What did you do to your truck today!

[ItsRandy]

Finished wiring my power windows (they even work), installed new headlight switch, got the new dome light working and installed a new Optima battery.

[hockeyjerk1]

Finished installing trim and modified my stake pockets into tie downs, but there only strong enough for tarps.

[67cheby]

set my new exhaust manifolds on my motor !

[ChrisWhewell]

I replaced the grade 5 bolt that was in the middle of the torsional damper with a $25 bolt from ARP.

[bollybib]

I gave it a good scrub for the Brothers Bash on Sunday.

[ItsRandy]

I installed new door latch plates and new door weather stripping.

[Tmwoodall]

Installed my Captinfab brackets and got the misc hydroboost parts all mounted up. All but the last line from the T on the low pressure are cut and installed. Made my own plunger end, and made my own (Pops did most of the work) output shaft with my "lathe" since my unit came without the output shaft. Ordering real clamps this week to replace the pegboard stand-ins.

Installed my rear Wilwood disc w/internal e-brake kit, along with new wheel bearings and seals.

Welded up the fresh air vents and got the interior firewall/floor kickboard epoxyed.

I love a good week off, even if I didn't spend as much time in the garage as I wanted.

[Tmwoodall]

Photo upload isn't being friendly today. Smaller set here.

[67cheby]

great progress !

[OJ1988]

Started my new engine for the first time today!

Got a squeling belt, not sure if it's actually the alt or the water pump. It's lined up real good, but squels real bad and alt pulley gets very hot!
Posted via Mobile Device

[oklalawnboy]

Originally Posted by OJ1988

Started my new engine for the first time today!

Got a squeling belt, not sure if it's actually the alt or the water pump. It's lined up real good, but squels real bad and alt pulley gets very hot!
Posted via Mobile Device

Belt could be a little loose but also the alt may be pulling real hard trying to charge the low battery. Tighten the belt a bit and charge the battery. My 2 cents worth.

[magwakeenercew2jh]

The punch list got a little shorter today:

Sun visors on, driver's bucket "electrified" (I'm going with the leather buckets) , slug for the rear view mirror glued to the glass,
steering wheel is on and horn 1/2 way "plumbed", took measurements for the seat bolt-down. New door handles are on.

If anyone knows what seat belts will work with these seats, that'd be a good tip for me. I bought these several years ago
and many brain cells ago...I am pretty sure the seats are GM. I found an inspection sticker under the driver's seat that says "2004".

Rear roll pan is welded in. And Butch, the body man par excellance is molding in the seams. Oh, Butch stopped the brake line leak
and is going to put a shifter shaft seal in the TH350 tomorrow....next leak to attack, bottom radiator hose .

One day closer....

[Clrussell]

Moved it from one side of the yard to the other so I could run the sprinkler, then thought real hard about installing my new headers.. But I already know they aren't going to fit so the question I'm asking my self is send em back and try to find the near impossible to find headers, or modify my clutch linkage to use the more common headers
Posted via Mobile Device

[67cheby]

just modify the linkeage

[mud.man.rj]

Modify both headers and clutck linkage if you have too, then make it come to life.

[ItsRandy]

Got the windshield installed, SafeLite...$95. Cleaned and painted the bed cross-sills.

[67cheby]

Originally Posted by ItsRandy

Got the windshield installed, SafeLite...$95. Cleaned and painted the bed cross-sills.

Looks great ! And how did you get such a good deal ?
Posted via Mobile Device

[ItsRandy]

Originally Posted by 67cheby

Looks great ! And how did you get such a good deal ?
Posted via Mobile Device

It's not what you know it's who you know and they came to my house and installed the glass. I already had the windshield gasket, which fit perfectly (thank you Brother's Truck Parts). I was originally quoted $128, I was surprised when the tech said $95, I am sure it was because I had the gasket or the tech was trying to pick me up.

[stoutguinness]

Got my truck on the road. But it doesn't sound right so I might have to do park it again haha. Seems like the carb needs tuning and possibly fuel supply problems. And after a complete bleeding of the brakes, they still go from stiff to soft and back to stiff. Maybe a leak?
Posted via Mobile Device

[Clrussell]

Any tips on modifying the linkage? I have the clutch ball that's mounted on the engine block now (between #5-#7 exhaust port) and that's right where the header tube is.. The headers I have on it now are leaking bad and are going to get replaced.. I might tear the old ones off tomorrow and take the linkage off to see what I've gotta do to make it all work.. Fabrication on linkage should be manageable
Posted via Mobile Device

[Clrussell]

Got the passenger side header on, broke the battery feed off the starter in the process.. And I'm not real sure about the thermal coating on theese headers, it seems like it is already coming off just from me installing em.. I left it in the bag while putting it between the block and frame to keep from scratching it.. But it's like the coating is rubbing off.. Has anyone watching this thread done a hydraulic clutch set up on their 4 speed?? I've been considering it but don't know enough about it. I've searched a little on it but cant find somewhere someone has said get this pt# and this part # and put it together.. I just don't want to hav to piece it together 13 times to get everything right. I'll get a picture tomorrow of progress when it's light out..
Posted via Mobile Device

[pat 70/71]

Gave my 71shorty a bath and a trip around the block(no radio just motor)good times! Cheers, Pat
Posted via Mobile Device

[jmdemon55]

took the seats and gas tank out today. drained the tank and just as we expected it was nasty nasty nasty! found the fuel level sender stuck in place and missing the float as well. that might explain why the gauge didnt move!
will be ordering a new one tommorow.

[ScottG]

Installed my Thorley headers and new exhaust. Had to notch the frame on the driver's side a bit. Looks and sounds awesome!!

[ItsRandy]

After going to the Brother's truck show I put the newly painted cross-sills back in the bed, swapped the rear springs trying to get rid of a bit of a lean, installed the rear shocks and got my exterior and interior mirrors put on. The right side mirror won't adjust so you can use it to see behind you (thank you Brother's Truck Parts).