANKS TO MIRACLE PIE CO for reminding me to use butcher/rosin paper as a template (Post #3813). I came close to scrapping my GTO carpet because I cut it in place.

lgoodso1 · 10-17-2019, 10:03 PM

Quote:

Originally Posted by 69CST4x4SWB

Thank you, that's much better. Now I can see just how kick ass your truck is!

Your welcome, and thank you

10-11-2019, 10:10 PM	#3876
evilokc Registered User Join Date: Mar 2013 Location: albuquerque New Mexico Posts: 522	Re: What did you do with your truck today, Part 3 today was our first cold day in Oklahoma. the wind chill was like 26 and the wind was blowing pretty hard. ive been daily driving my truck all week and its been great fun. today i went out in the freezing 6am weather and of course the death rattle fired perfectly but when I started driving my hands were cold and I was thinking I should have brought gloves. it was right about then that I looked down and realized I just installed HEAT! i hadn't even tried the heater yet. no clue if it worked. turned my vintage heat/air/defrost to heat and cranked it up. sucker gets hot and blows hard. it was awesome! grinned all the way.

10-12-2019, 12:03 AM	#3878
evilokc Registered User Join Date: Mar 2013 Location: albuquerque New Mexico Posts: 522	Re: What did you do with your truck today, Part 3 this isn't the place for this but ive never been a "rules: guy. I posted a thread looking for a bracket. haven't found it yet. if you guys can help I appreciate it.

10-12-2019, 06:53 PM	#3879
Black_Sheep Registered User Join Date: Jun 2017 Location: upper midwest Posts: 1,129	Re: What did you do with your truck today, Part 3 I got the new calipers, front brake hoses and rear wheel cylinders changed out today. I still have to replace the hose from the frame to the diff, then the system will be ready for bleeding. As long as it's off the ground I'm going to clean up the wheel wells and grease the front end before buttoning it all back up. I'm anxious to see how much difference there is between the 8" dual diaphragm booster, and the 7" single diaphragm booster it replaced. Attached Images __________________ Mark Brother's keeper - '58 Stepside build

10-12-2019, 09:51 PM	#3880
evilokc Registered User Join Date: Mar 2013 Location: albuquerque New Mexico Posts: 522	Re: What did you do with your truck today, Part 3 moved the power steering belt to the correct groove in the pulley so it would track straight. leaned it out by an 1/8 of a turn. i think its about right mixture wise. no more heavy exhaust smell on a cold start and no fumes when sitting at a light. its carbureted so it will never be fume free but its good now. drove many miles this week. Last edited by evilokc; 10-12-2019 at 10:00 PM.

10-13-2019, 02:34 PM	#3881
nvrdone Registered User Join Date: Dec 2011 Location: Moxee WA Posts: 1,479	Re: What did you do with your truck today, Part 3 hey black sheep: how about some details on your disc brake change--- what parts did you use for the disc setup, master cylinder & booster? thanks

10-13-2019, 05:55 PM	#3882
MiraclePieCo Registered User Join Date: Sep 2014 Location: USA Posts: 2,249	Re: What did you do with your truck today, Part 3 Screwed down my shifter boot, then punched holes in my floor mat to secure it on those weird little holding nails on the floor of ADs. Then installed a one-piece carpet floor mat that's removable for cleaning. Attached Images __________________ 1951 Chevy Panel Truck

10-13-2019, 07:30 PM	#3883
DransportGarage Registered User Join Date: Feb 2010 Location: Lebanon, Ohio Posts: 1,359	Re: What did you do with your truck today, Part 3 Washed my seat bases, then painted them with a poof can down in the wood shop. Wired everything on the engine. Did some plumbing on the heater and A/C lines that required removing the compressor and drilling the intake. I pick up my seats and visors tomorrow! Attached Images __________________ Bob "It won't take long and it won't cost much." '55 3100 (383/700R4)--'55 Belair Sedan (350/4-speed)--'64 'Vette Conv. (327/4-speed)--'68 GTO Conv. (462/4-speed)--'69 Cutlass Conv. (350/TH350)--'06 'Vette Conv. (LS2/6-speed) Bob's Retirement Build - My 55 TF Bob's 700R4 Build (how-to)

10-13-2019, 09:37 PM	#3884
evilokc Registered User Join Date: Mar 2013 Location: albuquerque New Mexico Posts: 522	Re: What did you do with your truck today, Part 3 adjusted all the belts and changed the bolts on the a/c compressor. I also tightened a couple of bolts that were allowing some rattling in the cab. drove about 30 miles today just running errands and taking the wife out for lunch.

10-14-2019, 12:52 AM	#3889
69CST4x4SWB Registered User Join Date: Sep 2010 Location: Oregon, The Beautiful Pacific Northwest (GOD'S country) Posts: 151	Re: What did you do with your truck today, Part 3 Polished on my grille some. Any suggestions on how to speedup the process on a 69-70 Chevy? __________________ In GOD I Trust All Others I Question!!! 1969 Chevy CST K/10 SWB (Legs) 1969 Chevy C/20 LWB (Old Gray Mare) Donor 1972 GMC 1500 Sierra Grande (Orange Creamsicle) Sold 1979 Chevy C/30 Cheyenne Flatbed Dually (FatBoy) Sold 1991 Chevy Silverado Ext Cab (LowBoy) Sold 2008 Harley Davidson Electra Glide (Black Betty) Mark ~ US ARMY VETERAN 2nd ARMORED DIVISION 67th ARMOR

10-15-2019, 07:54 PM	#3891
evilokc Registered User Join Date: Mar 2013 Location: albuquerque New Mexico Posts: 522	Re: What did you do with your truck today, Part 3 drove all over town. went to advanced auto to buy a new coolant temp pigtail. they had the one I was looking for but it was $7 on line and $20 in the store. I understand overhead and I want the local shops to stay in business but I cant pay that much of a mark up. ordered it. probably 40 miles today. running great

10-15-2019, 11:21 PM	#3894
Black_Sheep Registered User Join Date: Jun 2017 Location: upper midwest Posts: 1,129	Re: What did you do with your truck today, Part 3 I failed to mention the dual 8" booster replace a single 7" booster. It went from 38.5 square inches to 100.5 square inches of area by swapping boosters. It should provide noticeably more power assist __________________ Mark Brother's keeper - '58 Stepside build

10-16-2019, 08:40 PM	#3897
evilokc Registered User Join Date: Mar 2013 Location: albuquerque New Mexico Posts: 522	Re: What did you do with your truck today, Part 3 aired up the tires and checked the brass on the radiator to see if it would polish. I think its going to shine up really nice. drove about 60 miles today

10-16-2019, 11:33 PM	#3898
Johns327 Registered User Join Date: Jun 2017 Location: Bonsall, CA Posts: 104	Re: What did you do with your truck today, Part 3 Spent the day hooking up the A/C lines. Yes, I know “winter is coming”, but it was a job I have been putting off due to the crummy access to the Freon lines in the cab. Now I need to get a vacuum pump and spend a day chasing leaks. Attached Images __________________ 1955 second series, 3200 standard bed, big window. Owned since 1975, decided it was time to do a frame off. 327, 4L80e, Ford 9 inch.

10-17-2019, 12:42 PM	#3899
DransportGarage Registered User Join Date: Feb 2010 Location: Lebanon, Ohio Posts: 1,359	Re: What did you do with your truck today, Part 3 Fitting the seats and console today, which lead to cutting the carpet so it can be sent out for binding. It's a little early for the carpet, but I wanted to be sure I had enough material. I'll end up with less than a square foot of scrap. SPECIAL THANKS TO MIRACLE PIE CO for reminding me to use butcher/rosin paper as a template (Post #3813). I came close to scrapping my GTO carpet because I cut it in place. Attached Images __________________ Bob "It won't take long and it won't cost much." '55 3100 (383/700R4)--'55 Belair Sedan (350/4-speed)--'64 'Vette Conv. (327/4-speed)--'68 GTO Conv. (462/4-speed)--'69 Cutlass Conv. (350/TH350)--'06 'Vette Conv. (LS2/6-speed) Bob's Retirement Build - My 55 TF Bob's 700R4 Build (how-to)



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.