Project: Recycle - Page 17 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

72BlckButy · 12-02-2010, 03:33 PM

Lookin' good SCOTI!

SCOTI · 12-03-2010, 01:06 AM

Today I took one step back, then two forward....

A week or so ago, I had managed to scratch one of the spindles when mocking the spindle/caliper in place. It had been about 3-4 days since I had painted it so I didn't hesitate to grab the rattle can for a little touch-up. The result was the previous paint under the 'fresh' paint started bubbling up bad.

Per manufacturer (VHT) recommendations, I had to let it cure for @ least 7-days before fixing the fix. Ten days later (today), I cut down the problem area w/some 320 dry paper, wiped it w/degreaser, & re-shot some color. Everything went on nice & smooth this time. You'd have a hard time figuring out where the 'repair' was (not that it can even be seen

).

While that was going on, I covered up the other spindle & used it as a turn-table to paint the new replacement rotors. While everything was drying, I swapped the last 2 lower a-arm sleeves into place. Now all 4 bushings are 'snug' & waiting for the chassis to be on the ground for final torqing.

I re-assembled the spindles to the control arms & went to install the rotors only to realize I no longer had the spindle nut hardware. After yet another trip to the parts store, the spindles/calipers/rotors are joined.

I wanted to throw the wheels on for a lil' look but . . ...... no lug nuts. Lug nuts are in the dually now. Getting closer though....

n2billet · 12-03-2010, 07:00 AM

DANG!!!! I'm about to tear up........looks really good Scot.

SCOTI · 12-03-2010, 10:05 AM

Quote:

Originally Posted by n2billet

DANG!!!! I'm about to tear up........looks really good Scot.

Quote:

Originally Posted by darkhorse970

Chassis looks great Scot! I love the look of fresh black paint and new hardware!

Quote:

Originally Posted by joe231

WOW!
nice work!!!

Quote:

Originally Posted by FRENCHBLUE72

Damn she is looking good...

Quote:

Originally Posted by N2TRUX

Wooohooo! Now thats some nice looking parts. No longer piled in the corner, but actually making a truck frame.

Quote:

Originally Posted by ksbrktracer

Man that thing is starting to look good .....!

Quote:

Originally Posted by Jonboy

It's really coming along well, Scot.

Thanks guys!

darkhorse970 · 12-03-2010, 07:44 AM

Chassis looks great Scot! I love the look of fresh black paint and new hardware!

joe231 · 12-03-2010, 08:03 AM

WOW!
nice work!!!
Posted via Mobile Device

**FRENCHBLUE72** · 12-03-2010, 08:47 AM

Damn she is looking good... Cant wait to see some rollers on her.

**N2TRUX** · 12-03-2010, 09:27 AM

Wooohooo! Now thats some nice looking parts. No longer piled in the corner, but actually making a truck frame.

I really like that billet hose clamp. Wish I ahd a piar of them...

ksbrktracer · 12-03-2010, 09:34 AM

Man that thing is starting to look good .....!

**67cheby** · 12-03-2010, 10:20 AM

Quote:

Originally Posted by N2TRUX

Wooohooo! Now thats some nice looking parts. No longer piled in the corner, but actually making a truck frame.

I really like that billet hose clamp. Wish I ahd a piar of them...

that would make two of us... I WONDER.......what the chance are of a guy like me and a clamp like, getting together would be???

SCOTI · 12-03-2010, 10:34 AM

Quote:

Originally Posted by 67cheby

that would make two of us... I WONDER.......what the chance are of a guy like me and a clamp like, getting together would be???

The guy that made them is the next door neighbor of my buddy (Detroit Customs). He's semi-retired & likes this kind of stuff. I wanted to do a run of 50 (25 sets) but needed to make sure they worked before asking to have more made.

If it happens, I'll let you guys know.

**67cheby** · 12-03-2010, 10:38 AM

.........So what your saying is THERE IS A CHANCE ?? (DUMB AND DUMBER)

Jonboy · 12-03-2010, 09:50 AM

It's really coming along well, Scot. Those rallies are going to be awesome on there!

SCOTI · 12-03-2010, 10:00 AM

Quote:

Originally Posted by Jonboy

It's really coming along well, Scot. Those rallies are going to be awesome on there!

No Ralleys on this one....

VA72C10 · 12-03-2010, 01:16 PM

Chassis looks great! And I like the clamps too

SCOTI · 12-04-2010, 01:58 AM

Drumroll . . ..... the chassis for 'Recycle' officially touched mother earth tonight.

There's no air in the bags (no air-lines yet) & it only has shocks on the front, but @ full dump, the frame rail was 2.5" (F) & 3.0" (R) @ the cab mount centerlines w/stock spindles (15" wheel, 27" tall tire). The upper BJ's appear to be binding (or the tie-rods) because the bags are @ approx 4.5" & the shocks are still @ 12". I should have another 1-1.5" to go up front. I'm going to disconnect the TRE's tomorrow & see if there's a change.

The rear was/is the limiting factor (as planned). It's bottomed out in the c-notch.

I'm thinkin' it will look pretty decent & should drive low full time w/plenty of ground clearance (my objective vs. trying to lay frame).

I couldn't get pics as it was too dark for pics & my cell just can't capture a good image (the shop is crowded so it's hard to get a decent view). I plan to put some schraders into place tomorrow & will roll it out in the sun for some pics......

**67cheby** · 12-04-2010, 10:17 AM

its tomorrow ......

**N2TRUX** · 12-04-2010, 12:26 PM

Quote:

Originally Posted by 67cheby

its tomorrow ......

And without pics, it never happened....

**67cheby** · 12-04-2010, 12:30 PM

LOL, i am sure everyone on this board gets tired of me harrassing them and thinks i must have nothing better to do all day every day other than ask them for pics....... Well this is mostly true , i sell cars for a living 6 days a week 10 hrs a day and most of that time right here at my desk in front of this computer... so what i am saying is ...... WHERE'S THE PICS !!

**FRENCHBLUE72** · 12-04-2010, 07:49 PM

Scoti you did a killer job on that chassis congrats man..

**lolife99** · 12-04-2010, 08:15 PM

Beautiful chassis.
What did you use for washers under the heads of all the bolts?
AN washers?

markeb01 · 12-04-2010, 09:05 PM

Absolute artwork. That chassis is really beautiful.

aggie91 · 12-04-2010, 09:33 PM

That is just beautiful! I love the wheel/hub cap set up. I think that you had a 10" rear wheel made, what size tires did you use front/rear?

After reading your post about the front BJ binding, in the pictures it looks like your upper A-Arms are upside down, possibly swapped side to side (compared to other photos I have seen)? Am I missing something about that?

Anyway, I am jealous of your progress...

tuckin55 · 12-05-2010, 12:43 AM

looks great

Alan's Classic · 12-05-2010, 12:49 AM

I'm speachless!!

12-02-2010, 03:33 PM	#1
72BlckButy Tot Roddin' Join Date: Apr 2005 Location: Mid-MO Posts: 24,461	Re: Project: Recycle Lookin' good SCOTI! __________________ -Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package)

12-03-2010, 01:06 AM	#2
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 21,934	Re: Project: Recycle Today I took one step back, then two forward.... A week or so ago, I had managed to scratch one of the spindles when mocking the spindle/caliper in place. It had been about 3-4 days since I had painted it so I didn't hesitate to grab the rattle can for a little touch-up. The result was the previous paint under the 'fresh' paint started bubbling up bad. Per manufacturer (VHT) recommendations, I had to let it cure for @ least 7-days before fixing the fix. Ten days later (today), I cut down the problem area w/some 320 dry paper, wiped it w/degreaser, & re-shot some color. Everything went on nice & smooth this time. You'd have a hard time figuring out where the 'repair' was (not that it can even be seen ). While that was going on, I covered up the other spindle & used it as a turn-table to paint the new replacement rotors. While everything was drying, I swapped the last 2 lower a-arm sleeves into place. Now all 4 bushings are 'snug' & waiting for the chassis to be on the ground for final torqing. I re-assembled the spindles to the control arms & went to install the rotors only to realize I no longer had the spindle nut hardware. After yet another trip to the parts store, the spindles/calipers/rotors are joined. I wanted to throw the wheels on for a lil' look but . . ...... no lug nuts. Lug nuts are in the dually now. Getting closer though.... Attached Images __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.* Last edited by SCOTI; 12-03-2010 at 01:07 AM.

12-03-2010, 07:00 AM	#3
n2billet Village Idiot.... Join Date: Jul 2003 Location: Rowlett, Texas Posts: 1,833	Re: Project: Recycle DANG!!!! I'm about to tear up........looks really good Scot. __________________ http://www.hubgarage.com/mygarage/n2billet -67 SWB Custom Porterbuilt Front and rear 20/22's Hazel Sold -71 StepSide Porterbuilt Stage 2 with 20/22's Stella Mae Sold

12-03-2010, 07:44 AM	#5
darkhorse970 Registered User Join Date: May 2009 Location: Monroe, LA Posts: 2,103	Re: Project: Recycle Chassis looks great Scot! I love the look of fresh black paint and new hardware! __________________ Keith SOLD - 1963 C10 Short Fleet 350/700R4 4/6 drop 1967 GMC Super Custom - Short Fleet COPO concept w/427 BBC T-400 w/Doug Nash overdrive 4/6 Drop, Buddy Buckets, etc... Frame Off (In Progress) I call it "Vulgar Display of Power" 1980 Silverado Original paint 49k Original miles 4/6 drop Check out my build thread here: http://67-72chevytrucks.com/vboard/s...=1#post6209941

12-03-2010, 08:03 AM	#6
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: Project: Recycle WOW! nice work!!! Posted via Mobile Device __________________ *CHEVY ONLY*

12-03-2010, 08:47 AM	#7
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,591	Re: Project: Recycle Damn she is looking good... Cant wait to see some rollers on her. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

12-03-2010, 09:27 AM	#8
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,023	Re: Project: Recycle Wooohooo! Now thats some nice looking parts. No longer piled in the corner, but actually making a truck frame. I really like that billet hose clamp. Wish I ahd a piar of them... __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra"

12-03-2010, 09:34 AM	#9
ksbrktracer TNT-MOTORSPORTS Join Date: Mar 2008 Location: TULSA OKLAHOMA Posts: 2,692	Re: Project: Recycle Man that thing is starting to look good .....!

12-03-2010, 10:38 AM	#12
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: Project: Recycle .........So what your saying is THERE IS A CHANCE ?? (DUMB AND DUMBER) __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

12-03-2010, 09:50 AM	#13
Jonboy Slots go on anything! Join Date: May 2003 Location: Richardson, TX Posts: 5,957	Re: Project: Recycle It's really coming along well, Scot. Those rallies are going to be awesome on there! __________________ 1974 Jimmy- 5.3/4L80e/NP241

12-03-2010, 01:16 PM	#15
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Project: Recycle Chassis looks great! And I like the clamps too __________________ Looking for a 67-72 swb or blazer project in or around VA.

12-04-2010, 01:58 AM	#16
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 21,934	Re: Project: Recycle Drumroll . . ..... the chassis for 'Recycle' officially touched mother earth tonight. There's no air in the bags (no air-lines yet) & it only has shocks on the front, but @ full dump, the frame rail was 2.5" (F) & 3.0" (R) @ the cab mount centerlines w/stock spindles (15" wheel, 27" tall tire). The upper BJ's appear to be binding (or the tie-rods) because the bags are @ approx 4.5" & the shocks are still @ 12". I should have another 1-1.5" to go up front. I'm going to disconnect the TRE's tomorrow & see if there's a change. The rear was/is the limiting factor (as planned). It's bottomed out in the c-notch. I'm thinkin' it will look pretty decent & should drive low full time w/plenty of ground clearance (my objective vs. trying to lay frame). I couldn't get pics as it was too dark for pics & my cell just can't capture a good image (the shop is crowded so it's hard to get a decent view). I plan to put some schraders into place tomorrow & will roll it out in the sun for some pics...... __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.* Last edited by SCOTI; 12-04-2010 at 01:59 AM.

12-04-2010, 10:17 AM	#17
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: Project: Recycle its tomorrow ...... __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

12-04-2010, 12:30 PM	#19
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: Project: Recycle LOL, i am sure everyone on this board gets tired of me harrassing them and thinks i must have nothing better to do all day every day other than ask them for pics....... Well this is mostly true , i sell cars for a living 6 days a week 10 hrs a day and most of that time right here at my desk in front of this computer... so what i am saying is ...... WHERE'S THE PICS !! __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

12-04-2010, 07:49 PM	#20
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,591	Re: Project: Recycle Scoti you did a killer job on that chassis congrats man.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..



Register or Log In To remove these advertisements.

12-04-2010, 08:15 PM	#21
lolife99 67-72 parts collector,… Join Date: Nov 2002 Location: Mid-MO Posts: 22,687	Re: Project: Recycle Beautiful chassis. What did you use for washers under the heads of all the bolts? AN washers? __________________ Keith Convert to disc brakes. http://67-72chevytrucks.com/vboard/s...d.php?t=444823

12-04-2010, 09:05 PM	#22
markeb01 Senior Enthusiast Join Date: Feb 2007 Location: Spokane Valley, WA Posts: 8,356	Re: Project: Recycle Absolute artwork. That chassis is really beautiful.

12-04-2010, 09:33 PM	#23
aggie91 I'm just glad to be here! Join Date: Jan 2008 Location: Longview, TX Posts: 4,788	Re: Project: Recycle That is just beautiful! I love the wheel/hub cap set up. I think that you had a 10" rear wheel made, what size tires did you use front/rear? After reading your post about the front BJ binding, in the pictures it looks like your upper A-Arms are upside down, possibly swapped side to side (compared to other photos I have seen)? Am I missing something about that? Anyway, I am jealous of your progress... __________________ Karl 1965 Chevy Stepside(Grandpa's Old Blue) and (July 2015 Shop Build!)(2020, the Saga Continues) http://67-72chevytrucks.com/vboard/s...d.php?t=372424 The LST Challenge: http://67-72chevytrucks.com/vboard/s...=1#post7812257 Korbin's 1st Square: "Sunburn" http://67-72chevytrucks.com/vboard/s...d.php?t=418618 1985 GMC Sierra: "White Trash", Korbin's 2nd now... http://67-72chevytrucks.com/vboard/s...d.php?t=632305 Henry - 1984 Chevrolet, Owen's 1st Square

12-05-2010, 12:43 AM	#24
tuckin55 Registered User Join Date: Feb 2008 Location: Mesquite tx Posts: 54	Re: Project: Recycle looks great

12-05-2010, 12:49 AM	#25
Alan's Classic 1 thing at a time is progress. Join Date: Jun 2007 Location: Ball Ground GA Posts: 5,511	Re: Project: Recycle I'm speachless!! __________________ Alan Philippians 2:14-16 Alan's Classic Facebook page. North Georgia Group Project 1965 Vitamin C-10 1995 GMC Sierra K1500 The "Wrecker"

Register or Log In To remove these advertisements.