What did you do to your truck today? - Page 18 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

sams60gmc · 12-20-2009, 10:49 PM

I sanded some of the rust off of my roof and then spread a little filler and got it sanded back down.

scotts62 · 12-20-2009, 11:58 PM

Put my trans on the work table, going to attempt my first rebuild

Woogeroo · 12-19-2009, 11:32 PM

I installed the new voltage regulator and ran a ground wire from the ground post on the new alternator.

The biggest aggravation were getting the nuts onto the 3 bolts that hold the v. reg. to the radiator support.

yeesh!

it is running and charging again tho', so yay!

-W

sams60gmc · 12-20-2009, 12:00 AM

I moved my truck out of the garage yesterday to work on my buddies Honda, then moved it back in today. I took a pic because I thought it looked cool. I had to have him sit in the engine bay and put gas in the carb out of a bottle because my fuel pump went out.

TwoFiftyShifter · 12-20-2009, 12:07 AM

Cut the exhaust off of my truck right off the manifold, de-rusted and painted the headers, got that little 6 running a bit better. More to come tomorrow.

low79fx · 12-20-2009, 11:48 AM

Blasted and painted cateye capsules to install new lenses for my 65 GMC,fixed the horn button on steering wheel,cut out exhaust to pipe up to headers.And tested all lights,turn signals and brake lights.Almost ready for inspection.YEAH!

*LILRED66* · 12-20-2009, 12:32 PM

We made a little more progress on OLRED66.

*LILRED66* · 12-20-2009, 12:34 PM

And a few more of our progress...

Turkey · 12-20-2009, 02:52 PM

sanded and primered the tailgate...sorted and put away all of the tools that have acquired in the bed

SCOTI · 12-20-2009, 09:27 PM

Made templates & started fabbing my new rear upper shock mounts. I needed 17" overall length @ ride height & was shooting for 60° angle. I think my number crunching worked . . ....

shortbed70 · 12-20-2009, 10:04 PM

Got both front fenders sanded and maybe some paint this week.

jgh64pkup · 12-22-2009, 01:58 AM

i did nothing again

*LILRED66* · 12-22-2009, 10:04 AM

We did some rearranging...to make room for more trucks inside the fence, we had a 40' container delivered and set, to put sheetmetal items out of the weather.

70 Suburban · 12-22-2009, 10:15 AM

Thats a-maze-ing

70 Suburban · 12-22-2009, 11:07 AM

I know i need onw.. the ear on my 750 dbl pump just broke off. The carb is great but the base is screwd.

**nbrfd007** · 12-22-2009, 11:39 AM

Put a master/clutch cylinder on it. Getting ready for swapping the carb to a 500 holley on my 305 V6.
Tim

NF65Fleetside · 12-22-2009, 08:48 PM

I freak'n broke my turn signal switch! guh now one more thing I gotta pickup from the shop when I go get some other items. =(

ruffrida2005 · 12-23-2009, 04:52 AM

Well i looked at my frame again, it's not doing any tricks like I thought. I got my rebuild kit in for my Demon, it cost me free dollars.

The 750 is for sell $250, never had gas in it. only set on the intake!

63deluxfleet · 12-23-2009, 09:36 PM

Filled her up...hopefully not for the last time, but probably if insurance don't pay for my hit and run total....
Took a long drive and tried to enjoy her a lil...

ravens65 · 12-23-2009, 10:38 PM

work on the wiring again today pita , why did they call it e-z wiring ????

jgh64pkup · 12-24-2009, 12:35 AM

Quote:

Originally Posted by ERIC BUFFARD

work on the wiring again today pita , why did they call it e-z wiring ????

they are ez

if a 15 year old can install one in a few days im sure you can

Vernski · 12-24-2009, 01:05 AM

Quote:

Originally Posted by jgh64pkup

they are ez

if a 15 year old can install one in a few days im sure you can

Gage it's not easy for older guys to stand on there heads an do wiring under the dash. I'm ok if I take my time and I've taken my blood pressure pills.I'm speaking of myself only.

---Vernski

ravens65 · 12-24-2009, 09:11 AM

thats no average 15yr old to do his own wiring!! most of them are to busy w/ video games to learn this stuff!! its not as hard as I thought, just seems overwelming @ first

jgh64pkup · 12-24-2009, 01:07 AM

sams60gmc · 12-24-2009, 02:57 AM

Today I started the day off working on my poly bushing sleves. I made them out of solid stock because I couldn't find any tube and I'm that cheap!! Then I built a new cross member because I wasn't happy with the way my old one was fitting and we screwed up some how and it ended up being way too high. I forgot to compensate for the 4'' tubing that it would be notched into. Anyways I built a new one out of 2x3 tubing and welded that up and removed the temporary support for up front. I also made some bag mounts. Next week I'll make my lower bag mounts and start setting up my links. Anyways pics!

12-20-2009, 10:49 PM	#1
sams60gmc Registered User Join Date: Sep 2008 Location: Vancouver Washington Posts: 726	Re: What did you do to your truck today? I sanded some of the rust off of my roof and then spread a little filler and got it sanded back down. __________________ 1960 GMC short fleet, full frame build... http://67-72chevytrucks.com/vboard/s...d.php?t=329718

12-20-2009, 11:58 PM	#2
scotts62 One day... Join Date: Apr 2008 Location: Tuttle, Ok Posts: 9,240	Re: What did you do to your truck today? Put my trans on the work table, going to attempt my first rebuild __________________ Scott 93 crew cab build Project 62

12-19-2009, 11:32 PM	#3
Woogeroo Registered User Join Date: Aug 2003 Location: tool box Posts: 3,115	Re: What did you do to your truck today? I installed the new voltage regulator and ran a ground wire from the ground post on the new alternator. The biggest aggravation were getting the nuts onto the 3 bolts that hold the v. reg. to the radiator support. yeesh! it is running and charging again tho', so yay! -W

12-20-2009, 12:00 AM	#4
sams60gmc Registered User Join Date: Sep 2008 Location: Vancouver Washington Posts: 726	Re: What did you do to your truck today? I moved my truck out of the garage yesterday to work on my buddies Honda, then moved it back in today. I took a pic because I thought it looked cool. I had to have him sit in the engine bay and put gas in the carb out of a bottle because my fuel pump went out. Attached Images __________________ 1960 GMC short fleet, full frame build... http://67-72chevytrucks.com/vboard/s...d.php?t=329718

12-20-2009, 12:07 AM	#5
TwoFiftyShifter Registered User Join Date: Nov 2008 Location: Gwinnett GA Posts: 1,803	Re: What did you do to your truck today? Cut the exhaust off of my truck right off the manifold, de-rusted and painted the headers, got that little 6 running a bit better. More to come tomorrow. __________________ 1982 K10 SWB 1987 V20 - Sold - Doh!

12-20-2009, 11:48 AM	#6
low79fx Registered User Join Date: Jun 2008 Location: odessa,tx Posts: 208	Re: What did you do to your truck today? Blasted and painted cateye capsules to install new lenses for my 65 GMC,fixed the horn button on steering wheel,cut out exhaust to pipe up to headers.And tested all lights,turn signals and brake lights.Almost ready for inspection.YEAH!

12-20-2009, 12:32 PM	#7
LILRED66 Account Suspended Join Date: May 2005 Location: Kansas City, KS Posts: 3,906	Re: What did you do to your truck today? We made a little more progress on OLRED66. Attached Images

12-20-2009, 12:34 PM	#8
LILRED66 Account Suspended Join Date: May 2005 Location: Kansas City, KS Posts: 3,906	Re: What did you do to your truck today? And a few more of our progress... Attached Images

12-20-2009, 02:52 PM	#9
Turkey Registered User Join Date: Dec 2009 Location: Orlando, Florida Posts: 427	Re: What did you do to your truck today? sanded and primered the tailgate...sorted and put away all of the tools that have acquired in the bed

12-20-2009, 09:27 PM	#10
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 21,938	Re: What did you do to your truck today? Made templates & started fabbing my new rear upper shock mounts. I needed 17" overall length @ ride height & was shooting for 60° angle. I think my number crunching worked . . .... Attached Images __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

12-20-2009, 10:04 PM	#11
shortbed70 Registered User Join Date: Mar 2002 Location: Forney TX Posts: 4,512	Re: What did you do to your truck today? Got both front fenders sanded and maybe some paint this week. __________________ Troy 1965 Chevy Bagged,361 sbc,voodoo cam,1.5 full roller rockers,patriot 185cc vortec heads 2.02-1.60,vortec weiand polished intake,demon carb my truckhttp://67-72chevytrucks.com/vboard/s...d.php?t=332884 Big Red Dog build http://67-72chevytrucks.com/vboard/s...d.php?t=572274

12-22-2009, 01:58 AM	#12
jgh64pkup Sunburst C10!!! Join Date: Jan 2009 Location: Texas Posts: 2,560	Re: What did you do to your truck today? i did nothing again __________________ Gage 1967 C10 Shortbed Stepside

12-22-2009, 10:04 AM	#13
LILRED66 Account Suspended Join Date: May 2005 Location: Kansas City, KS Posts: 3,906	Re: What did you do to your truck today? We did some rearranging...to make room for more trucks inside the fence, we had a 40' container delivered and set, to put sheetmetal items out of the weather. Attached Images Last edited by LILRED66; 12-22-2009 at 10:06 AM.

12-22-2009, 10:15 AM	#14
70 Suburban Rods Join Date: Nov 2002 Location: Bryan, TX Posts: 1,398	Re: What did you do to your truck today? Thats a-maze-ing __________________ Just keepin it simple. 1965 C-10 Ext cab build. 350??(Does it count at 2 truck if I had to cut one up?) 1966 C-10 lwb 283 auto 1970 Suburban in pieces 1971 Blazer 4wd....restore someday. all factory CST 1972 Blazer 4wd parts truck still a roller 1972 GMC Sierra Grandee 1998 Chevy ext driver. 2005 F**D the wife drive...(cant fix women)

12-22-2009, 11:07 AM	#15
70 Suburban Rods Join Date: Nov 2002 Location: Bryan, TX Posts: 1,398	Re: What did you do to your truck today? I know i need onw.. the ear on my 750 dbl pump just broke off. The carb is great but the base is screwd. __________________ Just keepin it simple. 1965 C-10 Ext cab build. 350??(Does it count at 2 truck if I had to cut one up?) 1966 C-10 lwb 283 auto 1970 Suburban in pieces 1971 Blazer 4wd....restore someday. all factory CST 1972 Blazer 4wd parts truck still a roller 1972 GMC Sierra Grandee 1998 Chevy ext driver. 2005 F**D the wife drive...(cant fix women)



Register or Log In To remove these advertisements.

12-22-2009, 11:39 AM	#16
nbrfd007 Senior Member Join Date: Nov 2007 Location: New Blaine, Arkansas Posts: 751	Re: What did you do to your truck today? Put a master/clutch cylinder on it. Getting ready for swapping the carb to a 500 holley on my 305 V6. Tim

12-22-2009, 08:48 PM	#17
NF65Fleetside Registered User Join Date: Feb 2007 Location: Los Angeles Posts: 674	Re: What did you do to your truck today? I freak'n broke my turn signal switch! guh now one more thing I gotta pickup from the shop when I go get some other items. =(

12-23-2009, 04:52 AM	#18
ruffrida2005 Member of the longbed union. Join Date: Feb 2009 Location: Killeen, Tx Posts: 2,158	Re: What did you do to your truck today? Well i looked at my frame again, it's not doing any tricks like I thought. I got my rebuild kit in for my Demon, it cost me free dollars. The 750 is for sell $250, never had gas in it. only set on the intake! __________________ Paul 88 GMC Crew Cab dually, 454/T400 64 LWB 400 HP 350/350T Bagged, under construction! Sold most of it! 92 S10 Iron Duke 5 speed, 5/7 drop for now. soon to be bagged. Sold http://67-72chevytrucks.com/vboard/s...59#post4637759

12-23-2009, 09:36 PM	#19
63deluxfleet Registered User Join Date: Jun 2009 Location: dinuba, ca Posts: 623	Re: What did you do to your truck today? Filled her up...hopefully not for the last time, but probably if insurance don't pay for my hit and run total.... Took a long drive and tried to enjoy her a lil... Attached Images __________________ A girl phoned me the other day and said... Come on over, there's nobody home. I went over. Nobody was home. -Rodney Dangerfield .......THE ROAD TO HELL IS PAVED WITH GOOD INTENTIONS.....

12-23-2009, 10:38 PM	#20
ravens65 Registered User Join Date: Dec 2009 Location: clermont florida Posts: 176	Re: What did you do to your truck today? work on the wiring again today pita , why did they call it e-z wiring ???? Attached Images

12-24-2009, 09:11 AM	#23
ravens65 Registered User Join Date: Dec 2009 Location: clermont florida Posts: 176	Re: What did you do to your truck today? thats no average 15yr old to do his own wiring!! most of them are to busy w/ video games to learn this stuff!! its not as hard as I thought, just seems overwelming @ first Last edited by ravens65; 12-24-2009 at 09:12 AM.

12-24-2009, 01:07 AM	#24
jgh64pkup Sunburst C10!!! Join Date: Jan 2009 Location: Texas Posts: 2,560	Re: What did you do to your truck today? __________________ Gage 1967 C10 Shortbed Stepside

12-24-2009, 02:57 AM	#25
sams60gmc Registered User Join Date: Sep 2008 Location: Vancouver Washington Posts: 726	Re: What did you do to your truck today? Today I started the day off working on my poly bushing sleves. I made them out of solid stock because I couldn't find any tube and I'm that cheap!! Then I built a new cross member because I wasn't happy with the way my old one was fitting and we screwed up some how and it ended up being way too high. I forgot to compensate for the 4'' tubing that it would be notched into. Anyways I built a new one out of 2x3 tubing and welded that up and removed the temporary support for up front. I also made some bag mounts. Next week I'll make my lower bag mounts and start setting up my links. Anyways pics! Attached Images __________________ 1960 GMC short fleet, full frame build... http://67-72chevytrucks.com/vboard/s...d.php?t=329718

Register or Log In To remove these advertisements.