![]() |
|
![]() |
#1 |
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,982
|
Re: Project: Recycle
I did notice one thing I'm not happy about & will consider it a 'lesson learned'.
I cleaned a bunch of areas on the frame w/a cut-off wheel on the angle grinder. The 60-grit sanding discs would 'load-up' w/the OE coating on the frame or from the coating on the new steel. The edge of the cut-off wheel sanded through it w/o issue so I used it for stripping the old stuff off. As mentioned in an earlier post, just before taking everything to the coaters, I went over everything again w/some 60-grit discs. The frame appeared very uniform. I can clearly see where the cut-off disc (used @ an angle) gouged the steel during the stripping process. It's not the end of the world but I don't like that it's there. I'd hope to get a few pics today but the painting process is deciding otherwise. I still had some misc brackets that needed attention & started working on them yesterday along w/the a-arms. I decided to use Rustoleum brand paints after seeing a couple of members use them. I got the 'professional' series that indicates "quick drying" times but I'm not seeing it (can indicates 15-20mins between coats/dry to touch). Because of the recent weather, I'm painting in a boiler room @ work for consistency. The room temp varies between 90-100°F & it's dry..... Paint drying times for me?? 30-40 mins & the stuff is still tacky (I'm not putting down wet coats either). Back to VHT for me.....
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. Last edited by SCOTI; 11-13-2010 at 08:55 PM. |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Jul 2006
Location: the netherlands europe
Posts: 4,335
|
Re: Project: Recycle
hmmm the long drying times might be because the paint is too thick or aplied too thick , it could allso be that the paint is reacting to the new powdercoat , talk to the powdercoat man about that one maibe he knows
personally i would keep using the rustoleum
__________________
i got a job again and having fun at it too idea's for the trucks and the order of things to do are taking shape and get closer to being realized , a few more months and i be able to start building for real i complete 2 of the trucks intoo running fashion one custom and one basicly stock the thirth will be sacrificed for parts |
![]() |
![]() |
![]() |
#3 | |
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,982
|
Re: Project: Recycle
Quote:
I've shot enough paint from a rattle can to know a dry coat to a medium or wet. I shot the parts dry to medium. There's enough orange peel to suggest I'm not laying it on wet enough but I can't imagine how long that would take to set up. I shot one part Thursday night (a small spacer). It sat for approx 1-1.5hrs before I cleaned up for the night. It was dry to the touch so I moved it to another spot for overnight storage. When I went to install it Friday afternoon, it was stuck to the surface I placed it on (remember, it was dry to the touch). I've used Rustoleum brand paint before & did not like the long drying times (I don't see how you can get good results shooting a part in your driveway or garage where conditions are never optimum w/such a long 'dry time'). This is why I tried this 'professional' series because it's supposed to dry much faster.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. Last edited by SCOTI; 11-14-2010 at 03:09 AM. |
|
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Jun 2007
Location: DFW (Forney)
Posts: 1,529
|
Re: Project: Recycle
Yeah, Rustoleum exaggerates their dry times quite a bit.
__________________
'58 SWB Fleetside...Front & Rear Porterbuilt Dropmember, 6.0 LS /4L60E. Accuair E-level, 20 Billet Specialties (Vintecs) '63 Buick Riviera ... AccuAir E-level, 20" Billet Specialties (Vintecs) http://67-72chevytrucks.com/vboard/s...=528853&page=5 |
![]() |
![]() |
![]() |
#5 |
Registered User
![]() Join Date: Jul 2006
Location: Ozark, MO
Posts: 4,887
|
Re: Project: Recycle
Hmmm, I just picked up a rattle can of the rustoleum pro today for the same use, a few spots on the frame that don't justify mixing and shooting a pot of epoxy. I'll let you know what my dry times are, it's about 60 degrees here too so that will be a test.
I like the rustoleum etch primer in a can for small parts, it sticks like real etch and i just topcoat it with whatever black I have laying around.
__________________
'20 Silverado Trail Boss ~ '17 Tahoe ~ '79 K15 Sierra Grande ~ '76 Blazer 2wd ~ '71 Cheyenne swb ~ '55 Pontiac Safari ~'50 3100 bagged ~ '80 Wife ~ Late model kids
Last edited by LEEVON; 11-14-2010 at 04:28 PM. |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,982
|
Re: Project: Recycle
Well, not much of an update but my buddy Matt that was w/me to pick-up the parts & get the main x-members connected last Thursday sent me some pics he took that day.
I got the BJ's pressed out of the lower a-arms, got them taped off, degreased, & in some Rustoleum primer. The uppers got the bushings taped off & then degreased before I ran out of time on Sat night. I wanted to get the uppers in primer but there wasn't enough in the can to get even one partially done & a trip to the local hardware joint would have added @ least another 40mins to the drill so I held off. I was sick Mon + Tues & spent today trying to get back up to speed. Maybe tomorrow I'll get the uppers primed & then some....
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. Last edited by SCOTI; 11-17-2010 at 11:48 PM. |
![]() |
![]() |
![]() |
#7 |
Happy to be here
![]() Join Date: Mar 2000
Location: Cypress, TX
Posts: 39,023
|
Re: Project: Recycle
There is a formula to correct the Rustoleum "advertised" dry time. I believe you multiply the hours suggested x days and it comes out about right. 3-4 hours dry time equates to 3-4 days if I'm not mistaken...
![]()
__________________
Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra" |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Jun 2007
Location: DFW (Forney)
Posts: 1,529
|
Re: Project: Recycle
Sounds about right
__________________
'58 SWB Fleetside...Front & Rear Porterbuilt Dropmember, 6.0 LS /4L60E. Accuair E-level, 20 Billet Specialties (Vintecs) '63 Buick Riviera ... AccuAir E-level, 20" Billet Specialties (Vintecs) http://67-72chevytrucks.com/vboard/s...=528853&page=5 |
![]() |
![]() |
![]() |
#9 |
Tot Roddin'
Join Date: Apr 2005
Location: Mid-MO
Posts: 24,461
|
Re: Project: Recycle
Those rails look good SCOTI!
__________________
-Nate ![]() 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package) |
![]() |
![]() |
![]() |
#10 |
67cheby
![]() Join Date: Sep 2008
Location: siloam springs ar 72761
Posts: 17,890
|
Re: Project: Recycle
looks Slick
|
![]() |
![]() |
![]() |
#11 |
PROJECT 7DEUCE
![]() Join Date: Dec 2002
Location: GRANTS PASS OR
Posts: 21,608
|
Re: Project: Recycle
Looks great scoti I was debating on doing this to mine and it looks like you got me talked into it.
__________________
GO BIG GREEN ![]() MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P.. Last edited by FRENCHBLUE72; 11-21-2010 at 09:46 AM. |
![]() |
![]() |
![]() |
#12 |
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,982
|
Re: Project: Recycle
Yes. Everything re-fastened w/bright yellow zinc plated GRADE-8 hardware w/lock washers (both sides) & nyloc nuts. The truck arm front mounts are actually GRADE-9 fasteners (fine thread, w/dual lock washers & nyloc nuts) sice they're spaced away from the x-member vs. being bolted directly against the x-member.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. Last edited by SCOTI; 11-21-2010 at 11:40 AM. |
![]() |
![]() |
![]() |
#13 |
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,982
|
Re: Project: Recycle
My buddy Matt showed up tonight so we were able to measure the frame for square. We measured from a small notch in each rail (located near the front x-member bolt) back to the last 2 OE punched holes on the top of the rails. Over a span of 13', we were .125 off.
So the front x-member & associated parts are officially tightend down. I was hoping to hang the a-arms & spindles but the backing plate bolt holes need to be tapped on the spindles & the upper a-arm BJ bolts were too long (couldn't get the exact size I wanted today). I'll correct those issues tomorrow. Matt took the HD drums w/him & will get them turned for me @ his work. I still need to do more cleaning on the rear housing before parts can be attached or color can be applied. Gettin' closer . . .....
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. Last edited by SCOTI; 11-24-2010 at 12:38 AM. |
![]() |
![]() |
![]() |
#14 |
67cheby
![]() Join Date: Sep 2008
Location: siloam springs ar 72761
Posts: 17,890
|
Re: Project: Recycle
worthless without pics
|
![]() |
![]() |
![]() |
#15 |
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,982
|
Re: Project: Recycle
It would just be the same ol stuff
![]() Today I worked on tightening more of the various x-members (front splash pan, rear shock x-member, Panhard bar x-member), & I bolted up the front-bumper frame brackets. I figured I'm @ the point of installing the front a-arms, spindles, brakes, & rear suspension, so off the frame 'jig' it came. It's officially on jackstands. ![]()
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
![]() |
![]() |
![]() |
#16 |
Slots go on anything!
Join Date: May 2003
Location: Richardson, TX
Posts: 5,957
|
Re: Project: Recycle
Right on!
__________________
1974 Jimmy- 5.3/4L80e/NP241 |
![]() |
![]() |
![]() |
#17 |
67cheby
![]() Join Date: Sep 2008
Location: siloam springs ar 72761
Posts: 17,890
|
Re: Project: Recycle
great progress
|
![]() |
![]() |
![]() |
#18 |
Village Idiot....
Join Date: Jul 2003
Location: Rowlett, Texas
Posts: 1,833
|
Re: Project: Recycle
All this and still no pictures.....................
![]()
__________________
http://www.hubgarage.com/mygarage/n2billet -67 SWB Custom Porterbuilt Front and rear 20/22's Hazel Sold -71 StepSide Porterbuilt Stage 2 with 20/22's Stella Mae Sold |
![]() |
![]() |
![]() |
#19 | |
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,982
|
Re: Project: Recycle
Quote:
Edit: I added these cell pics I took mid day to send to Matt. He also took a couple of pics from his phone which are typically very decent. I'm waiting for them to upload to my e-mail & I'll post them up once they do....
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. Last edited by SCOTI; 11-29-2010 at 01:05 PM. |
|
![]() |
![]() |
![]() |
#20 |
low n' slo
![]() Join Date: Mar 2009
Location: rosenberg, texas
Posts: 5,167
|
Re: Project: Recycle
^^^ lol
progress is progress man, your doin some nice detailed work! ......now post some pics ![]()
__________________
67 1/2 ton Suburban - Project DRGNWGN. Build thread ![]() -_--_--_ _________ _--_-_ -/____|__|__\__ ,.,,,.,.,,.,|_O _______ O_] |
![]() |
![]() |
![]() |
#21 |
Happy to be here
![]() Join Date: Mar 2000
Location: Cypress, TX
Posts: 39,023
|
Re: Project: Recycle
Progress looks good Scot. Crappy pics, set backs, and all aside it still looks much better than a bare frame.
__________________
Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra" |
![]() |
![]() |
![]() |
#22 |
67cheby
![]() Join Date: Sep 2008
Location: siloam springs ar 72761
Posts: 17,890
|
Re: Project: Recycle
looks sweet did you have the billet brake line clamps made or is it something you can buy, they look great !!
|
![]() |
![]() |
![]() |
#23 |
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,982
|
Re: Project: Recycle
Had some made after ordering in something similar (but different size). **Edited w/the pics Matt took.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. Last edited by SCOTI; 11-29-2010 at 01:06 PM. |
![]() |
![]() |
![]() |
#24 |
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,982
|
Re: Project: Recycle
Truck arms tight w/pinion shims installed. Prob will swap the 3° shims for the 2.5° set.
Got the correct 'front' truck arm bolts & nylock nuts. The one's previously installed were coarse thread & barely long enough. I swapped them for some longer, fine thread bolts (I used fine thread on the TA mounts too). I got new upper a-arm nuts & got them installed. I decided to just clean & paint the existing OE washers & run them. It's not 100% tight but snugged down (waiting to set it on the ground under weight before final tightening). I then went to snug up the lower a-arm hardware & realized the bushing 'sleeves' were too long. A quick text to Mr. Porter confirmed they're trim to fit so I took care of that. I didn't have the correct upper shock bolts (too short) so I got longer ones & swapped them in place. Other than that, trips to Fastenall & Lowes to swap some 'un-used' hardware for different stuff I will use. I've been moving the rear HD drum set-up in & out of the truck hoping to have enough time to get them in color & swapped into place but haven't had enough time yet. Need to get the front rotors in color as well so they can be installed . ....
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. Last edited by SCOTI; 12-02-2010 at 12:28 AM. |
![]() |
![]() |
![]() |
#25 |
67cheby
![]() Join Date: Sep 2008
Location: siloam springs ar 72761
Posts: 17,890
|
Re: Project: Recycle
the new pics look super nice , very detailed nice work !!
|
![]() |
![]() |
![]() |
Bookmarks |
|
|