What Did You Do With Your Truck Today ? - Page 16 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

FFredo · 01-12-2012, 11:47 AM

Dan, I sure hopew so, I'd expect no less
Mark, the tape measure sleeps with the fishes

mknittle · 01-12-2012, 07:26 PM

Quote:

Originally Posted by FFredo

Dan, I sure hopew so, I'd expect no less
Mark, the tape measure sleeps with the fishes

And good riddance!

**Dan in Pasadena** · 01-13-2012, 01:46 AM

Quote:

Originally Posted by FFredo

...Mark, the tape measure sleeps with the fishes

Makes me laugh because I admit to getting PISSED at a tool in the past and ...uh...."expressing" my upset with a BFH!

tbrown5079 · 01-13-2012, 08:51 AM

Spent an hour at the hose shop getting power steering hoses made up. Pick them up today. Trimmed camaro radiator mounting tabs and started removing inside angles on the core support to give room to lower the radiator in. Someday...............

oldcouple · 01-15-2012, 11:21 PM

Quote:

Originally Posted by tbrown5079

Spent an hour at the hose shop getting power steering hoses made up. Pick them up today. Trimmed camaro radiator mounting tabs and started removing inside angles on the core support to give room to lower the radiator in. Someday...............

Had mine made by these guys..http://nevadahouseofhose.com/

catchy name and they used to have a great calendar.

meter swinger · 01-16-2012, 01:30 AM

Got it back from my buddy chris who re-wired it for me. I drove it up and down the street just so the neighbors would know its back.

got a lot of work ahead on this sucker. If i can get home in daylight ill get some new pics and get a build thread started.
Posted via Mobile Device

mknittle · 01-12-2012, 07:31 PM

I worked on my lower control arm hangers and made a template for the frame boxing plates.

meter swinger · 01-12-2012, 07:53 PM

Got a call from my buddy who is wiring my truck. Its done and i might pick it up this weekend.

then new motor/trans mounts, then the exhaust shop, then the gas tank, then the bed floor, then i'm broke again. Haha!
Posted via Mobile Device

ratrodmiller · 01-15-2012, 10:54 PM

I adjusted the pressure in my gm power steering pump today.Installed 3 shims and now the mustang power rack is alot happier with lowered pressure.

oldcouple · 01-18-2012, 09:13 PM

Tried to go outside, gave up, went back to bed, watching Barrett-Jackson now.

xpickup · 01-18-2012, 09:35 PM

Quote:

Originally Posted by oldcouple

Tried to go outside, gave up, went back to bed, watching Barrett-Jackson now.

oldcouple,Thank you. I did not know it was on. My wife will now be pissed that WE will watch it!

Shannon

meter swinger · 01-19-2012, 01:32 AM

Got the impala steering wheel on.
Now just waiting on parts.
Posted via Mobile Device

Tomb23 · 01-21-2012, 12:24 PM

Well tires and wheels finally under it!!

Hope I live long enough to DRIVE it someday?

lowdownstar · 01-21-2012, 12:52 PM

keep the faith man, the truck looks great with the new wheels! you'll be beating them up in no time

Ray

Daze57 · 01-21-2012, 01:38 PM

tomb23

you sound like me -livin long enough to drive it -mine has been down longer than i drove it -
your truck looks great good lookin motor - wheels - all around - good luck on finishing it - (that said in a good way)

Atommik · 01-21-2012, 11:00 PM

Finished the body work on the drivers door and epoxy primed it!!

lt155ruck · 01-22-2012, 02:29 AM

Put the cab on the frame today

mknittle · 01-22-2012, 12:33 PM

Quote:

Originally Posted by lt155ruck

Put the cab on the frame today

nice!

**Dan in Pasadena** · 01-24-2012, 07:47 PM

Quote:

Originally Posted by lt155ruck

Put the cab on the frame today

lt155truck, I see you put what I THINK is bedliner(?) in your footwell areas and under the front fenders. Do you plan to leave it as-is in the footwells or will it be covered with carpet, paint, etc?

Did you shoot it with a Shutz gun or roll it in there, or what? I looked for a thread on your truck but I didn't find one. If you DO have one, please provide a link.

lt155ruck · 01-24-2012, 11:49 PM

Quote:

Originally Posted by Dan in Pasadena

lt155truck, I see you put what I THINK is bedliner(?) in your footwell areas and under the front fenders. Do you plan to leave it as-is in the footwells or will it be covered with carpet, paint, etc?

Did you shoot it with a Shutz gun or roll it in there, or what? I looked for a thread on your truck but I didn't find one. If you DO have one, please provide a link.

Hi Dan, yes it is sprayed bedliner. The bottom of the cab is done as well for protection and sound deadening.The footwell area will be covered in bound carpet with a polished strip at the door edge. No build thread as of yet, but will probably get something going. Basically I have owned it for 17 years with most of that being in primer. I made the decision to finish it 4 years ago after being diagnosed with cancer at 38. All is good now but definately life altering. The truck has spend the last couple of years in bodyshop prison but was paroled recently. But was worth the wait. I hope to have it done this summer. Send me a PM if you have anymore questions.

mknittle · 01-22-2012, 07:09 PM

Quote:

Originally Posted by Daze57

tomb23

you sound like me -livin long enough to drive it -mine has been down longer than i drove it -
your truck looks great good lookin motor - wheels - all around - good luck on finishing it - (that said in a good way)

At least you got to drive yours! LOL

mknittle · 01-22-2012, 12:35 PM

Tuned up my sewing machine for some practice projects.

Rude Dude · 01-22-2012, 09:24 PM

Ran new fuel line front to rear, went out and bought an air angle drill made it so much easier, man I love air tools

*itstheshu* · 01-22-2012, 06:33 PM

started rewiring the dash

1959 Apache 3600 · 01-22-2012, 10:39 PM

Got everything organized and ready to rebuild the Quadrajet that goes on my big block.

01-12-2012, 11:47 AM	#1
FFredo Registered User Join Date: Apr 2011 Location: San Diego CA Posts: 241	Re: What Did You Do With Your Truck Today ? Dan, I sure hopew so, I'd expect no less Mark, the tape measure sleeps with the fishes

01-13-2012, 08:51 AM	#4
tbrown5079 Registered User Join Date: Feb 2007 Location: Blairsville, PA Posts: 301	Re: What Did You Do With Your Truck Today ? Spent an hour at the hose shop getting power steering hoses made up. Pick them up today. Trimmed camaro radiator mounting tabs and started removing inside angles on the core support to give room to lower the radiator in. Someday...............

01-16-2012, 01:30 AM	#6
meter swinger Registered User Join Date: Apr 2009 Location: Kennewick WA. Posts: 1,437	Re: What Did You Do With Your Truck Today ? Got it back from my buddy chris who re-wired it for me. I drove it up and down the street just so the neighbors would know its back. got a lot of work ahead on this sucker. If i can get home in daylight ill get some new pics and get a build thread started. Posted via Mobile Device Last edited by meter swinger; 01-16-2012 at 01:31 AM. Reason: +

01-12-2012, 07:31 PM	#7
mknittle Registered User Join Date: Jul 2011 Location: Auburn ca. Posts: 2,886	Re: What Did You Do With Your Truck Today ? I worked on my lower control arm hangers and made a template for the frame boxing plates. __________________ Mark My GMC build. http://67-72chevytrucks.com/vboard/s...d.php?t=536602

01-12-2012, 07:53 PM	#8
meter swinger Registered User Join Date: Apr 2009 Location: Kennewick WA. Posts: 1,437	Re: What Did You Do With Your Truck Today ? Got a call from my buddy who is wiring my truck. Its done and i might pick it up this weekend. then new motor/trans mounts, then the exhaust shop, then the gas tank, then the bed floor, then i'm broke again. Haha! Posted via Mobile Device

01-15-2012, 10:54 PM	#9
ratrodmiller Registered User Join Date: Feb 2009 Location: plain dealing,la Posts: 190	Re: What Did You Do With Your Truck Today ? I adjusted the pressure in my gm power steering pump today.Installed 3 shims and now the mustang power rack is alot happier with lowered pressure.

01-18-2012, 09:13 PM	#10
oldcouple Registered User Join Date: Nov 2011 Location: Winlock Wa Posts: 584	Re: What Did You Do With Your Truck Today ? Tried to go outside, gave up, went back to bed, watching Barrett-Jackson now. Attached Images __________________ Retired and too busy to work.

01-19-2012, 01:32 AM	#12
meter swinger Registered User Join Date: Apr 2009 Location: Kennewick WA. Posts: 1,437	Re: What Did You Do With Your Truck Today ? Got the impala steering wheel on. Now just waiting on parts. Posted via Mobile Device

01-21-2012, 12:24 PM	#13
Tomb23 Registered User Join Date: May 2004 Location: Eastern Oregon Posts: 201	Re: What Did You Do With Your Truck Today ? Well tires and wheels finally under it!! Hope I live long enough to DRIVE it someday? Attached Images

01-21-2012, 12:52 PM	#14
lowdownstar big guy Join Date: Jun 2008 Location: mass Posts: 820	Re: What Did You Do With Your Truck Today ? keep the faith man, the truck looks great with the new wheels! you'll be beating them up in no time Ray

01-21-2012, 01:38 PM	#15
Daze57 Registered User Join Date: Jul 2011 Location: Las Vegas - Nev. aka Sin City Posts: 1,835	Re: What Did You Do With Your Truck Today ? tomb23 you sound like me -livin long enough to drive it -mine has been down longer than i drove it - your truck looks great good lookin motor - wheels - all around - good luck on finishing it - (that said in a good way)

01-21-2012, 11:00 PM	#16
Atommik Registered User Join Date: Sep 2011 Location: Golden Valley,MN Posts: 639	Re: What Did You Do With Your Truck Today ? Finished the body work on the drivers door and epoxy primed it!! __________________ My build http://67-72chevytrucks.com/vboard/s...d.php?t=495795

01-22-2012, 02:29 AM	#17
lt155ruck Registered User Join Date: Jul 2010 Location: Victoria,B.C. Canada Posts: 175	Re: What Did You Do With Your Truck Today ? Put the cab on the frame today Attached Images

01-22-2012, 12:35 PM	#22
mknittle Registered User Join Date: Jul 2011 Location: Auburn ca. Posts: 2,886	Re: What Did You Do With Your Truck Today ? Tuned up my sewing machine for some practice projects. __________________ Mark My GMC build. http://67-72chevytrucks.com/vboard/s...d.php?t=536602

01-22-2012, 09:24 PM	#23
Rude Dude Registered User Join Date: Sep 2005 Location: Glendale Arizona Posts: 1,188	Re: What Did You Do With Your Truck Today ? Ran new fuel line front to rear, went out and bought an air angle drill made it so much easier, man I love air tools



Register or Log In To remove these advertisements.

01-22-2012, 06:33 PM	#24
itstheshu Account Suspended Join Date: May 2010 Location: san antonio texas Posts: 166	Re: What Did You Do With Your Truck Today ? started rewiring the dash

01-22-2012, 10:39 PM	#25
1959 Apache 3600 Registered User Join Date: Aug 2011 Location: Western Iowa Posts: 147	Re: What Did You Do With Your Truck Today ? Got everything organized and ready to rebuild the Quadrajet that goes on my big block.

Register or Log In To remove these advertisements.