![]() |
![]() |
#4351 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,828
|
Re: Restoring Rusty
and just a pic of the old Gorilla snot on the floor after stripping it off the driver's side
|
![]() |
![]() |
![]() |
#4352 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,828
|
Re: Restoring Rusty
I must say I am very please with the quality and fitment of these parts, Classic Parts does it again, I liked their rear window seal very much, and now they are 2 for 2 with the door weatherstrips as well
|
![]() |
![]() |
![]() |
#4353 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,828
|
Re: Restoring Rusty
did I mention the wife is gone for the weekend on an all girls camping trip, well on with the show than, what's next
and the next patient is Steering..., Mr. Manuel Steering |
![]() |
![]() |
![]() |
#4354 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,828
|
Re: Restoring Rusty - Saginaw Manual Steering Box
and after a little belly rub we get our money shot, that's right folks The Greg is a Parts Numbers Junkie - PNJ
and a quick AltaVista search for 5698180 (yeah remember that site) reveals this there box is a box formely known as Saginaw - nice Last edited by Gregski; 07-17-2016 at 10:02 PM. |
![]() |
![]() |
![]() |
#4355 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,828
|
Re: Restoring Rusty - Pitman Arm
now let's check out that Pitbull Arm
I bought it with the pitman arm because I recon there is a difference between the manual and the power arms |
![]() |
![]() |
![]() |
#4356 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,828
|
Re: Restoring Rusty
then it was time to make a mess - we tore into it because it sounded like it had square bearings inside, something wasn't right
TOP TIP: to get that three bolt cover off, don't tap it with a hammer or pull on it (I'm just sayin') unscrew the middle screw with a flat screw driver and watch it come off |
![]() |
![]() |
![]() |
#4357 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,828
|
Re: Restoring Rusty
a better look inside after cleaning it up a bit with some paper towels
I am in awe of this simple yet effective engineering, ah the good ol' days |
![]() |
![]() |
![]() |
#4358 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,828
|
Re: Restoring Rusty
getting the two big nuts off was a major P.I.A. I won't lie to you, after my adjustable wrench got me no where I had to go out and buy a 1 5/16 socket and use a 5 foot long cheater bar on it to loosen the pitman arm nut, jeez
than I had to use a puller to get the pitman arm off Fun Level = 2.7 |
![]() |
![]() |
![]() |
#4359 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,828
|
Re: Restoring Rusty
but we persevered and got that pitman arm shaft out and even managed to clean it up a bit
|
![]() |
![]() |
![]() |
#4360 |
Registered User
Join Date: May 2016
Location: Sun City, CA
Posts: 34
|
Re: Restoring Rusty
|
![]() |
![]() |
![]() |
#4361 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,828
|
Re: Restoring Rusty
getting the worm gear out was no picnic either, but got it out too
I think this is where we first spotted to completely busted up bearing, it was shattered Mess Level = 11.5 |
![]() |
![]() |
![]() |
#4362 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,828
|
Re: Restoring Rusty
|
![]() |
![]() |
![]() |
#4363 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,828
|
Re: Restoring Rusty
couldn't get to the third flat screw this way, so realized the rag joint has to come off to fully slide it out - even the rag joint needed a puller to git off
|
![]() |
![]() |
![]() |
#4364 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,828
|
Re: Restoring Rusty
getting there, this is the last pic for the night, but I did take the ball bearings out of that thing that sits on the warm gear, and hopefully I didn't loose none
|
![]() |
![]() |
![]() |
#4365 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,828
|
Re: Restoring Rusty
... oh oh, the wife just pulled in the driveway, time to vacuum the house...
|
![]() |
![]() |
![]() |
#4366 | |
Senior Member
![]() Join Date: Jul 2000
Location: North Texas
Posts: 3,488
|
Re: Restoring Rusty
Quote:
Disposal fee for what? The core you should have given them? Greg, this is Sanity calling. Convert to manual steering? Do you have a 24" diameter steering wheel? Or Arnold's biceps? ![]() I went the opposite direction on my old 69 C10. Converting to PS was more bang-for-the-buck than any mod I did on that truck, just ahead of dual exhausts. And I did it all with junkyard parts. Only downside was my then 17 year old daughter decided she liked to drive it.
__________________
Mike 1969 C10 LWB -- owned for 35 years. 350/TH350, 3.08 posi, 1st Gen Vintage Air, AAW wiring harness, 5-lug conversion, 1985 spindles and brakes. 1982 C10 SWB -- sold 1981 C10 Silverado LWB -- sold, but wish I still had it! 1969 C10 (not the current one) that I bought in the early 1980s. Paid $1200; sold for $1500 a few years later. Just a hint at the appreciation that was coming. Retired as a factory automation products salesman. Worked part-time over the years for an engine builder and a classic car repair shop. Member here for 24 years! This is the very first car/truck Internet forum I joined. I still used a dial-up modem back then! |
|
![]() |
![]() |
![]() |
#4367 |
Registered User
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 2,228
|
Re: Restoring Rusty
__________________
1961 Apache: "Grabber Orange" Shortboxed, pancake, step-notch, air-ride, boosted-LS 1977 Silverado: Shortboxed & dropped, potato-potato V8 Pontiac Firefly (Chevy Sprint): The ultimate engine swap: 5.7L in a 1.0L bag Lotus Super 7 Replica: Scratch-built street-legal rollerskate |
![]() |
![]() |
![]() |
#4368 |
Registered User
Join Date: Feb 2007
Location: Memphis MI
Posts: 1,851
|
Manwel steering
The single complaint my 6'6", 300# father had about his 1981 GMC with a straight six and 3OTT (ie a light as you can get truck) was that the manual steering with the stock wheel was very high effort. I actually used to have to have the seat belt cinched down tight to keep me in the seat to turn the wheels sitting still on concrete.
I strongly beg to to reconsider. On the other hand your wife will drive the truck once in a concrete parking lot and then will never do it again. I have manual steering in the truck I'm looking at drag racing. All the DD's will / do be power, and I'm a man who likes my trucks with no frills (5 squares, exactly 1 set power doors...)
__________________
1987 2 ton ![]() 1982 ![]() Dad's 1981 ![]() Plus a mess o' tractors |
![]() |
![]() |
![]() |
#4369 |
Registered User
Join Date: Sep 2012
Location: Midway, NC
Posts: 3,275
|
Re: Restoring Rusty
Manual steering. I'm in big time. I've been considering it too for my old rag. I've got my reasons. Lol. It's funny to me but my truck has manual brakes. Everybody wants power brakes. Honestly I never cared for power brakes. My old 74 had power brakes and I never really cared for it. I'm a bird of a different feather.
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=581873 The low buck build threads. Check'em out! http://67-72chevytrucks.com/vboard/s...d.php?t=666022 My build thread Crossmembers CC |
![]() |
![]() |
![]() |
#4370 | |
Senior Member
![]() Join Date: Jul 2000
Location: North Texas
Posts: 3,488
|
Re: Restoring Rusty
Quote:
I will admit that the rear has new riveted shoes, finned drums, and wheel cylinders. Even springs and most of the hardware is new. All I did to the front was replace the nearly worn-out pads with some mid-level pads from O'Reilly Auto. Someday I'll probably get loaded calipers with Wagner Thermo Quiet pads and have the rotors turned.
__________________
Mike 1969 C10 LWB -- owned for 35 years. 350/TH350, 3.08 posi, 1st Gen Vintage Air, AAW wiring harness, 5-lug conversion, 1985 spindles and brakes. 1982 C10 SWB -- sold 1981 C10 Silverado LWB -- sold, but wish I still had it! 1969 C10 (not the current one) that I bought in the early 1980s. Paid $1200; sold for $1500 a few years later. Just a hint at the appreciation that was coming. Retired as a factory automation products salesman. Worked part-time over the years for an engine builder and a classic car repair shop. Member here for 24 years! This is the very first car/truck Internet forum I joined. I still used a dial-up modem back then! |
|
![]() |
![]() |
![]() |
#4371 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,828
|
Re: Restoring Rusty
did I mention I have a daughter too, who will be driving in a few years, ha ha, a man must protect his investment
|
![]() |
![]() |
![]() |
#4372 | |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,828
|
Re: Restoring Rusty
Quote:
|
|
![]() |
![]() |
![]() |
#4373 | |
Registered User
Join Date: Nov 2015
Location: Smethport, PA
Posts: 1,213
|
Re: Restoring Rusty
Quote:
__________________
85 K30 crew cab dually - Project http://67-72chevytrucks.com/vboard/s...d.php?t=694939 87 Wrangler Rock Crawler - Reason for the project http://www.wranglerforum.com/f330/da...ld-122601.html 04 1500 crew cab http://67-72chevytrucks.com/vboard/s...d.php?t=786514 |
|
![]() |
![]() |
![]() |
#4374 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,828
|
Re: Restoring Rusty
the latest addition to the workshop, man it feels good to be back in the game, looks right at home on that cart don't it
let there be sparks those of you familiar with the Lincoln MIG 110 volt machines may pick up that this is the 140C model, the C stands for "Can't get it from Lowe's or Home Depot" ha ha it's a step above the Retail machines and costs twice as much and weighs twice as much as well, has better guts made of metal rather than plastic, etc. also I can get the spool gun for it if and when the time comes to stick some thin aluminum together The Greg is Happy! |
![]() |
![]() |
![]() |
#4375 | |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,828
|
Re: Restoring Rusty
Quote:
|
|
![]() |
![]() |
![]() |
Bookmarks |
|
|